Would you be able to comment on your tips about the gears/transmission and how to make it spin so freely? I see that there's some addition to the yellow gear, though it's hard to see in the video and the captioning isn't able to translate to english. Thanks in advance!
Hi, thank you commenting! Its a small washer, the thing you saw between spur gear and crown gear. "Selection" with best parts that will turn smoothly (gear, shafts, wheels etc.) Will help you improve the overall performance of the machine
Round hole ball bearing sa gulong. Small dia carbon wheels pierced. 13mm dar silver. All HG tamiya plates. Carbon x chassiz plate sa rear bottom.3.5.1 gear. Rare. Carbon AR ..Mga dampers. High mount sa harap. Colored lock nuts. is this good enough.?
When inserting 8T pinion gears to motors. You need to exposed shaftheads for at least 0.5mm. With this, you can prevent contacting gears. And also, according to Tamiya official rules, AR chassis and Fm-A chassis machines must use brass, Black or reinforced pinions (15454, 15438).
Hi sir, check this video from facebook page🙂. Im not sure if its safe to share links😅 m.facebook.com/story.php?story_fbid=pfbid02LY2VymzDQV6YAoXJpJbv27uaX33XWGfzcLQAKZdaJV186T518L5MFMQqkBysUFJFl&id=100075801260835
Thankyou po sa helpful vids mo. I didnt know na pinoy ka hehehe. Anong pong gagawin 8:10 pag hndi gnyan ikot ng wheels ko kahit may 620 bearing na? 🥲😅🤣 di po sya ganyan naikot eh hahaha
@@minivictorydonkey aling microlon po ang gamit niyo? Kase baka po walang mismong microlon dito sa toronto eh hehe. So if incase po ibang brand gagamitin 😁 and can you also link me up on one of your video po that you did put the microlon process? I watched one of it last week eh. 😅
Newbie and new sub here paps, ask ko lang sa fma chassis currently yung under ng front bumber sakin ang nakalagay 1pc na reinforce plate. Yung 2nd reinforce ilalagay ko sana kaso tumatama dun sa una or pumapatong. Pano po kaya sya malalapat? Pede ko po ba lakihan yung hole ng reinforce plate? Salamat po
Hello sir, thank you for commenting, may upcoming video po ako about sa build, everything will be explained in details including sa front brakes. Wait lang po konti, pasensya na po😔
@@minivictorydonkey sa Musashi Kosugi ako idol. medyo malayo pla tau. sana nag pang punta ka minsan malapit sa amin lalo na pag weekend. laro tau sa Tressa Yokohama ng maturoan mo din ako idol hehehe.
Yun oh! Ito po yung hinihintay ko Sir e
Grabe dami ko natutunan sa channel mo. Maraming salamat! Nka FM-A din ako kaya laking tulong toh
Thank you sir and good to know na nakakatulong mga video ko. Sana makapaglaro din tayo in the future sa events😊
Solid thank you po sa tutorial
New sub here 🙌
Salamat sa video mo idol!
New subscriber here 👍👍
New sub here
Hello po sana may guide din kau sa pag set ng mass dampers for different track lay out
fighting oppa angas haha yung isa fighting ajumma?
Would you be able to comment on your tips about the gears/transmission and how to make it spin so freely? I see that there's some addition to the yellow gear, though it's hard to see in the video and the captioning isn't able to translate to english. Thanks in advance!
Hi, thank you commenting!
Its a small washer, the thing you saw between spur gear and crown gear. "Selection" with best parts that will turn smoothly (gear, shafts, wheels etc.) Will help you improve the overall performance of the machine
What are your thoughts about 19mm rollers in front bumper? Would you recommend?
I only recommend 19mm front rollers to 4 lanes track, but I will try to test it.
New subs here lodi 🎉
- Tagalog lang sana palagi :)
Hi there, can I know what wheels are those?
Wow! Pinoy!
Up dito
Ok ba lowfric tires sa likod ng fma?
boss anung mga oil ang gamit mu dito sa japan? salamat
Sir meron ka ba full build video nitong fmA bmax mo? Need ko lang po ng inspiration.
Edit: ah, nakita ko na.
sir anu thickness sa mga ba k plate
sir, ask lang, ano po name nung color black sa labas ng mga wheels mo? Pang lock po ba yan? Salamat po
Round hole ball bearing sa gulong. Small dia carbon wheels pierced. 13mm dar silver. All HG tamiya plates. Carbon x chassiz plate sa rear bottom.3.5.1 gear. Rare. Carbon AR ..Mga dampers. High mount sa harap. Colored lock nuts.
is this good enough.?
How to setting balancing wheels? Share please...
Hello sir, will try to on the next video
Can't wait 😊
thicknes sa back plates?
hi. i see u using carbon reinforced pinion. does your counter gear got damage?
When inserting 8T pinion gears to motors. You need to exposed shaftheads for at least 0.5mm. With this, you can prevent contacting gears.
And also, according to Tamiya official rules, AR chassis and Fm-A chassis machines must use brass, Black or reinforced pinions (15454, 15438).
sir how did you do your front roller setting, kinda confused with the lock nut there
Hi sir, check this video from facebook page🙂. Im not sure if its safe to share links😅
m.facebook.com/story.php?story_fbid=pfbid02LY2VymzDQV6YAoXJpJbv27uaX33XWGfzcLQAKZdaJV186T518L5MFMQqkBysUFJFl&id=100075801260835
@@minivictorydonkey uy maraming salamat po, I managed to do the front roller setting a different way but thanks for the link!
does the yellow gear has a bearing? i see metal close to the shaft...
Hi sir, what youre seing is a small washer. Bearing is impossible to fit between spur gear without modification.
