OMG!!! I think you just saved my life! I bought my 2nd Intex Greywood deluxe July 1. Got it July3. Setup July 4 amd used it at night. Next day e90!!!! I tried everything!!! I called the seller they were supposed to send a “part”. 2 weeks and nothing came. Saw your amazing video. Took the filter apart and surprise the shaft was in pieces!!! Ordered a few from amazon and a new propeller just to have and voila!!!! It’s working!!!! Thank you thank you!!! From this very happy and appreciative single momma!!!
We're just refilling the tub with fingers crossed. Our old impeller shaft was knackered and my husband just fitted the new one. Thank you so much for this very clear instructional video.
Thank you so much!! We have had ours for about 3.5 years and never anything until now… ceramic piece was in 3! Followed your steps and viola!! It works great!!! Thank you thank you!! Great instructions and great tips as you are working! 🥰🥳
Thanks for this video! I've had my Intex Spa for just over 2 years and have gotten the dreaded E90 error a few times. Previously, this issue was resolved simply by cleaning out or replacing the filters. This time I tried everything - cleaning filters, powering on/off, ensuring proper water level and sanitation - nothing fixed the error. Thanks to your in depth video I took apart the pump and everything looked just fine so I reassembled it and voila - It worked suddenly!
Thank you so much a 6 month old spa and the shaft to the pump broke. Fyi a hanger ( wire ) with silicon tape ends is the best fix. Its the same size and will keep your spa running strong.
Thank you for this video. I am a Newby to Spa Repair. And motor repair as well. I have learned a lot watching RUclips. And your video has helped me tremendously! Thanks again
Mane you had the fix o' the week. Thx to your video ive fixed my pump! After following your instructions ive opened up the pump and inside was all kinds of crap. Cleaned it up and reasemmbled it now it works fine even sounds quieter 😆 E90 error has been fixed 💪💪
Those sensors are actually temp sensors. The flow sensors are the plastic gates with the wire coming out to the right of the heater tube. And that heater tube can get nasty and the paint inside can flake off causing a flow restriction
Great advice, thank you. For me the problem wasn't the pump, it was a wire to one of the sensors that had been chewed through by a mouse! Checking everything else led me to the problem though. So 👍
My husband and I just tore ours apart, following all the directions. Easy & instructions from you were on point! Unfortunately it didn’t fix it 😭 Still getting no noise whatsoever and the E90 error. My jets work still 🤷🏼♀️ Any suggestions on what to do next?
Bonjour, suite à un défaut e90, suite à votre vidéo et en remplaçant la tige par une tige filet de de 3mns. Remise en service, et super ça fonction. Cela ne m a coûté que 4, 50€ et mon temps, demontage/remontage à peu prêt 1h. Merci à vous.
Pump works fine, however when I turn on the heat it works for few minutes then shuts off with no error code. I can run the bumbles and everything, just won’t heat up without shutting off. Any suggestions?
Mine had E90 and 8888 replaced shaft with a solid brass. Now air bubbles cycling on and off with radom numbers on the dispaly and constantly beeping. No buttons responded just turns on blower automatically filter doesn't come on only blower.
hola buenas noches. el jacuzzi me salta el automatico dl jacuzzi .cuando pongo para subir la temperatura al poco tiempo de encenderlo .por o demas esta todo pefecto .podria ser las resistencias y donde podria comprarla intex españa me esta poniendo muchas rabas para poder comprarlas .muchas gracias
My impeller looks mint no junk my shaft appears to be ceramic I still get e90 and no noise or attempt to turn on pump at all with it apart on the bench, almost sounds like water is in the pump housing impeller won't spin just gets stuck motor vibrates basically
Can someone please send me a link where i can purchase the pump i did get the rods porcelin exact size on Amazon 2 i am thinking of purchasing more. Now i am lookingfor the pumpi do see other brands but not intex
Hey I’ve had mine for 1 year and now it just shuts off. I’ve cleaned everything checked everything … after it runs for a bit it will completely shut off no error codes… what could be causing this?
I don’t have a link but you can search amazon for an active aqua 550 gph impeller. Once you use this the replacement shafts will no longer fit the impeller as it uses a smaller diameter shaft.
