EASY & SPECIAL 4WS SETUP | EDGETX | MT12 [EN]

#radiomaster #mt12 #tutorial In this video we are going to make a special 4WS steering setup.
The setup should provide the following functions:
- Control over the steering modes with Switch A (SA)
- If SA is in outward position: front wheel steering only
- If SA is in middle position: 4WS steering
- If SA is in inward position: Crab mode
But: if SA is in outward position (front wheel steering) then the steering on the rear axle should be controlled with the pot P1 independently from the front wheel steering.
If you like my work, please hit the like and subscribe buttons and feel free to buy me a coffee:
www.buymeacoff...

[@ProRCCrawler]

Great video. Works perfectly. Thank you for taking the time to do this 💪

[@DanPRC]

Awesome video! I have several micros with AWS and now I can bind them to my 4in1 if I please! Specially my AWS 6x6. I’m glad you decided to keep making these help videos and accept challenges! I just bought you a cup of coffee. Lol

[@arminrc]

This is cool and thank you very much for your support (coffee)! It is highly appreciated! May I ask, what Rx you are using in your micros?

[@DanPRC]

@@arminrc You’re welcome. And I use Dumbo Rc receivers.

[@envious4504]

This is absolutely awesome! Thank you so much for the help and your knowledge. I have one question. I have a printed file that makes it easier to actuate S2 as well as places a gate on it (which I used in place of S1 for the manual control of the rear wheels) and I am trying to figure out how to adjust the S2 knob to give me full steering with the physical gate installed. If you have any insights or if you have covered this in any of your other MT12 videos please let me know.

[@arminrc]

Thanks for the comment! I guess it depends whether you use the full throw of the pot (means, you wanna hit the endpoints) or not. If you wanna hit the endpoints when using S2 for rear steering (or any other function you may see fit) then, well, there is not much to do about it!. But if it is not necessary to use the full throw of the pot, then please take a look at the Weight setting (you can go beyond 100!) or - better - check out custom curves.

[@AllevRot]

Your videos are some of the best I found from the limited number available. Yours are also the most straight to the point and easiest to follow I believe,. For mine I have programmed it similar: My rear steering servo is on Rx Channel 4 & independently controlled RearWS from pot P2. I also use switch SA inner position for FrontWS, middle position for 4WS and outer position for Crab Steer. It is a matter of preferences really. I just think that I find it more intuitive set up this way. Thankyou, keep them coming.

[@arminrc]

Thanks for these inspiring words! Highly appreciated and I am glad that my videos are of some help for you! The really great thing about EdgeTX is, that there is not only one way to get a specific result. Everyone can set it up exactly the way they want it. I know that this fact may seem overwhelming to some in the beginning but once you master it, it gives you amazing flexibility and it seems you have mastered it! 👍

[@jleftbrane]

Thanks so much! All the other
"solutions" I've seen are overly complicated and would be hard to use during a comp. !
I had a feeling it was easier !
You made this sooooooo easy
Please change the title to " easy 4WS on MT12 😂
A coffee is coming your way!!!❤

[@arminrc]

Thank you for the comment! Its good to see that this is what you need! Changed the title 😀

[@ProRCCrawler]

I'm looking to add one more function to my rear steer. I would like to select the T4 trim switch. When I press is up I want to add 10 points to the rear steer in one direction, and if I press it down, add 10 points in the opposite direction.. Any tips?

[@arminrc]

You could try to alter a global variable with the T4 switch through a special function. Then this global variable could be used in the mixes on the offset. I did not test this but this could work.

[@JPWirt]

This is great! Thank you for posting!

[@arminrc]

You are welcome! Glad you like it!

[@jaredphipps3757]

Top notch videos as always!

[@arminrc]

Thanks Dude!

[@Skråningsulv]

thanks for the good turtorials.

[@arminrc]

Thanks Dude! The thumb steer adapter I designed/printed myself. You can find it on thingiverse (arminrc)

[@AgilityDogAlvar]

Vielen Dank für die einfache Erklärung. Sehr passend für mich da ich gerade einen 3Achser mit zwei gelenkten Achsen baue

[@arminrc]

Dann kam das Video genau zur richtigen Zeit 😉 Vielen Dank für den Kommentar!