I had longwire 30 years ago. What helped with getting a good signal was using a tapped coil with 12-way switch, which added various lengths to the longwire. Also a balun with earth helped match the impedance.
Thanks for video, brings back memories. I am a SWL, I had a DX 394 20 years ago until the grandkids mullered it by spilling water all over it. I had long wire made from old telephone cable. I made a simple antenna tuning unit out of a piece of broom stick wound with magnet wire which I copied from a radio book and it worked. One morning I received the South Island weather forecast from New Zealand to where I live near Dungeness. I was so surprised. I called all the people in the house to have a listen. I don't think Radio New Zealand broadcast on shortwave any more. I still love shortwave radio and listening all around. I received a QSL card from the Marianas Islands last year. They are north of Australia, so the bits of wire do work good sometimes. Thanks again for video again.
The 20 m wire is only half the antenna you need some ground radials in order to get anything reliably. If possible run a piece of coax all the way outside and then connect your wire as you've done but also connect several wires to the grounded part of the coax also known as the braid and you will improve your signal tremendously
Thanks for the great advice inbuilding your own Long Wire. I'm about to buy a screened copper wire (30Mts) and drape it all around the back garden, eventually will be connected to a battered old Tecsun S2000. Will get back to you here with the results.
Thanks for presenting your version of a quick and dirty, random wire antenna, you might enjoy greater sensitivity using the Hi-Z input on the DX394 (RCA on rear panel) instead of the Lo-Z (50 Ohm PL259 socket) input 👍 Additionally looping the connecting wires around each other then back on themselves (twisted) would vastly improve the mechanical strength of the join, naturally solder and heatshrink would provide improved weather resistance whilst also further adding to joint strength and added aesthetics 😊
ill give it a try. Solder a RCA connection to the wire then place it in the hi-z socket ? ive never used that socket on the radio. Maybe anther video coming up cheers
The DX394 owner's manual suggests attaching a long wire antenna to the "ANT HI-Z" plug on the back - you should that give you better reception that the SO239 input you used here - that's the "LO-Z" input, and it expects something like a dipole antenna instead.
Tell ya what Im gonna try when my rcvr finally arrives. I have a 100' extension cord on a spool. (I roll it out to mow the lawn and wind it back up when Im done) so why buy any wire. I can use an alligator clip to grab any one of the three wires on the plug and the braid I will also connect by alligator clip to a gnd wire from my out door faucet. If needed or desired I can "plug in" another extension cord to the end of the first one, and string em both along the top of my split rail fence. If needed (experiment) loading coils can be wound and alligator clips again used to connect. Since the wire is well insulated I could toss the end over the rioof to get the ant up in the air higher. BTW Alternatives Ive seen: (An article where) a "slinky toy" was used for a long wire. For a loop antenna, a roll of 25 wire ribbon cable stretched around a 55 gal plastic barrel with the ends connected together ONE WIRE OFFSET so s to create a 25 turn coil approx 30" dia. A dipole of two tape measures back to back pulled to what ever length you desire. I guess just let your mind wander and think outside the box. Lotta ways to skin a cat.
Awesome antenna quickie works fabulous on the DX 394 I love mine I think they are really underrated radios thanks for the idea I made one of your brilliant antennas but just used small electrical wire nuts to make connections. Thanks
it is surely working, I don't know if the receiver have a 50 ohm input impedence, I just guess it would be better to tune the long wire with a hf balun/autotransformer, with a 9:1 ratio, or more. It would good to make a 2nd part sequel
Very simple but effective temporary antenna. I enjoy doing experiments like thisand in the field with a portable. It is always surprising for sure. Thank you for sharing.
I will be building one of these next week. I want to get on the 40 meter band. The ground is still frozen so I will have to wait before putting the base for my vertical multi band antenna in.
