Lab 3 Buck Converter in LTSpice | Power Electronics

34 Buck-Boost Converter Analysis and Design | Power Electronics
• 34 Buck-Boost Converte...
Basics of Power Electronics - Walid Issa
33 Boost Converter | Power Electronics
• 33 Boost Converter Ana...
32 Buck Converter Part 4 | Power Electronics
• 32 Buck DC/DC Converte...
31 Buck Converter Part 3 | Power Electronics
• 31 Buck Converter Desi...
30 Buck Converter Part 2 | Power Electronics
• 30 Buck Converter Anal...
29 Buck Converter Part1 | Power Electronics
• 29 Buck Converter Intr...
27 Triacs | Power Electronics
• 28 Triacs | Power Elec...
26 Thyristors | Power Electronics
• 27 Thyristors | Power ...
25 Inverters | Power Electronics
• 26 Inverters | Power ...
24 Gate Drivers | Power Electronics
• 25 Gate Drivers | Powe...
23 Mosfet Consideration | Power Electronics
• 24 Mosfet Consideratio...
22 Power Mosfet Transistors | Power Electronics
• 23 Power Mosfet Transi...
21 Power BJT Transistors| Power Electronics
• 22 Power BJT Transisto...
20 Power Diodes Types | Power Electronics
• 20 Power Diodes Types ...
19 Power Diodes | Power Electronics
• 19 Power Diodes | Powe...
18 Which Switch to Choose ? | Power Electronics
• 18 Which Switch to Cho...
Mobile Thermal Camera HT201: bit.ly/3kuREi1
17 Switching Losses (Worked Examples) | Power Electronics
• 17 Switching Losses (W...
16 Switching Losses and LTSpice | Power Electronics
• 16 Switching Losses an...
15 Ideal VS Practical Switches
• 15 Ideal VS Practical ...
Thermal Calculations using LTSpice
Part 1: • 12 Power Elecronics: T...
Part 2: • 13 Power Elecronics: T...
thermal management,thermal,power electronics,switching losses,ltspice, walid issa, power diodes, buck converter design consideration
#powerelectronics
#walidissa
power electronics,walid issa,power elecronics fundamentals,buck converter,analysis,design,katkimshow,bob trenwith,erikson,gate,matrin ordonez,linkedin,with Dr. K

[@samuelmolines3084]

I think the voltage divider R5-R6 feedback should be 9k-1k respectively so that the setting voltage 2V/3V will output 20V/30V ... thank you for your video .. the thought process is very smooth .. thank you very much for the very wonderful presentation

[@zarekgalicia5322]

Amazing Explanation Sir!! Very quite and good information about PowerElectronics! Truly amazing ! Thanks for share everything with the community. !!

[@AccidentalScience]

Nice job. I've made a buck converter myself but went straight to circuit design and physical PCB skipping the simulation (I've made a video of it if you like to check it out.) It's nice to compare the signals, particularly for the ESR. There are some differences too: I used a p channel MOSFET and an op amp for feedback.
I don't get why the simulation shows an overshot at startup. I'm referring to the beginning when the MOSFET is just driven by the PWM voltage source. It seems there is a significant LC resonance, that should be at 1590Hz, while the PWM frequency is 10KHz ... 🤔
Greetings from the Alps.
P.s. I'll put a link in the description of my video to this one as correlated.

[@kavinayaskingdom3687]

Amazing and very clear!!

[@gtag174]

Excellent tutorial Walid

[@abhi5491]

Great explanation!!!

[@roberttso1079]

Hysteresis by resistor won't work unless the 3V ref point has some source resistance. Your 10K/1K divider is 1/11th, not 1/10th. That explains your dc error. Finally, the feedback network should have intentional poles and zero to have phase margin and no oscillation.

[@WalidIssaPlusE]

Yes I agree

[@libervolucion]

I've just found this video and was about to comment exactly the same. The 11 ratio explains everything about the feedback errors.

[@mbrp5107]

superb explanation sir

[@ashutoshchakravarty2669]

Great video! Tysm

[@sassi7190]

Nice lab dr.walid

[@ahmedalanssari1599]

amazing

[@danushvenkatesh4868]

Do you have similar simulation for Boost converter

[@lafrooptimiste245]

Thanks

[@sibildas]

Circuit with the inversion of PWM towards end of the video is not working. Something is not right??

[@akjais]

at 49:23 may be R5 should be 9k

[@techiteasy5725]

yes that is the reason behind the fake steady state error.

[@sadeqmola2878]

sorry but how should we provide 5v (as v2 in this schematic) for comparator supply from the only source which we have (input) in real circuit applications?

[@ashutoshchakravarty2669]

kindly ground the other end

[@sadeqmola2878]

@@ashutoshchakravarty2669 which end?
in this schematic, comparator supply pin is not grounded, it is pulled up to 5v.
my question is how to provide this 5v out of the only source which we have (input source)?

[@eewitht3190]

thanks. plz also share LTspice file by uploading to drive and sharing link of it

[@WalidIssaPlusE]

Sorry for this but I can't as my students should do this and sharing that will make the lesson useless

[@ahmedalawadh6818]

سلام عليكم اخي عندي مشكلة فالبرنامج ياريت اتواصل معاك خاص

[@ahmedalanssari1599]

Do you have simulation for Boost converter