I got a 906bt and a thinktool pros. How can do a steering unlock with those tools? 2011 qx56. No crank. No dash. Scan data shows that steering is lock even though push start is acknowledged by BCM
Hi are you still around I know the video is old but if you are still around I have a question please ,,, 2019 Nissan rogue it starts then dies after one second the mechanic said pcm is telling the fuel injectors to run at 25% he says it needs a computer !!! Can I buy a used one will they be able to program it ? A new one is super expensive
Permission to ask, sir, Autel MaxiDAS DS808, can you program the ecm Nissan march/micra 2018 AT, (the ecm is replaced with a new one) which says the new ecm has no data, it must be programmed by an official dealer, because the old ecm shorted the AT cable, fault code scanned U1000,same as B2193,(whether it can go through the DS808 autel scan) thanks sir
Question I was doing Sam thing today same car but got stuck when doing key session it would ask me for a mobilizer pin before entering the fob key into the slot , what I’m doing wrong or what happened
Hello, I was watching your video and I have a similar problem, when I bought my car I didn't know that they changed the computer and now that I need to do the emission test the vin doesn't match do you think you can help me with that? How can I contact you?
Can you help me out brotha I have a 2005 chrysler 300c 5.7 I need to put another pcm from a junkyard. Will my mk808BT do this, it has an option for "vin write" I believe. Any help would be appreciated.
@@MustangFourSix there are two ways you could get the PIN code you take out the immobilizer module and eeprom it or go to the dealer and give them the VIN number and they can give you the PIN
@markdasparkauto1780 does ktag master version work to eprom it or what does eprom mean I have a ktag in storage but thought It's ve easier woth autel plus I really don't know how to use it
@@MustangFourSix if you do not want to be doing no chip work the best thing to do is go to the dealer buy a new key and they will give you the the PIN code
After replacing a ecm on my 2019 Sentra I have a code p0300 I have replaced spark plugs and coil still car shake in idle Don’t know what else to check Please help 🙏.
If it is a new ECM you will have to download the files from Nissan website I don't think the autel could do that unless if you have a j2534 unless if you have the old ECM you could read the data from the original one and save it and then write the data to the new PCM in autel but you have to downloading the calibration files on Nissan
@@markdasparkauto1780 ECM hard water damage and was replaced with one from eBay. I had the key program to the new ECM but it will not start. I am thinking the ECM should have been programmed to the VIN instead. Can I contact you by phone? Need to move car ASAP.
The security light is on and the car will not crank. When I press the start button I can access the accessories such as power windows dash lights up ect. We have the Autel 908 but when we tried to follow your steps it gets to the area where it tells you to have steering unlocked and battery must be at 12.5v+. And it's grayed out and we cannot access it. We turned the ignition off and we noticed it's accessible, but the key programming will then fail.
@@markdasparkauto1780 no,it's the original. I purchased the car and the owner said they lost the key and they paid a locksmith to program a new one. The locksmith could not program the new key,and the owner found the original. I tried to program the original key but I noticed the complete vin is missing from the computer. It only shows the last three numbers.
Thanks man this was exactly what I was looking for and it worked like a charm
It was useful for me, thank you very much!
You are welcome glad it worked out.
I got a 906bt and a thinktool pros. How can do a steering unlock with those tools?
2011 qx56. No crank. No dash. Scan data shows that steering is lock even though push start is acknowledged by BCM
Hi are you still around I know the video is old but if you are still around I have a question please ,,, 2019 Nissan rogue it starts then dies after one second the mechanic said pcm is telling the fuel injectors to run at 25% he says it needs a computer !!! Can I buy a used one will they be able to program it ? A new one is super expensive
Nice job thank you !!!
thanks man,its the same for nissan juke 2015 with ems3155 kwp 1.2
What are you trying to reprogram the ECM
What type of programmer do I need to look for to make sure that it can program the ECU
Autel with the jbox
Permission to ask, sir, Autel MaxiDAS DS808, can you program the ecm Nissan march/micra 2018 AT, (the ecm is replaced with a new one) which says the new ecm has no data, it must be programmed by an official dealer, because the old ecm shorted the AT cable, fault code scanned U1000,same as B2193,(whether it can go through the DS808 autel scan) thanks sir
No it kind of you got to buy your Nissan subscription and program the ECM the blank way.
Hi i am trying to do same Thing on x trail t32 1.6 dci ecu edc17c84 but i got error 22 with autel. Why i cant change vin
Year
2016 car is running normal but i need to change vin only, do you have fb or whatsappž
I never did 2016 Nissan VIN change yet but I did a 11 a few days ago probably need a programmer to do that on bench.
