FN P90/PS90 30rd Magazine Into 50rd Conversion
HTML-код
- Опубликовано: 8 фев 2025
- This is what I did to convert a 30rd FNH PS90 magazine into a 50rd magazine.
DISCLAIMER: This video is only a showing of what I have accomplished with this product. Anyone who desires to reproduce what I have done does so at his/her own risk. Depending on the skill level of the person attempting to reproduce what I have done, the final results will vary. Poor workmanship will result in a poorly finished product and could also cause damage to the product and/or rifle or could cause harm to the person using the product and/or those around him/her. I do not have any control over the skill level of anyone attempting to reproduce this project and I therefore cannot be held responsible for carelessness and/or poor workmanship.
Thanks, i just converted 3-10 round magazine's to 49 round mags. It was very easy to do.
Hi, for those that might have a feed problem, make sure the plastic follow is the correct way in and not upside down - with regards the forwards & backwards slant of its face - the shorter length is on the mag bottom and the longer one is uppermost.
good deal, i have a califunny 10 and bottom plate seems attached. but after watching this, in the trash it goes buying a 50
Took me 15 minutes with a small hacksaw, and no vice. I’d suggest Midway for FN magazines on the cheap.
Woo I did it, except I glued the 2 pieces together so that the wire could clip in. Only lose 1 round anyway.
Laws that state a maximum capacity are inherently unconstitutional.
Great video my friend! Thank you!
Thank you, excellent video!
Wouldnt this reduce the reliability when firing? Since the tension for the magazine spring is much lighter than compare to when it's 30?
It appears to be the same spring as with the 50 round magazine. If you look at a 30 and a 50 side by side, they have the same number of coils with the 30 looking more compressed. That's not to say that sitting in the magazine effectively loaded with 20 rounds worth of tension hasn't worn the spring out a bit, but for the most part it should function just fine.
I can confirm that the spring in the 30 mag is the same as the 50. That’s why loading the 30 mag is harder than the 50.
I have an after market 50 rd mag and the spring in it is shorter than the 30 rd spring in the mag that came with the ps 90. By around 3inches shorter. Will be modifying mine too. I am in a state we’re it’s legal .
Jim, I'm loving your PS90 videos. Thank you for sharing these. I have to ask though, where is that accent from. Almost sounds slightly Scandinavian. :)
Thanks!
Well, I'm not from any specific place; I grew up going everywhere in the states since I was in a military family.
I've lived my formative years in just about every place; from the East Coast and the South until I was a toddler, then to the west coast in California until I was halfway through elementary, and the remainder of my childhood back in the central south again before graduating high school and enlisting into the military myself
As far as Scandinavian, I never thought that my overemphasis on enunciation would make me sound like that! LOL
Thanks. Cut or dremel. Nice
There is actually a 3d print for a proper spring plate. If you got an ender 3, put it to use
TY!!! Liked & subbed
great info, thanks
I have seen this done without any cutting. Keep looking and you will find the correct video.
Will this compromise your springs longevity?
You could probably 3D print a smaller piece instead of cutting the plastic if you have access to one
Can this be done to a ten rounder or are the springs different
10, 30, & 50 round magazines all have the same springs. I keep the little spring retainer and have all 49 rounders except one where I did a whole lot of sanding on both the floor plate and spring retainer to get 50. But I save like $12 online when I order the 10 of 50 and just cut the block.
Does it cause reliability issues when converting into a 50 round magazine?
No
No. It was designed for it.
isn't the spring too short afterwards? I can't imagine the exact same spring length used in the 30 mag vs the 50 mag, as the 30 mag tension would be super tight with all that extra tension
No
Thx dude, I'll test in in da hood
Why do they give you a 30 and sell 50's? Stupid question I suppose...
Important regulations.
You do know that there was no reason for you to remove all the pieces right? All you needed was the spacer and to just cut it. Just a friendly tip that could save you 20 minutes
Saved me thanks
Its also good to know the condition of your rollers, feed ramp, and how to put it all back together.
does it still feed correctly
This video should be less than 30 seconds... 😂😂😂
Why bother. Just buy another 50 or another 4 like I did.
Ig they are poor 🤷🏻♂️
It saves some money by doing the conversion. That money could get another box or 2 of ammo, but I'd probably keep my 30 rounder and get more mags too.
What’s the point of having a 30 rounder when you can have 50? Get more mags if you want but if you only want 30 rounds just put 30 in it rather than 50
@@thekingsmen4631 mine came with a 30. Didn’t want a 30 & 9 50’s so now I have 10 50’s. 🤷♀️
@@Emiator exxxxaaactly
Did too much but thank you anyways
😁👍🏽
Nice video Jim
Nice