I want to know about how much time motor continuously working and when does voltage get drop below 12v? What is change of behaviour of motor after reaching the voltage below 12v dc? How much long 12v peak voltage remain while working with single and dual motor?
I have this PWM controller and RS775 motor, i want to control the speed of the motor through arduino's pwm signal. How can i do this using the PWM controller?
Check first, that ur panel is giving minimum 12v 4a. Otherwise it's difficult for controller to push small watts to run the motor. B'coz that big boy do require huge power!!!
Check first, that ur panel is giving minimum 12v 4a. Otherwise it's difficult for controller to push small watts to run the motor. B'coz that big boy do require huge power!!!
Hye if i wanna put dc booster . Should i wire the controller after the booster to the motor or Wire the controller first - booster then straight to the motor . Tq
what about reverse spinning without changing wiring position. There should be just some knob which if turned left it should spin counter clockwise and when turned right it should spin clock wise. How to achieve that?
Hey, I am new at this -- I have a 24V max 775 and I have it hooked up to an AC/DC power controller that outputs 3-12V at 2A, the motor is running fine and working to move my load, but when I go to measure the voltage at the motor there is a drop in voltage from the dial voltage. If I turn the speed controller to output 3.5V I am reading 2V at the motor with my multimeter. Can you help me understand this?
Hey I have a question Recently I bought 12v motor speed controller from eBay My motor makes noise at the lower speed When check the voltage with multimeter I find out that the speed controller changes voltage not amp Is this how we supposed to be ? And if I want to change amperage output not voltage is there any solution to that ? Or I just have to deal with the noise?
If you using pwm, it did not change voltage (may be the voltage drop slightly). You may be bought speed controller that alter voltage output. That is why a motor makes noise at lower speed. You should PWM speed controller.
It is the first time that i have contact with dimmer, and i am head banding. I did the same sequence as the wiring, but nothing about the climate control fan. Energy enters the dimmer, but it does not. Was it unlucky to buy a faulty dimmer?
@@LahisTechLT pls tell me, let's say i connect the dc motor to a water pump with unregulated power source of 12v, the motor can turns the turbine continuously with no problem. but since i want to regulate the volume of the water flow out of the water pump so that it does not pump out so much volume of water, hence i will dial the knob down so that the motor runs slower.. now the question is, when the motor runs slower , does output torque to the motor also decreases ? can it still now turns the turbine of the water pump ? to push the water up ? i want to make a project require the knowledge of this, in order to know if this pwm speed controller for the dc motor suitable for my application or not. thx andrew
@Abdel Rahman Yasser he said in ciamis (one of city in java island, Indonesia) it's hard to find ac or dc dimmer. Actually it's easy to find them in local online shop.
I build grass cutter My motor 775 12v _ 150w getting hot and burn a wire , because I run with out speed controller , if I use speed controller that will help ?? please get back to me soon thank
Yeah you need either a speed controller like this or change the power source to a lower amp. I will upload a new video tonight about a power adapter,which suits for your application.
@@philliple288 Oh, I see, you said your power input is 150W right? So then it gonna be an issue for this PWM speed controller, because if your motor takes any load greater than 10A this module can't handle. You need to take a higher amp PWM controller. Btw, what's your application? Try using thick wires (18AWG or 16AWG) , don't use thin cheap wires.
@@LahisTechLT Please help I was use 16 AWG wires it is still getting hot so, I stooped and run one more time , my motor 775 12V - 150W , 13000RPM I use battery 12V 9AM , I did order speed controller(( 10 AM )) do you thing that is good enough ? , and change the wire 14 or 12 AWG ? after that I will let you know what going on okay I need your help
@@ariell4416 I use 20 gauge solder on small wires. solid, not rosin core or flux core. use paste or liquid flux, make sure wires clean. sand paper on pin and wire if need to. it takes a little practice to make neat connections. it's easy
Rpm nya gk terlalu besar bro krna gk tegangan aki nya gk sesuai dgn volt motor dinamo nya, klo mau tambah power tegangan nya lagi biar makin besar putaran Rpm nya..
Hi😄 but this speed controller can stepup the voltage or if your battery is of 12 v for example, this is the max voltage you can use? Thanks so much. Alex
I want to know about how much time motor continuously working and when does voltage get drop below 12v?
What is change of behaviour of motor after reaching the voltage below 12v dc?
How much long 12v peak voltage remain while working with single and dual motor?
Hello, thanks for the video. One question, can the engine be used at low rpm for a long time without overheating?
Thanks again
What is the exact 12vdc battery back up time while working with single and double motor.
What does the little jumper near the pot do
thank you
Awesomely simple
Nice tutorial, now I know how to use my 775 motor
Thanks
Bhai isme ebike ka accelerator lga sakte hai kya ??
