✅

[@LuZoey]

very helpful, thanks!

[@asadusman-e4o]

can we draw surface lines along domain length to plot variables along certain positions instead of point in transient simulations?

[@sanjaykumavat8960]

How can I get graph for flow time vs wave hight at a particular line in a 2D numerical wave tank where wave generate from one side I mean from inlet pls reply it's for my project

[@SomaSekharGoudSontisomasekhar]

Can show flow time option in CFD post. Flow behaviour Animation with change in flow time.

[@dominicbruce7558]

Did you solve it?

[@nielgertenbach2360]

How can I measure the flow depth in an open channel cfd simulation?

[@taufiqjoe9402]

Hye Sir, so this is use to determine the ideal flow time in actual situation right? In transient, if the flow at the graph is in steady state that means that the timestep & number of time steps is sufficient to get accurate result. Correct me if im wrong. 🙏

[@rahul_bengali]

Bro when we have to do inflation in meshing?

[@redhotminipepper1]

inflation if important when you want to capture the near-wall behavior of a fluid. If you want to know the force by the fluid on a wall or accurately model convective heat transfer for example.

[@ansys_cfd]

it's right.
Thank you

[@blackrod_3456]

Does anybody know how to export the wall clock time or set it as a output parameter? - Thanks
I'm doing an optimisation and want to see what impact changes in the mesh have to the calculation time

[@simonevanlooveren5465]

Hi, I followed your video but i get an Error: floating point exception. Any idea what i did wrong?

[@ahmadyusuf2966]

Hi, how to write to file of the data plotted?

[@anujtyagi4380]

hello..how to find time average drag coefficient for transient problm in ansys fluent ??

[@ansys_cfd]

Here a tutorial about lift and drag coefficents:
ruclips.net/video/V_ozqKflSx8/видео.html
Regards

[@张宏伟-n5u]

sir,do you know why my report definitions has nothing?

[@johnbohn3626]

I am not getting this graph. Means it is not showing in screen. The original fig. And final fig. Are same..

[@the_anuragguha]

Sir, you have directly created the mesh... but sir before that you have to create the fluid domain inside the cylinder using fill command... so sir why you have not done that?

[@ansys_cfd]

Hi friend,
In this tutorial the geometry was created in DesignModeler. Please watch again the video.
Regards

[@amitshrivastava3335]

Can you show how to do energy balance of a 2D steel block by insulating it from 3 sides and giving heat flux at the bottom. Please show energy balance for the same, either
energy getting in the domain = energy stored
Thanks in advance

[@watermenlon3617]

why is my parameters under iterations instead of time steps

[@animalscartoonzoo953]

السلام عليكم ممكن رقم حضرتك للتواصل حيث اننى باحث دكتوراة فى مجال تحلية المياه بالطاقة الشمسية ببرنامج انسيس فلوينت ومحتاج مساعدة ممكن

[@mahirmahmoud2750]

دكتورة القناة باللغة الإنجليزية فما راح يفهم الكلام و لو تبحثين عن متخصصين عرب افضل واذا لغتك الانجليزي قوية ممكن التواصل معاهم

[@animalscartoonzoo953]

i need your help in my research my phd thesis in water desalination by cfd using ansys fluent , you can help me ????

[@candicekaplan5257]

why does this music kind of slap lol