KuKirin G2Pro - Introduction to P parameter settings (with English subtitles)
HTML-код
- Опубликовано: 19 сен 2022
- The KuKirin G2Pro is an upgrade and optimisation of the KugooKirin G2Pro. Improved display, electric door lock, controller, light board module. These minor changes do not affect the mechanics of the scooter or the user experience at all. They are small changes that our factory makes every time the model goes into production based on customer feedback.
-------------
1. Insert the key and turn it to the right to turn on the scooter. Press and hold the [on/off] button to switch the scooter turn on and off.
2. After turning it on, press the [on/off] button once briefly to change gears, in three steps.
Press the [on/off] button 3 times in succession to enter the menu setting interface.
P1: Speed and mileage unit setting, 0-km or 1-mile. default km/h.
Press and hold the [on/off] button for 3 seconds, the value will flash; at this time, you can short press the [on/off] button to select 1-mile or 0-km; when 0-km is displayed, select km, Km/h will be displayed; when 1-mile is displayed, select mile, mile will be displayed; then press and hold the [on/off] button to exit and select other parameters for debugging; if there is no operation 8 seconds later, the parameter setting will be automatically exited (the same operation for other parameter settings). After entering the menu setting, if the current parameter does not need to be modified and set, switch to the next parameter setting interface after short pressing the [on/off] button once.
P2: Voltage level setting: 36V/48/52/60V/72V. Default 48V, no need to adjust.
(it is lower than the normal value of 48V, even if the display is full, the scooter is not actually fully charged. If it is higher than 48v, the battery level may display abnormally.)
P3: wheel diameter setting is based on the tire size of the scooter: unit=inch; can be set to 080-160 (080 means 8'', 100 means 10'', and so on), increasing by 5 each time.
the KuKirin G2 Max wheel is 10'', then the default wheel diameter setting of G2 Max is 10, and the Kirin G2Pro wheel is 9'', then the default setting of the Kirin G2Pro wheel diameter is 9, which does not need to be adjusted.
(If the wheel diameter is adjusted to a value other than the default wheel diameter, the speed displayed when the scooter ride will be inaccurate.)
P4: number of speed measuring poles: is set according to the number of magnets in the motor. Kirin G2Pro and G2 Max have 30 magnets, so the default value of p4 is 30. range: 1-100, default 30. no need to adjust.
P5: Cruise Control setting: 0 to cancel cruise control, 1 to set the cruise control. when cruise control is turned on, the cruise control icon flashes; default cancel cruise control.
Cruise control mode: The scooter is set to cruise control mode. Press the accelerator to ride. After the accelerator is released, the scooter will continue to drive at the current speed without pressing the accelerator.
(Kindly Tip: Please pay attention to safety when using this cruise control mode. The cruise control still will continue to ride when the accelerator is released. To stop, you need to press the brake.)
P6: Start mode setting, 0=zero start; 1=non-zero start, the start mode is displayed when the power is turned on (zero starts will not display the icon, non-zero start displays NON).
Kindly notice that after the power is turned on, press the throttle in zero start mode to start directly; in non-zero start mode, the scooter needs to be coasting above 5km/h before it can be started.
P7: Speed Limit setting: range 0-100 percentage speed limit. 99 is to cancel the speed limit setting and ride at the normal speed of each gear.
P8: Hibernation time setting: 0, no hibernation; other numbers are hibernation time, range: 1-60; unit minutes, default 5 minutes; By default, the scooter will automatically shut down if there is no operation for 5 minutes.
PA: Start Strength Setting, which is the starting drive strength when the throttle is pressed after switching on: range 1-5. 1=min, 5=max; default 5.
The default setting for both the Kirin G2Pro and G2 max is 5. You can adjust this setting to suit your needs. If you feel that the start-up force after pressing the throttle is too strong, you can adjust it downwards.
(Assuming that the current Start Strength is 5, the scooter will go from 0km/h to max speed in 5 seconds. If you adjust it to a different value, the process will take longer, to 10 seconds or something like that. (These times are not actual, just an analogy))
PB: Brake Strength Setting: default 0, No Adjustment is required. (because the kirin G2Pro and G2 Max both models are disc brakes, and the main braking is still controlled by the customer himself by pressing the brake lever)
PC: ODO clear. Unrecoverable after being cleared. 0 - The mileage data is maintained and not cleared. 1 - The mileage data is cleared and reset to zero. If set 1, automatically exit the parameter setting page, and clear the mileage data, which cannot be restored.
