Customizing Home Depot blinds to fit YOUR windows! | Home Essentials 2" Horizontal Blinds | 2021/41

My wife recently decided that the vertical blinds we installed throughout our home in 2014, have seen better days. Having three cats have taken their toll, plus the slats are beginning to grow brittle, and we are looking for a new look.
Our last home has Bermuda Shutters in the living room, and we really liked the look, but not the expense! So, we compromised on the Home Essentials 2" Faux Wood Horizontal Blinds from Home Depot. They had the look and feel of the Bermuda Shutters, without the price.
I started small to see, if she was going to really like them, so we designed to do the kitchen window first, it’s the smallest window on the first floor, and the blinds were only $40.00, so if we didn't like them, it wouldn't be a loss.
As many are aware, windows come in many sizes, blinds do not, while they come in standards sizes, the store can cut them to fit window widths, but not height. We took our measurements and headed to the nearest Home Depot, and picked out the size that would fit our window. We gave them the measurement of the opening, and it was cut to 1/2" in smaller. Never cut your blinds to the exact width, this will come back in a minute.
Returned home and removed the existing blinds. I installed the two brackets (the kit comes with three, but this opening was narrow and two was more that enough to support these blinds. Here is where we made our first mistake, we gave the tech at the store the height of the window, not the width, the blinds were too wide. Pre-made blinds have a maximum and minimum width. In my case the minimum width for these blinds was 35 1/2" the width needed was 34 1/4" fortunately there was a little play, and I was able to get the blinds re-cut to the smaller size, without having to repurchase another set. Whew.
Back home, the now shorter blinds snapped right in, and the task of cutting them to length was now at hand. This was the most time consuming of the process, had I not needed to cut the blinds, I would have been done at this point. Blinds come in standards lengths, 24", 27", 48", 64" and 72" in my case due to the width, the length was 64", my window is only 40" tall, so, I had to remove, multiple slats and shorten the strings.
The first step is to cut the retaining loops, being careful not to cut the retraction strings (the smaller taught ones), the remove the extra slats. Once that's done, you remove clip the horizontal "ladder" lines left, except the top one, this is where the bottom bar will stop at.
The blinds are self-retracting, so it was easy to raise them to their new height, tie the strings off, cut the excess, and tuck them into the buttonholes on the bottom.
Done, and even with the trips to the store, this project only took about 60 total minutes. Looks like I will be doing the rest of the windows in the coming weeks.
Thanks for watching Dad It Yourself!!!
*This post contains affiliate links and I will be compensated if you make a purchase after clicking on my links.*
Helpful/Affiliate Links:
Home Essentials 2 Inch Faux Wood Blinds by Bali: homedepot.sjv....
Tools I use in my shop: www.dadityours...
Support Dad It Yourself by shopping on Amazon: www.amazon.com...
Support Dad It Yourself by shopping at Home Depot: homedepot.sjv....
#Blinds #Home Depot #DadItYourselfDIY

[@floridaredneck]

If you remove and put the blade on backward, it will minimize chipping. I wouldn't cut those strings so close to the bottom; you can always stow them away in the hole. Keep about 4 or 5 intact. I moved my blinds when I moved, so you might need them longer in the future like I did. It's good to keep about three more slats on than you need for weight also (you'll thank me when you open your windows in the spring). That PMS sign above the window is kinda gross. I hope that wasn't the best sign in the store to buy.

[@DadItYourselfDIY]

Great advice!

[@allysonbooth4008]

Is it possible to fix this type of blind when one of the cords is frayed? I have melted the new cord to the old one and fed it through, but I can't figure out how to remove the spool, feed the new cord in, and affix it.

[@DadItYourselfDIY]

I'm sure with enough effort it could be. But there is a time/cost trade-off. Spending hours to fix a $50 set of blinds isn't economical when the time could be spent better elsewhere.

[@thebigdoghimself]

How does HD cut the width down? Do they use a miter saw or something with a fixed blade?

[@DadItYourselfDIY]

I would compare it to an enclosed radial arm saw. You cannot see the blade.

[@thebigdoghimself]

@@DadItYourselfDIY I've always wondered if the ends could be popped off and they could be cut at home with a high tooth blade.
I would use a sliding miter saw simply because you are pushing towards the fence vs. On a radial saw you are pulling outward. I am actually debating on if I should even keep my radial saw after getting a sliding miter saw.

[@DadItYourselfDIY]

There is an integrated clamp in their cutter. I'd be terrified of chipping.
I've never opened a radial arm saw, buy have two sliders..

[@knuckles1006]

THE STORE I BOUGHT MINE AT 20 YEARS AGO USED SHEARS to trim to length.

[@DadItYourselfDIY]

They have a specialized saw at the store to cut it.