How secure is this? If you are using the onboard relay of the reader. If you rip it off the wall your door will unlock, because it's a fail safe lock. If you want security you should use the wiegand output and program it with a computer.
If this is a video anyone here is learning on.. make sure you cut your jackets all the same length... all in a 90 degree fashion.... Most of all your conductors need to be terminated so that they are not visable under the terminals.. he almost shorted a million times... treat the wire as it is hot at all times, you will not regret these tips. sounds arrogant, but I am one of the best at the craft. This stuff is not difficult to install, so you want to make sure when you leave the product on a customers property it looks like they couldn't do it themselves. They will be looking at it for the rest of the time they have it! If you are a novice I recommend you spin the cables with the jackets cut all the way back and secured together. Lable the jackets out of sight. get a lable maker and mark them at each terminal on the board. Good Luck!
Good analysis. However, even though it's for demonstration purpose but the termination of the cable should be properly done as I noticed some bare conductors showing.
Where can I found this metal panel control with the powersupply.. with switch on off ... all powersupply panel that i found are with a suspicious power supply with no switch
we are using only door lock and door contact but i terminate lock cable this one from door to control board .what is my qus directly connect to board nc and c or using relay
Sorry fella but your termination technique is rubbish. The stripped wire strands should be twisted tightly together, then bent back on themselves to give more contact area before inserting into the terminal. Also when terminating, you shouldn't have all that bare conductor showing outside the terminal.
Your video is horrible. You're not explaining anything. I was trying hard to follow you. I kept stopping and rewinding it, yet I still got nothing out of it. You kept talking in some language, no clue what you're talking about.
No worries just put the captions in English in the settings and thank me later.
How secure is this? If you are using the onboard relay of the reader. If you rip it off the wall your door will unlock, because it's a fail safe lock. If you want security you should use the wiegand output and program it with a computer.
That's right and it must always be on the secured side of the structure.
If this is a video anyone here is learning on.. make sure you cut your jackets all the same length... all in a 90 degree fashion.... Most of all your conductors need to be terminated so that they are not visable under the terminals.. he almost shorted a million times... treat the wire as it is hot at all times, you will not regret these tips. sounds arrogant, but I am one of the best at the craft. This stuff is not difficult to install, so you want to make sure when you leave the product on a customers property it looks like they couldn't do it themselves. They will be looking at it for the rest of the time they have it! If you are a novice I recommend you spin the cables with the jackets cut all the way back and secured together. Lable the jackets out of sight. get a lable maker and mark them at each terminal on the board. Good Luck!
It definitely does make it look better to make the metal hidden, also nice cable routing is very nice.
K
Is there a code we need to set on the keypad for it to work or it is installed as it is
Good analysis. However, even though it's for demonstration purpose but the termination of the cable should be properly done as I noticed some bare conductors showing.
what is the best way to connect biometrical reader to a turnter with a push button?
2 door not working. Red led blinking. Any problem
If you don't have electricity (cut from company some hours) how does work all the system?? To opened the door?? :-)
Use With Batter Source 12v 2x Amp 7 :-)
I mean Battery Source
Can you turn the timer off? push a button and it stay lock / unlock until you push again.
i need the power supply unit can u give us a link
i have one doubt ,Battery,load o/p,em lock, up this all k aft that ( input) wires where its goes to connect??????
Where can I found this metal panel control with the powersupply.. with switch on off ... all powersupply panel that i found are with a suspicious power supply with no switch
Hi art
how to termination only lock and door contact to the board .we need relay connection or direct connection
we are using only door lock and door contact but i terminate lock cable this one from door to control board .what is my qus directly connect to board nc and c or using relay
when did soldering get replaced by a philips head? sweet
PLZ SUBCRIBE MY CHANNEL IF YOU NEED KNOW ABOUT FIRE ALARM SYSTEM
i have access control system its not working and programing card is not working how you can help me
Bisa atau tidak reader di combined dengan finger? jadi untuk masuknya menggunakan reader dan keluarnya memakai finger?
what type cable do you using for EM lock?
I could have been the best video if you continued only in English
Asanthi Udawatta yes
seriously wtf is up with that! i was starting to understand then he just changes languages.
PLZ SUBCRIBE MY CHANNEL IF YOU NEED KNOW ABOUT FIRE ALARM SYSTEM
can I have the multi door access control for apartments
I wnat to card access. all system. breck glos. em lock. push baton. reader.all
How can get full video
show the archeticture of access control
Qual é a placa que você usa??
Try to use 125Khz(TK4100) cards or Mifare(13.56Mhz) cards. :)
Thank you ;)
Welcome. :)
your, not explaining anything....and you keep changing language!!
boss english only please... usefull video but hard to complete understand.
VERY USEFUL VIDEO.
why u started talking in different language in between?
Roses are red
Violets are blue
The title's in English,
Then why aren't YOU?
Klu door tu xlekat pe msalah nya.
Stu lg card access xbole nk touch mksd nya xbole digunakn lg.
Magnet kena pasang sesuai . Atau tamper masih sot , kena periksa Satu persatu..
English convention I prefer it
very nice
Hi get more details
Ini barang senang faham..
ih hose a mess
Useful
nice vedio
Sorry fella but your termination technique is rubbish. The stripped wire strands should be twisted tightly together, then bent back on themselves to give more contact area before inserting into the terminal. Also when terminating, you shouldn't have all that bare conductor showing outside the terminal.
too much movements making it boring.
very nic
singapore layou
woow good
Your video is horrible. You're not explaining anything. I was trying hard to follow you. I kept stopping and rewinding it, yet I still got nothing out of it.
You kept talking in some language, no clue what you're talking about.
power ne
💣 💣
Ww