Yesterday I stumbled on this video. I have the Barkbusters VPS Handguards on my Husaberg FS 570 Thanks to the video I'm the protector on the throttle now get properly fixed Greetings from Germany
I've been of the firm opinion that hand-guards (barkbusters) are stupid. That was until yesterday. Navigating a narrow and heavily overgrown trail a large piece of some plant went and applied my breaks for me. This caused me to grab the throttle and then do an accidental wheelie. My bark-busters are coming today.
@hondarider9494 Dependant on what type of bars you have they may have a little plastic plug in the end which will just pop out, otherwise just drill or remove that piece so you have metal sowing on the inside of the handle bar. You should not be cutting into the throttle!
@hondarider9494 Standing at the side the bike looking at the grip, grab a utility knife and just cut the inside bit of rubber out of the grip. So now you will still have the thicker edging of the grip remaining as you have just cut the inner piece out to fit the plug and bolt for your barkbusters.
Depending on the model bike you have. The specific kit you buy for your make and model will be designed to go into the handle bar end and accommodate a handlebar weight if needed.There are Barkbuster handguards that don't require to be connected to the bar end,
@hyk000 How do u install acerbis rally II handguards? Do u know? If so do u have to cut the end of the grip and drill the inside of the throttle handle like in chaparral motorsports video?
the "non hacksaw" gaurds are Just for guarding brush and flying dirt and rocks. they are not as strong. they a just made of plastic and will not protect against hitting a branch or something, or falling down.
If you think this is complicated please take a basic mechanics course before you start riding at all. for your own safty! there is no way you will be able to perform adequate basic pre riding checks on your bike. or even fix it in an offroad condition.
Bo B. Jacobsen taking the throttle off is what is putting people off. I wouldn't recommend Messing with the throttle if your incompetent with mechanics, for the small fee a shop will charge to fit it it's not worth it
@hondarider9494 Get the ones that arent wrap arounds. Go to my channel and Check out my xr350r walk around video. I have some made by Tusk. Alot of other companies make that style to.
Yesterday I stumbled on this video. I have the Barkbusters VPS Handguards on my Husaberg FS 570
Thanks to the video I'm the protector on the throttle now get properly fixed
Greetings from Germany
Thank you (even though I fitted Acerbis Rally Pros) really simple and easy to follow.
My bar end insert kit fits inside the bar with zero resistance.. Shouldnt it be a bit of a tight fit?
I've been of the firm opinion that hand-guards (barkbusters) are stupid. That was until yesterday. Navigating a narrow and heavily overgrown trail a large piece of some plant went and applied my breaks for me. This caused me to grab the throttle and then do an accidental wheelie. My bark-busters are coming today.
@hondarider9494 Dependant on what type of bars you have they may have a little plastic plug in the end which will just pop out, otherwise just drill or remove that piece so you have metal sowing on the inside of the handle bar.
You should not be cutting into the throttle!
@hondarider9494 Standing at the side the bike looking at the grip, grab a utility knife and just cut the inside bit of rubber out of the grip. So now you will still have the thicker edging of the grip remaining as you have just cut the inner piece out to fit the plug and bolt for your barkbusters.
Is it necessary to use handle end bar to install this hand guard. Kindly suggest.
Depending on the model bike you have. The specific kit you buy for your make and model will be designed to go into the handle bar end and accommodate a handlebar weight if needed.There are Barkbuster handguards that don't require to be connected to the bar end,
@hyk000 How do u install acerbis rally II handguards? Do u know? If so do u have to cut the end of the grip and drill the inside of the throttle handle like in chaparral motorsports video?
@hyk000 they dont have aplastic plug. Ill just hafta get some guards that dont connect on the outside of the grips too
Yeah I've never had hand guards line up that easy.
where abouts can i buy these exact ones and how much are they
Very helpful,thanks
Would ego barkbusters fit on a klx140L?
Will it fit on a re Himalayan
I have a DR650 and I am going with the Jet version. Its going on a stock bars. Do I get tapered or straight?
Did you ever end up installing on your Dr. I am curious about this also. I believe straight.
Not working on my BMW 310 GS. Doesn’t fit
Thanks helpful video
the "non hacksaw" gaurds are Just for guarding brush and flying dirt and rocks. they are not as strong. they a just made of plastic and will not protect against hitting a branch or something, or falling down.
Add links for this product in description
If you think this is complicated please take a basic mechanics course before you start riding at all. for your own safty! there is no way you will be able to perform adequate basic pre riding checks on your bike. or even fix it in an offroad condition.
Bo B. Jacobsen taking the throttle off is what is putting people off. I wouldn't recommend Messing with the throttle if your incompetent with mechanics, for the small fee a shop will charge to fit it it's not worth it
Bo B. Jacobsen amen!
great Vid
If this guide seems difficult please hand in your man card at the nearest sports bar
how do u take them off to change grips?
Watch the video in reveres?
I dont want to cut my grips and screw up my plastic throttle under my grips! All I want is handguards without having to ruin my bike! HELP! SOMEONE!
you call that easy,he must be kidding
That doesn't look easy to me. I guess I need to take my bike to the dealer to have it installed
my job for tomorrow lol
@hondarider9494
Get the ones that arent wrap arounds. Go to my channel and Check out my xr350r walk around video. I have some made by Tusk. Alot of other companies make that style to.
the bolts on mine are stripped so I thought I was doing something wrong
ANYONE NO OF ANY OTHER BRAND WHERE YOU DON'T HAVE TO DEFORM YOUR BIKE TO GET THIS SHIT ON?
That guy just looks Aussie
Deh-Brie , or. Duh-Brie? 🤔
seriously?
H
LOL
Ooohhhh , cutting is required, HELL NO & NO SALE. !!! ( What language is this smuck speaking ? )