Just bought g2 pro. Amazin scooter!
Р1 - Налаштування швидкість та пробігу ,0км або 1 миля км /год за замовчуванням.
Р2 - налаштування рівня напруги: 36в,48,52,60,72В за замовчуванням 48 ,не потрібно регулювати
Р3 - діаметр колеса:одиниця =дюйм; можна встановити 080 -160 (080 означає 8,100 означає 10,і так далі збільшуючи на 5 що разу.
Р4 - кількість полюсів вимірювання швидкості : діапазоні : 1 - 100, за замовчуванням 30. без регулювання.
Р5 - налаштування круіз контролю: 9 - скасування круїз-контролю, 1 для налаштування круїз-контролю.
Р6 - налаштування режиму запуску, 0 - нуль початок; 1 - ненульовий старт.
Р7 - налаштування обмеження швидкості : діапазон 0 - 100 відсотків обмеження швидкості. 99 - скасувати налаштування обмеження швидкості та їзди на звичайній швидкості для кожної передачі.
Відрегулюйте значення параметра на 50, тобто обмежте швидкість кожної передачі до половини.
Р8 - налаштування часу сну: 0, сплячий режим відсутній:інші числа - час сплячки, діапазон: 1 - 60; одиниця хвилин, за замовчуванням 5 хвилин.
РА - налаштування початкової сили: діапазон 1 - 5. 1=хв ,5 = макс, за замовчуванням 5, коригування не потрібно.
РВ - налаштування сили гальмування : за замовчуванням, регулювання не потрібне.
РК - ODO чистий. Не підлягає відновленню після очищення. 0 - дані про пробіг зберігаються і не очищається. 1 - дані про пробіг очищено та скинуто до нуля.
Автоматичний вихід зі сторінки!
Hi
you problably saved my life.
Hi! Wich one is more faster the g2 max or the g3??
How can I adjust the belt without pushing it?
how to adjust front shock absorber on kukirin g2 max. he's too hard
Works whit the m5 pro too?
why is the display changed is this the old or new display? the wide display in the Tech4All video was better
English subtitles???
Just turn on the youtube auto translate. Works good enough
It's great video but I have g2 pro but i have other display.
How do you take the speed restriction off and change it so it can as fast as the scooter can go thanks
KuKirin G2Pro&G2 Max - P07: Speed Limit Detailed Adjustment Tutorial (speed limit 20&25km/h) ruclips.net/video/Q5LNlEIyOWA/видео.html
Hi. I have bought a G2 pro, I set the P5 cruise control but does not work. Does it have real cruise control or it is in the menu only, but no cruise control built in the scooter? Thanks
G2 pro wich one? Kugo or Kukirin?
If I Change the P2 voltage from 48 to 72, will it go faster ?
was wondering the same thing
They explain how to change the voltage, but not what that does. What is the effect of changing the voltage?
Dont change the voltage. If you put it too high your battery can explode! I would recommend to keep it at 48v.
thank you now i can always reduce power when i see cops around :D¨
ACAB 😂
@@user-tp5bz9rn2o actualy stoped doing that i just ride and when i see them il slowdown. they cant do anything unless they get catch me riding faster. and that amost hapend at monday but thankfuly i was riding 30km/h at that time xD and they dint care
Is it have regenerative/recuperating electric brake?
No
What is the difference from 48V to 72V
You should don't change IT because 48v id voltage of battery and if u change it may cause damage to your electric scooter
How to turn on the start of movement mode without a push kukirin m5 pro
For KuKirin M5Pro scooter: After switching on, press the [switch] button 3 times in succession to switch the start-up mode.
Scooters have two starting methods: zero starts (static start) and non-zero start (sliding start) model.
In zero start mode, press the accelerator to ride;
In the non-zero start mode, pressing the accelerator fails to ride, the scooter needs to be coasting above 5km/h before it can be started. you need to use your feet to help the scooter slide a certain distance.
@@kugookirineu Zero start is not activated by triple pressing. I can't turn it on
@@kugookirineu You can remove the video instruction settings kukirin m5 pro
Здравствуйте как войти в меню бк
3секунди кнопку подержи
Subtitles Please !!!
Sorry, there may be a problem somewhere, you can refresh it.