Interesado ako sa M.A. Chassis Build mo lodi... bka pede makakita ng lap time at more build tip sa M.A. chassis thanks more power
Thank you sir for commenting
I will try my best to get time for making a video for MA B-max. Been too busy recently.
lodi master sama mo n rin cost hahahah @@minivictorydonkey
Nabibili po ba yung washer sir?
Pinoy pala hehe
lods pede malaman magkano nagastos mo sa kulay red na chassis?
Is it ok to glue 2 the same frp stick together ?
Yes sir, it became more stronger from bending and damage
hope there is subtitle :)
sir what wheel size did you use?
A-spoke medium wheels
Panu po magpa tahimik ng ingay ng motor po
Thankyou po sa helpful vids mo. I didnt know na pinoy ka hehehe. Anong pong gagawin 8:10 pag hndi gnyan ikot ng wheels ko kahit may 620 bearing na? 🥲😅🤣 di po sya ganyan naikot eh hahaha
Hi sir, thank you for comments.
Naka aligned na po kasi ung shaft, wheels and tire. Microlon coated na din ung bearings🙂
@@minivictorydonkey aling microlon po ang gamit niyo? Kase baka po walang mismong microlon dito sa toronto eh hehe. So if incase po ibang brand gagamitin 😁 and can you also link me up on one of your video po that you did put the microlon process? I watched one of it last week eh. 😅
Pwede ilapag lahat ng mga parts nya hahah
Pwera lng sa gears motors
Kakasimula kupalang subukan kong gayahin tong build nato same mach frame pero standard lang yung akin. 4:40
newbie question sir.: ano usual height ng brakes from the track?
hi sir, it depends on the tire diameter. My medium tire should be around 3mm clearance and 2mm for a small diameter.
Saan ba dapat naka lagay ung 12mm dia ng dar sa taas ba o sa baba?
In my case, sa baba lagi pero binabago ko depende sa sitwasyon
Boss new sub here. Tanong ko lang kung anong brand and model at size ng case na pinaglalagyan mo ng kotse? Meiho ba yan? Salamat
Hi sir, Nabibili po yan sa Daiso or Seria, 110yen lang🙂
Newbie and new sub here paps, ask ko lang sa fma chassis currently yung under ng front bumber sakin ang nakalagay 1pc na reinforce plate. Yung 2nd reinforce ilalagay ko sana kaso tumatama dun sa una or pumapatong. Pano po kaya sya malalapat? Pede ko po ba lakihan yung hole ng reinforce plate? Salamat po
Hello sir, thank you for commenting, may upcoming video po ako about sa build, everything will be explained in details including sa front brakes. Wait lang po konti, pasensya na po😔
Bro matanong lang, ano po yung gamit nyo sa Bmax class para sa front plate angles since di pwede gumamit ng tabas na angle plates
Washer lang gamit ko pag need ko magdagdag ng angle
Nasisira FMA chassis ko sir pag walang movement masyado yung propeller shaft. Nahuhukay sa rear part 😢
Hi sir, kung mapapansin nyo dun sa tutorial ko, nilagyan ko ng markers ung portion ng propeller shaft at chassis kung saan umiikot.
Yun ang parang pinaka fix niya?
idol..
ask lang po.. sa bmax set up..goods po ba na naka sliding damper yung front and rare.?or kahit front lang.?
thanks in advance po.🔥🔥🫡🫡
Hi, front is enough sir. It actually give you more control especially from approach+slope section
@@minivictorydonkey thanks alot sir..
planning kasi ako bumalik ..last race ko is year 2008..kaya iwan ako ngayon sa set-upan
@@minivictorydonkey btw..how can i reach you out.?do you have fb page sir.?mejo madami pa akong itatanong..kung tama o mali yung assemble ko po
San k sa Japan sir
Toyama sir
sir ung s spacer s gears. hnd q mxdo kita san m nilgy
Hi sir, sa pagitan ng spur gear at rib ng chassis
Yung machframe na black mo is 3.5:1 pero yung red is 3.7:1?
Yes sir😊
yung 3.7:1 mo po sir, washer-bearing-washer po ba? or bearing roller spacer-bearing-bearing roller spacer(94768)
Returner ako sa hobby after 10+ years, nag build ako ng fm-a starter pack. Any tips po regarding sa gearing?
Tires diameters ang gears may change depends on track layout, category and motors you are going to use. What is your prefer or style of class?
Tires diameters ang gears may change depends on track layout, category and motors you are going to use. What is your prefer or style of class?
Gearing towards bmax but first going to make it into a tmac setup
san ka sa Japan lods?
sa Toyama sir
@@minivictorydonkey sa Musashi Kosugi ako idol. medyo malayo pla tau. sana nag pang punta ka minsan malapit sa amin lalo na pag weekend. laro tau sa Tressa Yokohama ng maturoan mo din ako idol hehehe.
idol penge tamiiya po :D
boss san mu nabili yun plastic n lagayan mu ng tamiya nayan salamat
Hello sir, sa (100yen shop)Daiso or Seria, may white, black and clear kagayan ng nasa video🙂
@@minivictorydonkey salamat boss nakabili n ako nun isang araw, magndang gamitin lalo pag idedecorate ang tamiya hhehe
ask ko lang ulit boss anu gamit mung gear oil dito sa japan saka mga bearing oil, salamat po
Sir ano tawag dun sa ilaw?
Hi sir, "Hiromi Miraito", led lights
hello po newbie here in tamiya world pwede manghenge ng mga scrap parts kung okay lang po sana 🙏 gusto ko lang ng pang display sana mapansin 🙏
Hi sir, honestly I don't know how to respond to your comment. But if you can find me, maybe you will recieve something from me for free👍