You don’t need to do all that, turn on hot tub make sure the heat button on find the motor tap on it with a handle of a hammer. The propeller is suck I’m not moving ez fix
It is an impeller, not a propeller. If the shaft is broken, it won’t spin. Tapping with a hammer won’t do anything. If there is debris in the motor then that is a different story as I mentioned.
I have replaced the impeller with the 403M model but still no luck. No water flow or sound. The bubbles work so that’s good back to the bucket heater. I did however enjoy your video.
What?! I've used this thing less than 10 times!!!! What a piece of junk. Has new filters. Old ones were not super dirty. Ridiculous. Waste of my precious life's time.
It's garbage. Good for one year then it fall apart. Leaks inside tub. And after a few year not using my pump impeller was fused to the pump. Gave up keeping it in one piece. Drilled it out so I can replace it for hopefully a cheap one. Having a 3d printer so able to do some modifications if needed. Better not buying anything from Intex. Low quality bad service. No warranty no help. Even when it's clear it's manufacturing error. Have several leaks. Welds and inner jet tubes. They send me an offer to buy a new tub for full price. 👍
OMG!!! I think you just saved my life! I bought my 2nd Intex Greywood deluxe July 1. Got it July3. Setup July 4 amd used it at night. Next day e90!!!! I tried everything!!! I called the seller they were supposed to send a “part”. 2 weeks and nothing came. Saw your amazing video. Took the filter apart and surprise the shaft was in pieces!!! Ordered a few from amazon and a new propeller just to have and voila!!!! It’s working!!!! Thank you thank you!!! From this very happy and appreciative single momma!!!
We're just refilling the tub with fingers crossed. Our old impeller shaft was knackered and my husband just fitted the new one. Thank you so much for this very clear instructional video.
Thank you so much!! We have had ours for about 3.5 years and never anything until now… ceramic piece was in 3! Followed your steps and viola!! It works great!!! Thank you thank you!! Great instructions and great tips as you are working! 🥰🥳
Thanks for this video! I've had my Intex Spa for just over 2 years and have gotten the dreaded E90 error a few times. Previously, this issue was resolved simply by cleaning out or replacing the filters. This time I tried everything - cleaning filters, powering on/off, ensuring proper water level and sanitation - nothing fixed the error. Thanks to your in depth video I took apart the pump and everything looked just fine so I reassembled it and voila - It worked suddenly!
Thank you so much a 6 month old spa and the shaft to the pump broke. Fyi a hanger ( wire ) with silicon tape ends is the best fix. Its the same size and will keep your spa running strong.
Thank you for this video. I am a Newby to Spa Repair. And motor repair as well. I have learned a lot watching RUclips. And your video has helped me tremendously!
Thanks again
Me too! I'm fixing lawnmowers and trimmers! Briggs and Stratton mainly!
Mane you had the fix o' the week. Thx to your video ive fixed my pump! After following your instructions ive opened up the pump and inside was all kinds of crap. Cleaned it up and reasemmbled it now it works fine even sounds quieter 😆 E90 error has been fixed 💪💪
Those sensors are actually temp sensors. The flow sensors are the plastic gates with the wire coming out to the right of the heater tube. And that heater tube can get nasty and the paint inside can flake off causing a flow restriction
Where is the heater tube? I have no book or way to get Instructions
I appreciate your clear and concise instructions.
Thank you so much. Were you able to find the sensors? If so, can you share where?
May I ask where you got your impeller from?and the number of it ? Thank you
Great advice, thank you. For me the problem wasn't the pump, it was a wire to one of the sensors that had been chewed through by a mouse! Checking everything else led me to the problem though. So 👍
My husband and I just tore ours apart, following all the directions. Easy & instructions from you were on point! Unfortunately it didn’t fix it 😭 Still getting no noise whatsoever and the E90 error. My jets work still 🤷🏼♀️ Any suggestions on what to do next?
Did you replace the shaft if it was broken? What error code are you getting?
Also try turning it on with no filter. Sometimes the filter restricts water flow and causes a code.
Very clear and good instructions! Thanks for that 😊
Bonjour, suite à un défaut e90, suite à votre vidéo et en remplaçant la tige par une tige filet de de 3mns. Remise en service, et super ça fonction. Cela ne m a coûté que 4, 50€ et mon temps, demontage/remontage à peu prêt 1h. Merci à vous.