Hai LahisTech, may ask, is there possible if i add on off/on off on switch between dimmer and motor? Thank you
yes
Woou greats... how many watts have this motor?
I have this PWM controller and RS775 motor, i want to control the speed of the motor through arduino's pwm signal. How can i do this using the PWM controller?
Can I use it without any battery? Directly wire from solar panel to controller to motor? If so, what can you recommend best for it. Thanks
Check first, that ur panel is giving minimum 12v 4a. Otherwise it's difficult for controller to push small watts to run the motor. B'coz that big boy do require huge power!!!
Check first, that ur panel is giving minimum 12v 4a. Otherwise it's difficult for controller to push small watts to run the motor. B'coz that big boy do require huge power!!!
Hye if i wanna put dc booster . Should i wire the controller after the booster to the motor or
Wire the controller first - booster then straight to the motor .
Tq
Vhi 775dc motor ta12v 8Ah dea chala heat krtasa
Kano vhi?
Ami kto amp battery use krbo fan banata?
Lgatar kitne der chalegi 1 ya 2 ghnte
Bhai please reply isme ecycle ka throttle kese lagega
Brother a question
With this dimmer / moduler ... 775 motor speed can increase or not?
Bisa untuk pengganti potensio tangki semprot elektrik g om pwm nya
what about reverse spinning without changing wiring position. There should be just some knob which if turned left it should spin counter clockwise and when turned right it should spin clock wise. How to achieve that?
A polarity reversing switch
Hey, I am new at this -- I have a 24V max 775 and I have it hooked up to an AC/DC power controller that outputs 3-12V at 2A, the motor is running fine and working to move my load, but when I go to measure the voltage at the motor there is a drop in voltage from the dial voltage. If I turn the speed controller to output 3.5V I am reading 2V at the motor with my multimeter. Can you help me understand this?
Bhai ye 24v 2 rpm adapter se chalega
Can this motor control a small cycle. Please tell me
Mas dari psu langsung ke modul itu bisa
Tell me where u connect 40v.10 a👀👀
Hey I have a question
Recently I bought 12v motor speed controller from eBay
My motor makes noise at the lower speed
When check the voltage with multimeter I find out that the speed controller changes voltage not amp
Is this how we supposed to be ?
And if I want to change amperage output not voltage is there any solution to that ? Or I just have to deal with the noise?
If you using pwm, it did not change voltage (may be the voltage drop slightly). You may be bought speed controller that alter voltage output. That is why a motor makes noise at lower speed. You should PWM speed controller.
Best bro🤜, kitna kharcha hoga i want this set👈🙏🙏plz
Is that max pwm power same with direct connect to battery? I've pwm same as you but i got that problem
lol u just same person
GOOD
এই সারকিট কোথায় পাওয়া যাবে ভাই জানালে খুশি হতাম
What about circuit on the full load ?
It works fine.
Those 775 motors sound like a V10 Engine lol
Max how much degree it rotates bro.. please reply me
360
how many amps the motor draws with vs. without pwm at low rpm (start and stop)?
150watts
what can be used to electric current 220v
Apa bisa di gunakan ke arus listrik
This is for DC only, like automotive applications. For AC you need a variac (large and heavy) or an SCR based speed controller which can switch AC.
Will it work with 50ah battery
Are you have speed controller for AC motor and how much it's cost
Motor running hours ?
yeah..
LahisTech thanks
@@briandinh3229 it works upto 40V 10A
It is the first time that i have contact with dimmer, and i am head banding.
I did the same sequence as the wiring, but nothing about the climate control fan. Energy enters the dimmer, but it does not.
Was it unlucky to buy a faulty dimmer?
Yes
Can i use 10 amp continou for 5 hour?
It change the voltage output?
kitne Price ka hai power supply
I have a printer adaptor 24v 2amp, this is match for dc controlled diymore to use my 12to24 volt 775 motor?
yes, it can supply 40V 10A
Thank you very much :-)
When i turned to highest speed suddenly stopped its take to 20 to 30 seconds it will open again?
May I get this
Can i use dc motor for my bycycle
edu salam pro which bicycle? which motor? i’m confused!
My bycycle with dc775 12v motor
@@techlife3773 hopeless, this motor is not powerful enough for a bicycle.
Yes but wear a helmet for safety
what wire typeing for blue
Malem mas, tolong mas, transistor yg ada pendinginnya itu tipe brp?soalnya punya saya kakinya putus dan tipenya gk terbaca.
Terimakasih.
Nanti ya gan.. saya lg barusan pesan entar kalau udh datang entar aku lihatkan mas type brp
Can i use 12v-6AH power supply??
Yes
Potensio semprotan di ganti itu bisa gk bang
Barapa hrga
Can this control speed of AC motor also
No
Itu bisa buat mengatur kecepatan dinamo sepeda listrik donk
ভাই এই রেগুলেটরটির দাম কত? জানাবেন প্লিজ?
