🟠 Now that you have your devices wired to your Access Control Panel, we recommend you to watch "How to program and configure Visionis VSAxess Version 3.2.0.52" so you can connect your panel to a management software. Here is the video 👉ruclips.net/video/xUhvzubCcZU/видео.html
Same question on the yellow wire. The previous version of the video showed changing a setting from Cathode to Anode but the current software doesn't seem to have that setting.
Hello Will, Please Open VSAXESS software and go to: Access Control > Advanced Function > Device parameters > click on your panel > click on the door > Entrance card reader 1 > Advanced > change all three polarities from anode to cathode and then copy to all the readers. This videos is only about the wiring process but we are working in the video with the programming in the VSAXESS sofware using the new updated version of it. We'll let you know when that video is published. Thank you for your comment.
Thanks for the updated video. If, for some reason, you forget to remove the yellow wire prior to powering on system and the "forever tone" activates, How do you remove or silence it?
Hi Damion, You will disable the long beep by opening the VSAXESS software and going to Access Control > Advanced Function > Device parameters > click on your panel > click on the door > Entrance card reader 1 > Advanced > change all three polarities from anode to cathode and then copy to all the readers. This videos is only about the wiring process but we are working in the video with the programming in the VSAXESS sofware using the new updated version of it. We'll let you know when that video is published. Thank you for your comment.
Hi North Blue. We will be putting up a video on that soon. For now you may call our tech support department to assist you with the wiring. 1-888-504-3318
I would appreciate if you do video for model VS-AXESS-4DLX with VIS-3002 Wiegand Card Reader, have lot of difference with this model & the one which i had 4DLX model..
I noticed there was no actual demo but do I assume the OK terminal on the controller is for the reader's LED and the Beep is for the beeper. Are these assumptions correct and you need to run an actual demo with a card and lock connected.
You should probably learn how to put your own panel together before going to RUclips. Those terminal blocks disconnect so that you can do wiring much easier, as opposed to the dyslexic version we are forced to watch. Good luck🤮
🟠 Now that you have your devices wired to your Access Control Panel, we recommend you to watch "How to program and configure Visionis VSAxess Version 3.2.0.52" so you can connect your panel to a management software. Here is the video 👉ruclips.net/video/xUhvzubCcZU/видео.html
Same question on the yellow wire. The previous version of the video showed changing a setting from Cathode to Anode but the current software doesn't seem to have that setting.
Hello Will,
Please Open VSAXESS software and go to: Access Control > Advanced Function > Device parameters > click on your panel > click on the door > Entrance card reader 1 > Advanced > change all three polarities from anode to cathode and then copy to all the readers.
This videos is only about the wiring process but we are working in the video with the programming in the VSAXESS sofware using the new updated version of it. We'll let you know when that video is published. Thank you for your comment.
Thanks for the updated video.
If, for some reason, you forget to remove the yellow wire prior to powering on system and the "forever tone" activates, How do you remove or silence it?
Hi Damion,
You will disable the long beep by opening the VSAXESS software and going to Access Control > Advanced Function > Device parameters > click on your panel > click on the door > Entrance card reader 1 > Advanced > change all three polarities from anode to cathode and then copy to all the readers.
This videos is only about the wiring process but we are working in the video with the programming in the VSAXESS sofware using the new updated version of it. We'll let you know when that video is published. Thank you for your comment.
@@FPCSecurity thanks for your detailed response. I appreciate that. Will be purchasing one of these units for my lab soon
Purchased the VS-AXESS-4DLX 4 door with bus system. Can we have a video on wiring for that one please? thanks.
Hi North Blue. We will be putting up a video on that soon. For now you may call our tech support department to assist you with the wiring.
1-888-504-3318
I would appreciate if you do video for model VS-AXESS-4DLX with VIS-3002 Wiegand Card Reader, have lot of difference with this model & the one which i had 4DLX model..
Hi Jagadish, thank you for the suggestion. We will keep this in mind to create this type of video in the near future.
I noticed there was no actual demo but do I assume the OK terminal on the controller is for the reader's LED and the Beep is for the beeper. Are these assumptions correct and you need to run an actual demo with a card and lock connected.
Hi Gerald. Yes, your assumptions are correct.
the mag lock didn't come on
Ahmed to help you please contact us at 1-888-504-3318 or support@fpc-security.com . thank you
Would it have killed you to get the real Jimmy Smits? This knockoff is engaging but distracting.
You should probably learn how to put your own panel together before going to RUclips.
Those terminal blocks disconnect so that you can do wiring much easier, as opposed to the dyslexic version we are forced to watch.
Good luck🤮
Dear marxg4, thank you for your comment. On our next video we will make sure to follow your advise about the terminal blocks.