Thanks for posting this. I have my 100-hour service due on my F200. Is there a specific Yamaha grease required or just any marine grease for the shaft?
@@jaybee006 lucas marine grease is the best to use in my opinion if you can get it. Last time i greased the fittings i couldn't find it so i had to use another. Thanks for watching. If you need any help let me know.
I did look at it before removal. But I didn't make a comment on it. Because the new one doesn't matter without the fin. It only fits in one way. There's no fin to detect tracking.
Hi Andrew. A million thanks for watching the video and spending your time on my channel. So I did finally get the lower unit off if I'm right on what you are referring to. I did find and remove the bolt under the anode, which I'll go back and review but I thought I did show that bolt. but it was a bear getting the lower unit loose and the camera shut off just at the time it cut loose, but I didn't realize it had. So on my next time I replace the water impeller, I definitely will show that. Appreciate your comments. I hope that answered your request. If I can do anything else, please let me know. Tight lines....
Andrew, I just looked back on that video and I definitely showed that bolt and removed it in the very beginning of the video. Check back on it whenever you get a minute . Again, thanks for pointing that out. I do appreciate anyone catching something that I might of missed. It only helps me do better
Excellent detail! Good job.
Great Video & VERY INFORMATIVE. 🎣👏😉👏🎣
Nice home repairing
Do you have part numbers for the part that goes over the 3 washers and the piece that goes over that? You had to pry on it to get it off. Thanks.
Hunter let me look. I'll add them to the description if I do,but I won't have time until tomorrow. Thanks for watching.
Yamaha Genuine OEM Spacer & Collar Set
Spacer
OEM Part # 61A-45538-00-00
Collar
OEM Part # 61A-45527-00-00
I don't have the three washer part number. I used the ones that were on the shaft already. I'm sure you can order them from your local yamaha dealer.
Nice video.
Thanks for posting this. I have my 100-hour service due on my F200. Is there a specific Yamaha grease required or just any marine grease for the shaft?
@@jaybee006 lucas marine grease is the best to use in my opinion if you can get it. Last time i greased the fittings i couldn't find it so i had to use another.
Thanks for watching.
If you need any help let me know.
@@jaybee006 also for your information this 100hr service i have two videos. So to look at all of it see part 2 also to finish the complete service.
@@oceandeepfishing4555 Yessir, I have watched all three (oil change from 20 hour service, Part 1 and Part 2 from the 100-hour service). Very helpful!
You missed the alignment of the anode before removal
I did look at it before removal. But I didn't make a comment on it. Because the new one doesn't matter without the fin. It only fits in one way. There's no fin to detect tracking.
You should go back and show everyone how you finally got the leg off. you missed the bolt under the anode I believe.
Hi Andrew. A million thanks for watching the video and spending your time on my channel.
So I did finally get the lower unit off if I'm right on what you are referring to. I did find and remove the bolt under the anode, which I'll go back and review but I thought I did show that bolt. but it was a bear getting the lower unit loose and the camera shut off just at the time it cut loose, but I didn't realize it had.
So on my next time I replace the water impeller, I definitely will show that. Appreciate your comments. I hope that answered your request. If I can do anything else, please let me know.
Tight lines....
Andrew, I just looked back on that video and I definitely showed that bolt and removed it in the very beginning of the video. Check back on it whenever you get a minute .
Again, thanks for pointing that out.
I do appreciate anyone catching something that I might of missed. It only helps me do better