@@CraftRectify ......I tried with bc547 transistor. .but that transistor is too much heated ....but working. .....is there any any solution ??for not heating up and also getting same high amount of power
Bro AP jab en dono main say koi bhi transistor use kar rahay ho or wo heat ho raha hai to transistor Kay base par resistance use kar saktay ho ya AP voltage Kam par banao jaisay mainy banaya tha mje 13007 Jo energy saver main say nikalta hai us say mairay pas voltage 3 say 5 thay lakin agar 12 voltage par layjata hu to heat hota hai to us hisab say resistance laga saktay ho
@@maroyedipti4 bro...i need your help. I wanted to make a project with this. "Wireless EV Charging station" Can we use this wireless system for project. Need your suggestion.
When electric current is supplied to a coil or wire there will be a magnetic field around it and the change in magnet field induce emf by that induced current is produced and that is transmitted from one coil to another through magnetic field
2nd coil 10-15 turns And Volt is 20-25 ampear it draws around 40-50 Milli amps of current with no load but with load it consumes around 1.5 amps or more depending on voltage and load
Kalo dgn tegangan tnggi aku belum,bisa menemukan cara yg aman merAngkainya,coba deh bikinkan animasi yg 220 volt dan aman,,,,aku baru bisa mentransfer dibawah 5 volt jarak dekat
![Oscar Maydon x Fuerza Regida - Tu Boda [Official Video]](http://i.ytimg.com/vi/_ymicn0_GYc/mqdefault.jpg)
This is awesome work... I had some doubt ! How many wounds did you wound a copper coil (both receiver and transmitter coil)
The input voltage as in the video is 5V, is this DC or AC? And if it is a DC , isn't the input AC ? Thank you
Which number of copper wire you have used in this project?
Is it 12v or 21v as shown in ur tutorial
Bro can I use a 5v - 1A/2A DC power supply as input
Which type of supply you give to circuit?
AC or DC
Do you provide the primary with AC? Any battery / power brick would output DC no?
does the phone battery got really charged up??
Which type of capacitor is it? Super cap?
Bro can we use any other transistor like bd30....bc547....or induction cooker transistor. ...and 50v 100uf capacitor..
You may try
@@CraftRectify ......I tried with bc547 transistor. .but that transistor is too much heated ....but working. .....is there any any solution ??for not heating up and also getting same high amount of power
Bro AP jab en dono main say koi bhi transistor use kar rahay ho or wo heat ho raha hai to transistor Kay base par resistance use kar saktay ho ya AP voltage Kam par banao jaisay mainy banaya tha mje 13007 Jo energy saver main say nikalta hai us say mairay pas voltage 3 say 5 thay lakin agar 12 voltage par layjata hu to heat hota hai to us hisab say resistance laga saktay ho
@@maroyedipti4 bro...i need your help.
I wanted to make a project with this.
"Wireless EV Charging station"
Can we use this wireless system for project.
Need your suggestion.
What is the concept behind this? Can someone please explain the working principle
Electro magnet inducting, current is produced by magnetic field
Its works but if you dont have a transistor use a dc motor
Agar hum kum guage ki wire lenge to nahi chalega kya?
Chal jayega
The input and output is 12v ?
If you whon to use 12v you know i use 5v it's work !
5v is Ac or Dc
Which amper charge module?
1.5 amp
Why don't you tell me how many turns is the second coil?
If the primary is 15-0-15 turns then secondary will be 15+15 = 30 turns...and similarly
Thanks bhai for this video
When electric current is supplied to a coil or wire there will be a magnetic field around it and the change in magnet field induce emf by that induced current is produced and that is transmitted from one coil to another through magnetic field
5 volt regulator ic 1.2 amps not charging maximum 2amps 5 voltage power supply
its Enough to charge cell phone
What is the coil name?
Nie podałeś w opisie Jakiej średnicy ma być drut nawojowy
i also used the pc power supply's heat sink
Is the mosfet heating..???
Yes !
Hello sir good afternoon
Mujhko yahi project chahiye bataiye kaese milega please 🙏🙏🙏
Bana lo
I followed all the steps and it didn't work
Bro it's work 100% really i do this at home !
Did you use mosfet ? It's very Necessarily
Bro if your not working use 2n2222 transistor instead of the irf4
Kitne guage ka wire hai??
22 gauge ki wire h
@@CraftRectify Aur supply kitne volt ka hai.... Aur kese diya h??
without Core ke Koi current pass Nahin ho sakta hai ya Jhooth hai
Nice work, nice idea
Thanks
klo 12volt bisa gk bang
C'est du courent direct ou
दुसरे कॉईल में कितने टर्न लिए ?
पॉवर सप्लाई कितने वोल्ट? ,कीतना करंट ?
कुछ भी डिटेल नहीं ?
2nd coil 10-15 turns
And Volt is 20-25 ampear it draws around 40-50 Milli amps of current with no load but with load it consumes around 1.5 amps or more depending on voltage and load
Amazing
What if we use transistor
Yes u can
Best video
Good
Kalo dgn tegangan tnggi aku belum,bisa menemukan cara yg aman merAngkainya,coba deh bikinkan animasi yg 220 volt dan aman,,,,aku baru bisa mentransfer dibawah 5 volt jarak dekat
29 gauge kamkarega
What is the use of bridge convertor in this?
The volt in reciver is AC so to convert it into DC volt we have to use a bridge rectifier bro
Completely useless as it can provide power upto 2 watts only, and phones required 18 to 35 watt for proper charging...
❤❤ good 👍 👌 👏 star 🌟 🤩 ✨️ 👌
Digo no es mas fasil enchufar un cargado a la Red electrica antes de hacer tantas pelotudeses
Bhai wirless fast charger banao
lED IS WORKING BUT MOTAR IS NOT RUNNING
Use bridge Rectifier with capacitor
That 21V isn't stable
To jest lipa tranzystor od razu się pali po podłączeniu do zasilania
Hi
Bro tar ka number kya hai?
21 gauge
No
The output is a 18 volt thin yuo put a USB pin for charger the out put is a 18volt not a 5volt not a compatible that is a fake
You shut up man he used 7805 ic so output is 5v.