STEVE HORNSHAW shouldn’t need to as your only receiving . If your receiver has a ground socket you can ground it by using a piece of wire from the gnd socket to the mud in your garden tied round a screw driver . But if your on the second or third floor it may act as a antenna you could also place it on copper pipe to ground it if need be
Great video. I have a shortwave radio that has a 3.5mm input jack. I have made a long wire antenna that uses an alligator clip to the whip antenna, but how can I attach a long single wire to a 3.5mm jack that I could plug into the 3.5mm antenna input?
I prefer analog if the Signal is very strong you can still hear it. On the digital radio if the signal isn’t very strong it just breaks up and crackles
Good, but how can you neutralize all the static electricity that the wire catches, before it goes into the receiver? I once did a simple antenna like this and on the connector I had powerful sparks..
Dont see why not as your receiving not transmitting. but you may find you get a lot more interference from the metal roof. the only way to see if you get interference is give it a try
good vid and good use of random wire for your long wire antenna, how well does the "inverted V" antenna do with this receiver or is that more of a use-by-use case type setup?
Good Day. I found this video while trying to find one for an antenna. I have a Radio Shack Pro-97 Triple Trunking 1000 CH Scanner, 20-527, Fire Police Air Ham. I would like to know if this would work for my scanner? Please let me know. Thanks.
This simple antenna will only work on hf bands ie short wave the higher the frequency the smaller the antenna the lower the frequency the bigger the antenna
Yes, it changes reception quality, but you have no chance of noticing it without costy proffesional equiptment like we have in my Radioclub. For this purpose like in video it's not important at all and you should worry about it.
🎉 Lovely vid! ❤
Finally someone SHOWING ALL THE DETAILS!
Cheerz from a Hungarian 🇭🇺 SWL (since the 90's) working in 🇬🇧
I had longwire 30 years ago. What helped with getting a good signal was using a tapped coil with 12-way switch, which added various lengths to the longwire. Also a balun with earth helped match the impedance.
Great information!!!!!
Thanks for video, brings back memories. I am a SWL, I had a DX 394 20 years ago until the grandkids mullered it by spilling water all over it. I had long wire made from old telephone cable. I made a simple antenna tuning unit out of a piece of broom stick wound with magnet wire which I copied from a radio book and it worked. One morning I received the South Island weather forecast from New Zealand to where I live near Dungeness. I was so surprised. I called all the people in the house to have a listen. I don't think Radio New Zealand broadcast on shortwave any more. I still love shortwave radio and listening all around. I received a QSL card from the Marianas Islands last year. They are north of Australia, so the bits of wire do work good sometimes. Thanks again for video again.
Rnz on air oks check their web for freq for europe
The 20 m wire is only half the antenna you need some ground radials in order to get anything reliably. If possible run a piece of coax all the way outside and then connect your wire as you've done but also connect several wires to the grounded part of the coax also known as the braid and you will improve your signal tremendously
How?
Can you link a plan?
Thanks for the great advice inbuilding your own Long Wire. I'm about to buy a screened copper wire (30Mts) and drape it all around the back garden, eventually will be connected to a battered old Tecsun S2000. Will get back to you here with the results.
This is what is needed. Even a layman can learn watching your Video. Great job and appreciate your effort.
john washington cheers
❤ Absolutely!
Be sure to ground your receiver. It is a very important part of the antenna.
...also a balun to get the right impedance.
Thanks for presenting your version of a quick and dirty, random wire antenna, you might enjoy greater sensitivity using the Hi-Z input on the DX394 (RCA on rear panel) instead of the Lo-Z (50 Ohm PL259 socket) input 👍
Additionally looping the connecting wires around each other then back on themselves (twisted) would vastly improve the mechanical strength of the join, naturally solder and heatshrink would provide improved weather resistance whilst also further adding to joint strength and added aesthetics 😊
ill give it a try. Solder a RCA connection to the wire then place it in the hi-z socket ? ive never used that socket on the radio. Maybe anther video coming up cheers
@@2j4ez No worries... a little envious of your local noise floor 👍
@@SpectreOZ I get loads of it my way go up the garden and it goes it seems to be only on HF
The DX394 owner's manual suggests attaching a long wire antenna to the "ANT HI-Z" plug on the back - you should that give you better reception that the SO239 input you used here - that's the "LO-Z" input, and it expects something like a dipole antenna instead.
