How to install a Curb for standing seam metal roofs (Double LOK Panels)
HTML-код
- Опубликовано: 23 янв 2021
- 5/16" Locking Bits for use with stainless fastners: amzn.to/3cEa2TU
Roof curb for sale: amzn.to/2YXr8EK
Skylight curb : amzn.to/2MPUW3J
Get your Malco ER3 : amzn.to/2MFkzEt
Hemming tool: amzn.to/3tJAnGX
Midwest seamer: amzn.to/2N6jtBo
In this video we install a Curb by CurbsPlus. This curb will hold the roof mounted HVAC unit. We try our best to seal it to the roof with all measures necessary. This video is to show how we install it. I hope I am able to help those that need guidance in this procedure and you pros are welcome to leave a comment and let me know how I should have done it.
Whomever you may be, give us the thumbs up and hit the notification bell and
Please SUBSCRIBE!! 
Хобби
OSHA would have a field day on this job
Looks great
Hack job all the way
You don’t cut a curb in at the top, as the roof expands and contracts this will tear and cause leaks, proper installation is either over/over or under/under. 2.5” mastic gasket is the only way to water proof a commercial roof curb. Silicone will oxidized galvalume roof panels and void manufacture warranty. Roof curbs should be installed as roof is installed under/under for best results. Over/ over is for retrofit applications. 20 years experience certified PEMB roof installer.
Lucas, you have any videos for over/over install?
when you mark where to cut the deck .. we have a 8" roof because the foam insulation in between do i use a long metal bit to mark from underneat ? I really dont want to make mistakes
@@MrAllister9 yes
Fantastic video! Looks like a dollsr general store, or family dollar
Excelente trabajo podrás hacer video o tendras fotos de preparación por debajo de rooftop
Finally, someone showing how a roof curb goes on a standing seam roof.
Pass the silicone sealant over here. We gonna need it!
Standing Seam concealed fastening system gets a non concealed roof jack.?
Were Grinders not invented when this was produced? Secondly epic fail unless the curb is getting an adapter because i didnt see any sort of leveling
@1:02 why is there a man dancing around the open hole with a red hankerchief with no harness on him? he is going to trip and fall into the hole. If I saw this on one of my jobs, the job would stop until this is followed and understood. For the installation detail, I would have removed the standing seam roof panels, installed the curb, then put the roof back on. One summer with this roof heating up and cooling down, expanding and contracting, and it will leak at every seam here. (architect since 2004)
If i wanted a music video i'd go to tiktok
Where do you find the caps for a r panel I'm installing curves now and cannot seem to find any
Fabricator of the curb supplies the caps as to which roof panel is used.
What is the sealing tape you used?
It is a Butyl tape. Very good stuff.
HOW DID YOU INSTALL THE EQUIPMENT TO THE CURB?
Not my work ..HvAC guys did that part.
typical Iron works
You should’ve went further up roof to where screws are in beam. Take screws out , push curb up instead of fighting it🤙🏽… put back those screws 🙃 P.S. curb should go on top of both highs on each side
ps those screws are not in a beam they are holding a pan on the bottom panel and if you take them out said pan falls out
Do you have IG? I have a question for a pro and I will pay for the answer.
NARF.Buildz
The title should be how to frig up a metal roof JUST SCREW INTO THE FLAT PART OF THE SHEETING INSTEAD OF THE RIBS.
Where’s the fall protection ?
Fall? 🤔I learned to stand up right after I learned to crawl.😉
That's for wussies
@3:41 no harness in a scissor lift? Naughty, naughty.
Das Wasser fließt wohl anders in Amerika, als in Deutschland.
i wanted to see how you guys marked the rtu hole from underneath ... but you skipped it all .. im doing a roof with q deck and gravel on top and its 8" cause the foam in between ... i would just use a long bit from underneath and drill though kinda thing?
We had the hole framed and when we installed the roof we marked location of the hole at that time.
Si trabajaran para las compañias que yo les hago metal en el primer trabajo estan despedidos eso no va asi ese trabajo wsta muy mal
Cada compañía tiene diferentes estándares.
I think I will leave the metal intact and forget the skylight
Great choice.... Skylights usually leak within 5-10 yrs.
Execução do trabalho horrível, parece não saber fazer a instalação. Duvido não ter vazamento