Great editing and nice RC. I don't power wash my ESC like that anymore. I did it once to one of my RC vehicles and the ESC never worked again, so I just blow the RC with air from my electric blower instead. I'll clean the bottom with water and and soap, but by hand with a sponge. Hehe.
Thank you very much! Not recommended it either, although I’ve been doing this countless times with all my rc cars, I haven’t experience any issues yet with my ESC also not all ESC is waterproof. I only do this cuz I put them on display and I can’t stand looking at my rc full of dirt and mud. 🙂
What servo did you install? Was it a direct replacement or did you have to do some shimming due to height differences? Trying to figure out how to get this thing to turn...
9imod servo. You have to use the servo horn that comes with it and there will be slight angle from the horn to the servo saver but really doesn’t matter you can also use shims.
@@Deej_RC try adjust the springs first. dont be afraid to bottom out a lil bit.. its maybe the reason the shock mount is breaking because of the stiffness of the shocks, not absorbing enough..although small jumps like that shouldnt be breaking anything...maybe lighter oil? The tires also make it bounce if the shocks too stiff...
@@Deej_RC haha yes true ! If you have time look up Yantrs Servos ... more expensive than the 9imod but really good ... i have a few vids up with a 55kg in my green xmaxx and a notorious with a 45kg ....
I will try next time but people get bored easily with longer vids. 😅 also theres already tons of video regarding installation of this. So I’ll leave it to them. 🙂✌️
Love this video man! In the future a voice over would definitely make the video more interesting, but I really enjoyed not thinking and just watching the kraton fly around. Also I was surprised to see you spray wd40 over the whole rc. Do you do that to keep the shine to it or does it fight against dirt somehow?
Thanks man!! 🙂 I hate my voice and accent man unfortunately. 😂 I do to make it shine and looks new. My cleaning process is spray with soap then water then wd40 then water again to remove excess wd40 then just blow dry. My tires are sealed with shoe goo and you have to make sure water didn’t get into the receiver.
Once you spray with wd40 even if you spray with water it won’t come off totally unless you spray with soap. So once dried out it doesn’t looks sticky only shiny. 🙂
@@Deej_RC yes, I get issues even without the pressure washing, water manages to make it to connectors, screws and bearings, so even after blowing air with a compressor, 2 or 3 days afterwards you can listen the bearings squeaking and the screws all rusty
@@DashzRightI haven’t have that issue though cuz I spray WD40 all parts of the car then using paint brush to make sure everything is coated. But I’m pretty sure if you don’t spray wd40 it will get rusted. I’ve been running this on the beach as well couple times now.
WOW! Can't believe you wash the car with water and spray it that way. BAD-it's not water proof and the electrical won't like it either. And-to spray it with wd40-seriously! Best way to clean the car-just spray simple green everywhere-not to soak it-then just spray it with compressed air and it's clean.
Yeah don’t try this. 😅 I do this to all my RC, only thing I check after is the receiver box. wd-40 is to keep it new and prevent from rusting and seizing of bearings and screws. ✌️
Probably expects a Max 6 or 8, the same ole "boring" setup EVERY other rc builder uses. 🙄 Actually refreshing to see you use what you have instead of just buying every upgrade that nobody can afford, much more relatable. 💯
@@out_of_focus_racing ok u broke 3rd world loser. You ar boring af too and so is this comment section and this channel. No one wants to see stock, underpowered electronics, they have already seen that millions of times.. I will never watch this channel and it's been removed from my suggestions, great advice wus
Wow, this thing is rugged! Awesome editing!
Thank you! 😅
I’m glad to see that I’m not the only one who loves to get a car dirty, but hates to leave it that way.
Awesome video, excellent edits. Sun earned!
I can’t stand watching it full of dirt after using it. 😅 thank you!!
Awesome install n bash
Diggin the clean up session too
Nice of you to share 😎👌🏿
Thanks brother!! 😀
Great editing and nice RC. I don't power wash my ESC like that anymore. I did it once to one of my RC vehicles and the ESC never worked again, so I just blow the RC with air from my electric blower instead. I'll clean the bottom with water and and soap, but by hand with a sponge. Hehe.
Thank you very much!
Not recommended it either, although I’ve been doing this countless times with all my rc cars, I haven’t experience any issues yet with my ESC also not all ESC is waterproof. I only do this cuz I put them on display and I can’t stand looking at my rc full of dirt and mud. 🙂
Wow very clean And Nice video !
Thank you! 🙂
The video was really well done and the Kraton is of course also great😁
Very much appreciated bro!! 🙂
I love the music
Thank you! Free to use from youtube music library. 🙂
Nice one Deej, finally got the Kronos out today for a 4s shakedown. Would be interesting to see how they compare as we have the same electronics...