Tige filet ?
ou trouver cela …
Merci
Thanks very much. Sorted. Bought some metal rods on Amazon and fitted in minutes.
what is the link to the metal rods?
My hot tub work fine (bubbles/heating etc) but I’m still getting the e-90 error. Anything you can recommend? Thanks so much!
Thank you! Very clear to be able to follow!
Thank you I am learning alot about these hottubs I will be getting one soon
They no longer gave the part on ebay 😢
Where is the link to purchase impeller and shaft?
Can you just clean out the impeller of debris and if works your good?
No code will shut off when running the heat any suggestions? Runs fine with bubbles
Pump works fine, however when I turn on the heat it works for few minutes then shuts off with no error code. I can run the bumbles and everything, just won’t heat up without shutting off. Any suggestions?
I’ve got the same problem. We’re you able to fix?
ruclips.net/video/dN4Ya4GDfzk/видео.html
That link tells you to clean the heater with a baby bottle brush
The heater is painted black inside it comes off and blocks water flow. You need to take it off and clean the paint out if it.
Do you know how to fix an E30 error
Did everything still e90 can it be a lack of power issue
your link don't work ???
Wow. Great video. Thank you.
Hey....is there a link for the sensors?
Mine had E90 and 8888 replaced shaft with a solid brass. Now air bubbles cycling on and off with radom numbers on the dispaly and constantly beeping. No buttons responded just turns on blower automatically filter doesn't come on only blower.
hola buenas noches. el jacuzzi me salta el automatico dl jacuzzi .cuando pongo para subir la temperatura al poco tiempo de encenderlo .por o demas esta todo pefecto .podria ser las resistencias y donde podria comprarla intex españa me esta poniendo muchas rabas para poder comprarlas .muchas gracias
My impeller looks mint no junk my shaft appears to be ceramic I still get e90 and no noise or attempt to turn on pump at all with it apart on the bench, almost sounds like water is in the pump housing impeller won't spin just gets stuck motor vibrates basically
Also had no washers in it either... Maybe I can just try replacing it anyway
Also make sure the shaft is seated properly in the rubber holders on each end.
Get a wite hanger cut to size and cover your ends with silicon tape. Works great
Can someone please send me a link where i can purchase the pump i did get the rods porcelin exact size on Amazon 2 i am thinking of purchasing more. Now i am lookingfor the pumpi do see other brands but not intex
Hey I’ve had mine for 1 year and now it just shuts off. I’ve cleaned everything checked everything … after it runs for a bit it will completely shut off no error codes… what could be causing this?
Is there a timer? Never heard of that
Very useful thank you
Can you provide a link to your replacement impeller?
I don’t have a link but you can search amazon for an active aqua 550 gph impeller. Once you use this the replacement shafts will no longer fit the impeller as it uses a smaller diameter shaft.
You don’t need to do all that, turn on hot tub make sure the heat button on find the motor tap on it with a handle of a hammer. The propeller is suck I’m not moving ez fix
It is an impeller, not a propeller. If the shaft is broken, it won’t spin. Tapping with a hammer won’t do anything. If there is debris in the motor then that is a different story as I mentioned.
Bought one of your shafts and I still can't get the pump to bring in water! Ugh
No filter on either. I had what sounded like a drip coming from the bottom of the unit too.
Check your intake hose
I have replaced the impeller with the 403M model but still no luck. No water flow or sound. The bubbles work so that’s good back to the bucket heater.
I did however enjoy your video.
Probably should have replaced the pump. It’s not that much
Bucket heater can't filter water
Check your water flow sensors. And try starting it up with the filter off. Sometimes the filter restricts water flow and throws a code
Thank you
Españod
Dee’s Nuts…
Quiero que me lo comenten en español
What?! I've used this thing less than 10 times!!!! What a piece of junk. Has new filters. Old ones were not super dirty. Ridiculous. Waste of my precious life's time.
It's garbage.
Good for one year then it fall apart.
Leaks inside tub. And after a few year not using my pump impeller was fused to the pump.
Gave up keeping it in one piece.
Drilled it out so I can replace it for hopefully a cheap one.
Having a 3d printer so able to do some modifications if needed.
Better not buying anything from Intex.
Low quality bad service.
No warranty no help.
Even when it's clear it's manufacturing error.
Have several leaks. Welds and inner jet tubes.
They send me an offer to buy a new tub for full price.
👍