How to Install a Strap Boss | Connect Waste to Soil Pipe
HTML-код
- Опубликовано: 9 фев 2025
- Welcome to my tutorial on how to fit a strap boss to a soil pipe. I will guide you step by step how to connect a waste pipe to a stack or soil pipe. If you like the content leave a like and please subscribe for more content like this as I've got a lot more to come and there will be something that will help you out.
Links to the parts i recommend below.
Holesaw and Arbour - amzn.to/2UqW5lV
Floplast Strap Boss - amzn.to/3ynUzPY
Solvent Weld - amzn.to/3jWptea
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
/ thediyguy1
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The DIY Guy may earn affiliate commission if you purchase via the recommended links. These links will not cost you any extra.
As always. Precise and clear. Exactly what you need to do and no pointless twaddle. Short,sweet and spot on.
Thanks 👍
Do the soil stack boss 'straps' open wide enough to slide onto the stack pipe? I don't have the luxury of sliding the boss over the end of the stack pipe.
Pure Gold, so glad I found this before tackling a very awkward job. Subscribed immediately.
Thanks for subscribing
Where you put the rubber, could you solvent weld as well? And the pipe you put in the rubber is pushfit or solver weld?
Nice and clear demo off upstairs to attempt bath connection to horizontal waste pipe.
Absolutely nice 👍.
Thank you! Cheers!
Excellent video great job
Thank you great content helped me a lot sort some pips in the house
Watch this before attempting and it made life easier. Thanks 👍🏻
Great 👍
Very well explained….well done
👍
Great video nice one mate . Electrician doing plumbing that's one job I need to do again! Luckily I didn't glue it first time around
Nice one
Good vid buddy!
Thanks a lot 👍
Brilliantly explained. However, we are re arranging our kitchen which means the soil stack entry will only be a meter from our sink is it ok to be that close? I'm just wondering in case of any stench back flow. I'm guessing the water trap will prevent this bit just checking before I go about it. Thank you for this, I am a follower as of today👍
Very helpful Cheers
Great, but don't you need to rough up the inside of the boss to provide a key for that side of the joint, or is it supplied prekeyed
Solvent weld needs both pipes to be solvent weldable, not all plastic water pipe is the same.
After having a few accidents and cracking pipes I actually found that once the pilot is drilled actually going backwards with the hole saw is a bit safer
Hi. Will the straps open enough to fit over the stink pipe. Also what size hole cutter for a 32mm waste pipe or are they all universal as in 57mm cutter in your video. Thanks
I recommend using gap filling cement rather than solvent weld. A bit more expensive but much more reliable.
Looks like it might be difficult to get the correct fall?
I wonder if it is safe to assume that the type of plastic used on the soil pipe is solvent weldable? Obviously in some situations that might not be enough of the pipe exposed to see any markings.
Can you add a basin waste pipe to a toilet stack ,because i thought they hav to be separate
Can you add Another toilet waste pipe into existing one the same way??
Would this be suitable once fitted, to be installed under a tiled floor?
I need to move a sink waste - which currently runs directly straight down into the top hole of a 110mm soil stack (with a cap that has a 32mm hole). Which is in a concrete floor. I need to run/move the waste 30cm to the side (into a corner, for corner unit). So can I channel into the concrete floor and run the 32mm pipe into the side of the soil stack using one of these, and then concrete back over the pipe/channel?
Hi. Can you use a strap boss on the pan connector that comes off the back of the toilet?
What do you do it it leaks afterwards?
Class
bestbof best
Hi will this fit on cast iron pipe thank you ?
I've got the same question. Did you get an answer?
@@BingTiddleBong no lol
Where can you buy these in Canada?
You don't need to glue them the strap is there for a reason
how to remove or replace the Strap boss to connect wast pipe?
No mention of what size hole to drill.
Forgot to mention existing one is weeping 15 year old is replacement only solution
Do the bosses accept solvent weld pipe with them being a bigger diameter? Thank you
Yes they do
Wait...so you're telling me that my plumber is a total mong?
He said i can't run my bath waste to to soil pipe.
What a prick.
Him not you lol
😂