Amazing skills for the reflow. Did the digitizer replacement but still facing the same fault. Do not feel comfortable with the CPU reflow. Is it possible to reflow the CPU with flux without removing the underfill ? Can you confirm if the boosted 15 volt will be absent if the digitizer is not detected by the CPU? Ours is missing. Garbage PCBA by the contractor.
Obviously not recommended to reflow the CPU, it could work for couple of hours/days/weeks but not long for sure, can you be more specific about the boosted 15v line ??
@@AntoineKiriaky10 Thank you so much for the reply. The referenced 15v boost is the PP15V0_TOUCH. It is at 0 volts and may be due to the A10 CPU losing the bonds under the BGA. With regret, believe the A10 is no longer due to the reflow attempt. Can you comment on if the a10 CPU on Aliexpress for the iphone series are the same or not for the ipads? Also, there is a mention of the A10 RAM. Is this a dual layered CPU package? Welcome your comments. We have a reflow BGA workstation that will be deployed on the next attempt (Seamark). Need guidance on the A10 CPU replacement. Does the serial # change once the CPU is replaced? Which tool allows for the proper activation of the logic board after the replacement? The logic board is unlocked but the touch was not working. We replaced the digitizer with a new one - no go. Replaced the Broadcom touch IC - reflowed fine but still not working. The SPI CLK line in diode mode was fine. With regret, did not check the other SPI lines in diode mode after the balls were cleaned on the PCBA. Thanks again.
Hey actually my ipad screen also stopped working, i asked some local service centres and they said ipad screen is dead, but it should first start to get slow or something, because it literally just stopped responding to touch while i was using it, like literally in a snap, a second. So can it be a hardware issue or a software one, plz reply And yes the ipad is working perfectly fine, no slow no heat just the touch, home button is also working like new, my ipad is 6th gen 2018 ver.
Amazing work happy to see u in RUclips today seen your RUclips channel happy happy
Excellent video but where can I get a copy of schematic for all iPad ? Thank you
Good jobman!
Only one poor line can destroy everything ;)
Чому тут так мало підписок? Цеж топ канал!
Amazing skills for the reflow. Did the digitizer replacement but still facing the same fault. Do not feel comfortable with the CPU reflow. Is it possible to reflow the CPU with flux without removing the underfill ? Can you confirm if the boosted 15 volt will be absent if the digitizer is not detected by the CPU? Ours is missing. Garbage PCBA by the contractor.
Obviously not recommended to reflow the CPU, it could work for couple of hours/days/weeks but not long for sure, can you be more specific about the boosted 15v line ??
@@AntoineKiriaky10 Thank you so much for the reply. The referenced 15v boost is the PP15V0_TOUCH. It is at 0 volts and may be due to the A10 CPU losing the bonds under the BGA. With regret, believe the A10 is no longer due to the reflow attempt. Can you comment on if the a10 CPU on Aliexpress for the iphone series are the same or not for the ipads? Also, there is a mention of the A10 RAM. Is this a dual layered CPU package? Welcome your comments. We have a reflow BGA workstation that will be deployed on the next attempt (Seamark). Need guidance on the A10 CPU replacement. Does the serial # change once the CPU is replaced? Which tool allows for the proper activation of the logic board after the replacement? The logic board is unlocked but the touch was not working. We replaced the digitizer with a new one - no go. Replaced the Broadcom touch IC - reflowed fine but still not working. The SPI CLK line in diode mode was fine. With regret, did not check the other SPI lines in diode mode after the balls were cleaned on the PCBA. Thanks again.
you got mu subscribe. Thank you for a very organized video and sharing
awesome work 👍🏻
Nice work 👍👍
Love it 🙌🏻
What hot air temps and speeds do you use for CPU removal and replacement?
I explained everything in the video
Hey actually my ipad screen also stopped working, i asked some local service centres and they said ipad screen is dead, but it should first start to get slow or something, because it literally just stopped responding to touch while i was using it, like literally in a snap, a second. So can it be a hardware issue or a software one, plz reply
And yes the ipad is working perfectly fine, no slow no heat just the touch, home button is also working like new, my ipad is 6th gen 2018 ver.
how did you get zxw to work on your mac os?
Crossover
@@AntoineKiriaky10 thx 👍🏻
What causes this issue on an Ipad?
Great, ♥️
I want the scheme, please
Check here
Download iPhone Schematics and Resistance maps and my new Content on RUclips Updated 2022
ruclips.net/video/AnMrEGaWM8g/видео.html
good job bro
where are you loacted im looking for a good soldering tech for my business and would love to send you some work.
Hello, in Ukraine)
Rất hay! ❤
I got an 7th generation with similar no touch issue. Can I send it to you for repair? How much would you charge for this fix? Thanks
Sure, DM me
Good
Wow
👏👏👏👏
👍👍👍
how did you get zxw to work on your mac os?
Crossover (wine)