I’ll have to give it a try
You should solder the connections and use heat shrink tube.
Hi , great video, I have dx394, can can configure to tune below LW , I do recommend a aerial tuning unit . Regards 73 de mark G8RDE
Tell ya what Im gonna try when my rcvr finally arrives. I have a 100' extension cord on a spool. (I roll it out to mow the lawn and wind it back up when Im done) so why buy any wire.
I can use an alligator clip to grab any one of the three wires on the plug and the braid I will also connect by alligator clip to a gnd wire from my out door faucet. If needed or desired I can "plug in" another extension cord to the end of the first one, and string em both along the top of my split rail fence. If needed (experiment) loading coils can be wound and alligator clips again used to connect. Since the wire is well insulated I could toss the end over the rioof to get the ant up in the air higher.
BTW Alternatives Ive seen: (An article where) a "slinky toy" was used for a long wire.
For a loop antenna, a roll of 25 wire ribbon cable stretched around a 55 gal plastic barrel with the ends connected together ONE WIRE OFFSET so s to create a 25 turn coil approx 30" dia.
A dipole of two tape measures back to back pulled to what ever length you desire.
I guess just let your mind wander and think outside the box. Lotta ways to skin a cat.
Awesome antenna quickie works fabulous on the DX 394 I love mine I think they are really underrated radios thanks for the idea I made one of your brilliant antennas but just used small electrical wire nuts to make connections. Thanks
For a radio with a SO239 connector you can use a banana jack on the end of the wire and insert it directly into the center of the SO230.
i could of used that but only had a piece of old coax with a pl259 plug lying around the shack
it is surely working, I don't know if the receiver have a 50 ohm input impedence, I just guess it would be better to tune the long wire with a hf balun/autotransformer, with a 9:1 ratio, or more.
It would good to make a 2nd part sequel
Huge thnx from Romania. Great vid. Just what I was looking for. Huge thnx
Very simple but effective temporary antenna. I enjoy doing experiments like thisand in the field with a portable. It is always surprising for sure. Thank you for sharing.
Thanks! This is helping me get started
It would be helpful if the hands were in the frame when performing tasks. Thank you for the simple wire design/explanation
I will be building one of these next week. I want to get on the 40 meter band.
The ground is still frozen so I will have to wait before putting the base for my vertical multi band antenna in.
Brilliant do I need to earth this aerial? Where I am all plugs are 2 pin with no earth.my receiver therefore has no earth. Thnx
STEVE HORNSHAW shouldn’t need to as your only receiving . If your receiver has a ground socket you can ground it by using a piece of wire from the gnd socket to the mud in your garden tied round a screw driver . But if your on the second or third floor it may act as a antenna you could also place it on copper pipe to ground it if need be
Thnx so so much and for your immediate rely, so much appreciated. Stay Safe. Steve in Romania
Simple and great usefull guide! Thanks, 73. PD. I have these receiver too.
Works great! Thank you very much!
Would it not be better if you looped it, came back into window and tied into the ground wires shielding the coaxial cable?
Great video. I have a shortwave radio that has a 3.5mm input jack. I have made a long wire antenna that uses an alligator clip to the whip antenna, but how can I attach a long single wire to a 3.5mm jack that I could plug into the 3.5mm antenna input?
I have another short wave receiver that’s got a 3.5mm jack socket for the antenna I’ve done a video on it check out my channel it’s a few videos back
Is it better to have an analog are digital receiver
I prefer analog if the Signal is very strong you can still hear it. On the digital radio if the signal isn’t very strong it just breaks up and crackles
Didn't know about the ten megahertz LSB divide
I like the "insulting tape". Just lose the "I done" instance and everything will be lovely.
I'm jealous that you have a garden
Thanks from California.
Does it make any difference if you ground the other terminal?
the receiver has a GND socket on it you could ground it.ill try and ground the other terminal and see what happens
When you splice your ways together try using a Western Union holds better...