How many ohm valuable resistor does it use..?
PLZ.. I have to know..
I think, you asked me the value of that potentiometer right?
The potentiometer should be 100Kohms if I'm not mistaken.
@@Yonatan24 Yup it's 100K Ohms.
100K Ohms
@@LahisTechLT
pls tell me, let's say i connect the dc motor to a water pump with unregulated power source of 12v, the motor can turns the turbine continuously with no problem. but since i want to regulate the volume of the water flow out of the water pump so that it does not pump out so much volume of water, hence i will dial the knob down so that the motor runs slower..
now the question is, when the motor runs slower , does output torque to the motor also decreases ? can it still now turns the turbine of the water pump ? to push the water up ?
i want to make a project require the knowledge of this, in order to know if this pwm speed controller for the dc motor suitable for my application or not.
thx
andrew
If use dinamo 100 wat...what a dimmer can be use?
which dimmer?? There is no dimmer here.
Bô chinh toc đô đo chay mây vôn , mây ambe v ad
Di ciamis sulit mencaridimer ac maupundc
@Abdel Rahman Yasser he said in ciamis (one of city in java island, Indonesia) it's hard to find ac or dc dimmer. Actually it's easy to find them in local online shop.
I build grass cutter My motor 775 12v _ 150w getting hot and burn a wire , because I run with out speed controller , if I use speed controller that will help ?? please get back to me soon thank
Yeah you need either a speed controller like this or change the power source to a lower amp. I will upload a new video tonight about a power adapter,which suits for your application.
I order speed controller like this already , like you said is Okay to use ? the wire will not getting hot no more
@@philliple288 Oh, I see, you said your power input is 150W right? So then it gonna be an issue for this PWM speed controller, because if your motor takes any load greater than 10A this module can't handle. You need to take a higher amp PWM controller. Btw, what's your application? Try using thick wires (18AWG or 16AWG) , don't use thin cheap wires.
@@LahisTechLT Please help I was use 16 AWG wires it is still getting hot so, I stooped and run one more time , my motor 775 12V - 150W , 13000RPM I use battery 12V 9AM , I did order speed controller(( 10 AM )) do you thing that is good enough ? , and change the wire 14 or 12 AWG ? after that I will let you know what going on okay I need your help
@@philliple288 Yeah, with that it should work fine. Does your motor a new one? 12V 9AH Battery with 10Amp PWM controller is matching perfectly.
It is smookeless stove.
Can we use pwmcontrol with Battery
100am ?
azad ranya upto 10A only
Does it match for 895 DC Motor? Or it is required some upgraded part??
Perfect for 895 motor
I don't use adaptors or battery
Can be to use the electrical plug at home
not good. this controller is not rated for high voltage or currents
@@pauls5745 i want solder wire so how diameters suitable for solder wire 0.6mm/0.08mm?
@@ariell4416 I use 20 gauge solder on small wires. solid, not rosin core or flux core. use paste or liquid flux, make sure wires clean. sand paper on pin and wire if need to. it takes a little practice to make neat connections. it's easy
Mau tanya kalo dinamo 24 volt pake aki 14 v bisa tidak
Rpm nya gk terlalu besar bro krna gk tegangan aki nya gk sesuai dgn volt motor dinamo nya, klo mau tambah power tegangan nya lagi biar makin besar putaran Rpm nya..
How can we stop that buzzing sound when low cycle?
I saw when you accelerate max the buzzing sound stoped
Mau beli alat potensio dc 12
Hi, Can I use a 775 12v with a source 24v? Tks!
Yes superfast
Hi😄 but this speed controller can stepup the voltage or if your battery is of 12 v for example, this is the max voltage you can use? Thanks so much. Alex
no it doesn't step up the voltage. It works 0-40v 10A and pwm output provides according to the remaining battery voltage.
@@LahisTechLT can go on..like 5-12v on it's output?
can the music and add commentary...
how many rpm?
At max 16000 rpm
If I give 12v in, then can I get i.e. 24V out?
Hi frnd
From which shop I bought pwm
Jeetsingh Dagur AliExpress
can you please give me it's schematic
Hi, This is a 2 layer PCB; also not my design, You can purchase it few bucks on Ebay, Bangood.
i need 100 pcs pcb 1 leyer ( motor speed control)
এই কন্ট্রোলার দাম কতো
الموسيقي موزعجة جدا
এটা কি আছে
Nontechnical procedure.No standard of expriment.
voltase🤔🤔🤔🤔
মোবাইল নাম্বার দেন
775 motor very slow rpm
Shinley nope
This PWM Only Wasted Money Can't Use For Dc Motor 775
Need 60-100A PWM
It works fine with 775 motor
Thanks
Hello is this item compatible in DC 12v 3.4A cooling fan using a power bank?