That’s awesome!! Let’s do it!! 😀
What servo did you install? Was it a direct replacement or did you have to do some shimming due to height differences? Trying to figure out how to get this thing to turn...
9imod servo. You have to use the servo horn that comes with it and there will be slight angle from the horn to the servo saver but really doesn’t matter you can also use shims.
Nicely done my brother!!!
Seems abit bouncy even at that small jump at the track?
Thanks bro!! 😀it’s not as bad compare to my xmaxx might need much thicker shock oil?
@@Deej_RC try adjust the springs first. dont be afraid to bottom out a lil bit.. its maybe the reason the shock mount is breaking because of the stiffness of the shocks, not absorbing enough..although small jumps like that shouldnt be breaking anything...maybe lighter oil? The tires also make it bounce if the shocks too stiff...
@@KingsRC springs only adjusted to half I think it’s broken when doing the speed run and fell off on the race track.
Wicked video , enjoyed every bit of that ... i use those 9imods in my Xmaxx and they havent let me down ...
thanks heaps mate! I use it in my Xmaxx too so far so good! 😀 I did the jx46kg but fails after couple runs.
@@Deej_RC i never tried the jx46 before .... but yea the 9imod been using in my red Xmaxx for over 8 months and still goes hard on 7.4 bec too
@@kaosr.c I was thinking about getting the Savox but hey that’s equivalent of 4 or maybe 5 of these cheap servo that is working well. 😂
@@Deej_RC haha yes true ! If you have time look up Yantrs Servos ... more expensive than the 9imod but really good ... i have a few vids up with a 55kg in my green xmaxx and a notorious with a 45kg ....
@@kaosr.c I’ll check that out. Thanks mate!! 🙂
Nice video. Liked and subscribed 🙏. I also post rc vids and its so much fun. Reminds me of my good old days.💪
Awesome! Thanks man!! 🙂👍
Good video but would be nice if you explain things. Some people are new at this and would like to know what is going on
I will try next time but people get bored easily with longer vids. 😅 also theres already tons of video regarding installation of this. So I’ll leave it to them. 🙂✌️
But if you have questions regarding the build I am happy to answer it. 🙂
Love this video man! In the future a voice over would definitely make the video more interesting, but I really enjoyed not thinking and just watching the kraton fly around. Also I was surprised to see you spray wd40 over the whole rc. Do you do that to keep the shine to it or does it fight against dirt somehow?
Thanks man!! 🙂 I hate my voice and accent man unfortunately. 😂 I do to make it shine and looks new. My cleaning process is spray with soap then water then wd40 then water again to remove excess wd40 then just blow dry. My tires are sealed with shoe goo and you have to make sure water didn’t get into the receiver.
Once you spray with wd40 even if you spray with water it won’t come off totally unless you spray with soap. So once dried out it doesn’t looks sticky only shiny. 🙂
that pressure washing really made me cringe
😅 Do you have bad experience when using pressure washer?
@@Deej_RC yes, I get issues even without the pressure washing, water manages to make it to connectors, screws and bearings, so even after blowing air with a compressor, 2 or 3 days afterwards you can listen the bearings squeaking and the screws all rusty
@@DashzRightI haven’t have that issue though cuz I spray WD40 all parts of the car then using paint brush to make sure everything is coated. But I’m pretty sure if you don’t spray wd40 it will get rusted. I’ve been running this on the beach as well couple times now.
@@Deej_RCdoesn’t that collect a ton of dust? I guess it doesn’t matter if you pressure wash it lol.
@@rybobuno you have to spray with water again to remove the excess.
Don't power spray your rc's!
👍
WOW! Can't believe you wash the car with water and spray it that way. BAD-it's not water proof and the electrical won't like it either. And-to spray it with wd40-seriously! Best way to clean the car-just spray simple green everywhere-not to soak it-then just spray it with compressed air and it's clean.
Yeah don’t try this. 😅 I do this to all my RC, only thing I check after is the receiver box. wd-40 is to keep it new and prevent from rusting and seizing of bearings and screws. ✌️
Lame. Why get and exb and put stock electronics in it. BOooring
That’s all I can afford at the moment man.
What electronics that are not boring to you? 🙂
Probably expects a Max 6 or 8, the same ole "boring" setup EVERY other rc builder uses. 🙄 Actually refreshing to see you use what you have instead of just buying every upgrade that nobody can afford, much more relatable. 💯
@@kyongkim702 agree! Although I have max6 and if I put that on my Kraton 6s drivetrain I’m gonna need more money for spare diffs. 😂
Bro shut up and leave him alone. It’s called saving money and being financially responsible. If you don’t like it, don’t watch his videos
@@out_of_focus_racing ok u broke 3rd world loser. You ar boring af too and so is this comment section and this channel. No one wants to see stock, underpowered electronics, they have already seen that millions of times.. I will never watch this channel and it's been removed from my suggestions, great advice wus