Good, but how can you neutralize all the static electricity that the wire catches, before it goes into the receiver? I once did a simple antenna like this and on the connector I had powerful sparks..
Did you ground the ant.?
@@pauldavis22 I didn't, I am looking for a good way to ground it
You need to use a receiver atu to get max incoming signal a long wire will not be resonant over the bands your covering. 73
Can I lay the wure on a metal roof?
Dont see why not as your receiving not transmitting. but you may find you get a lot more interference from the metal roof. the only way to see if you get interference is give it a try
@@2j4ez Thank you.
What did you tie it to in your garden
👍 Tks from Bahrain.
I have the same antenna!
good vid and good use of random wire for your long wire antenna, how well does the "inverted V" antenna do with this receiver or is that more of a use-by-use case type setup?
Fox Nakamori hi I’ve never used a inverted v antenna on this receiver .
Can I use steel wire
dont see why not give it a try
@@2j4ez cheers pal
@@2j4ez steel wire worked! But I've bought some speaker wire 10m to give it a go with
Good Day. I found this video while trying to find one for an antenna. I have a Radio Shack Pro-97 Triple Trunking 1000 CH Scanner, 20-527, Fire Police Air Ham. I would like to know if this would work for my scanner? Please let me know. Thanks.
This simple antenna will only work on hf bands ie short wave the higher the frequency the smaller the antenna the lower the frequency the bigger the antenna
@@2j4ez Ok. Thank you for the reply.
How long does wire have to be ?,i want to listen to 0-35 mgz i have a 90ft washing line will that do or should i cut some off ?
If it’s got wire in the middle then you should be good go as your only receiving no transmitting and 90ft should be fine
Very fine !! I have a question about the wire.. Does the diameter of the wire can be important for a better reception ?
No. 73 de Peter DL8PJ
@@sevensugarqueen3148 Thanks a lot...
If your tight for room could you toss the wire into a tall tree?
Yep that would work as well
No trees on my property to speak of close by.. Will between two buildings do?
James Simms you could try it . It’s all about experimentation. It could be over a building
Great video Jez enjoyed it very helpful keep up the good work mate
Cheers I'm looking into building a tape measure antenna soon.
Somebody please please buy this guy a Soldering Iron....
Got one ill use it next time i do another video in making a antenna
And some heatshrink tube
@@MERCEDES-AND-DINO it was a quick antenna build if i make it again ill will add some heat shrink
You guys are always so complicated;
FINALLY A DETAILED HOW TO VID! ❤
Good show. Cheers. 73
Is there a Min Max to recieve on all Freqs?
100feet
@@thebasementstation4622 no broadcast Freqs Ham radio HF freqs ?
Perfect
Very good
I use a roach clip to attach to wire on my coax.
Roach clip LMFAO, I call them the same thing.
Never heard of solder in the UK , that receiver sound rubbish...... get ya self a nice SDR
Right on. Multi-tapped coil and balun with earth tap. My crystal set worked better that Radio Shack 394.
Newbie here. I could not understand anything on your receiver.
Great jod I hung my long wire bergen two trees
AGAIN, you failed to show the difference in reception having the long wire antenna on and off. So how does your demonstration prove anything????
Not a long wire... A random wire! A long wire is a different beast.
Dx am 3000 ,1750
Number stations?
@@2j4ez free radioamators from Rassia
👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
Just noise!!!!!
Pitiful simplistic video.
Very fine !! I have a question about the wire.. Does the diameter of the wire can be important for a better reception ?
No
@@mugsy5672 thanks a lot...
Very fine !! I have a question about the wire.. Does the diameter of the wire can be important for a better reception ?
@Timothy Miller thanks a lot...
@matt french Thanks a lot :)
Very fine !! I have a question about the wire.. Does the diameter of the wire can be important for a better reception ?
No, it makes absolutely no difference.
Yes, it changes reception quality, but you have no chance of noticing it without costy proffesional equiptment like we have in my Radioclub.
For this purpose like in video it's not important at all and you should worry about it.