Question I was doing Sam thing today same car but got stuck when doing key session it would ask me for a mobilizer pin before entering the fob key into the slot , what I’m doing wrong or what happened
Good video my friend perfect
What I realized in some autel
's it l does not do automatic pin code calculation on some cars . All you should do is i d the car and going to NATS.
What kind of autel l are you using
Hello, I was watching your video and I have a similar problem, when I bought my car I didn't know that they changed the computer and now that I need to do the emission test the vin doesn't match do you think you can help me with that? How can I contact you?
markdaspark78@gmail.com
Thank you 🙏
You are welcome
does this make the new ecu work with the original key from the car ?
Yes I use the same original key with the new ECM.
Wow...
Can I use an 08 automatic Sentra ECU for my 2012 manual Sentra?
No you can different set up.
If you get a program ecu do you have to program the key too ? Thank you
Yes the keys have to be program to the BCM.
Does this work for 350z? I swapped my ecu and im getting a no crank no start issue
Same procedure just go into NATS and follow the steps to program the keys do you have ignition key or push button
@@markdasparkauto1780 ignition key
Just follow the procedure I did what kind of scan tool you using
@@markdasparkauto1780 IT WORKED PERFECTLY, I used a used a launch scanner and i finally got my Z back after 3 months of trying to figure it out
Can you help me out brotha I have a 2005 chrysler 300c 5.7 I need to put another pcm from a junkyard. Will my mk808BT do this, it has an option for "vin write" I believe. Any help would be appreciated.
Yes it should be able to do it but you going to need the PIN code the scan tool does not give you the PIN code
@markdasparkauto1780 how can I retrieve this pin code thanks
@@MustangFourSix there are two ways you could get the PIN code you take out the immobilizer module and eeprom it or go to the dealer and give them the VIN number and they can give you the PIN
@markdasparkauto1780 does ktag master version work to eprom it or what does eprom mean I have a ktag in storage but thought It's ve easier woth autel plus I really don't know how to use it
@@MustangFourSix if you do not want to be doing no chip work the best thing to do is go to the dealer buy a new key and they will give you the the PIN code
you can directly in one step by using after replacement function
no you have to set up the NATS (nissan anti theft system) first, once it runs you can rewrite the vin in the pcm
Autel said that they on do bmw and Benz ecu programming?
bmw ok mer coding only
These are tools for professionals, not pretty boys =]
Have you done nissan altima 2019 ECU swaped?
Not yet
@@markdasparkauto1780i tried with ms pro 808 didn't worked only dealer tool for upper model from 2015
Can I programming use ECM by autel?
Depends on what type of ECM what type of car
After replacing a ecm on my 2019 Sentra I have a code p0300 I have replaced spark plugs and coil still car shake in idle
Don’t know what else to check
Please help 🙏.
You had this p0300 before the pcm change
The computer you got is bad as well
Try another 1
Which one software you can ushing for obd2
I use autel for OBD2
Now you can do this with that tool, Doesnt matter if Ecu is locked or not?
No just do nats and write the VIN number .
@@markdasparkauto1780 thanks for ur help dude 🙏🏻
I have infinite qx50 2020 bay new ecm Can do it autel?
If it is a new ECM you will have to download the files from Nissan website I don't think the autel could do that unless if you have a j2534 unless if you have the old ECM you could read the data from the original one and save it and then write the data to the new PCM in autel but you have to downloading the calibration files on Nissan
Will this work on dodge
Yes it could depending on what year
Will this work on 2017 navara
Is that car gas or diesel we do not have that car name here in the USA. start with engine size.
I need this done how much do you charge?
Brooklyn NY
Can you help me with my 2006 Infiniti M35
What's your problem
Can you help with 02 Maxima.
What's the problem
@@markdasparkauto1780 ECM hard water damage and was replaced with one from eBay. I had the key program to the new ECM but it will not start. I am thinking the ECM should have been programmed to the VIN instead. Can I contact you by phone? Need to move car ASAP.
BTW, I am in Queens.
@@X1Y2Z0 what did you use to program the ECM and you do not need no VIN number in those years
@@X1Y2Z0 I am in Brooklyn what is the address in Queens
Scener model name
Autel elite
Need help with 2010 m35x.
What help do you need
The security light is on and the car will not crank. When I press the start button I can access the accessories such as power windows dash lights up ect. We have the Autel 908 but when we tried to follow your steps it gets to the area where it tells you to have steering unlocked and battery must be at 12.5v+. And it's grayed out and we cannot access it. We turned the ignition off and we noticed it's accessible, but the key programming will then fail.
I see you are in NY. I'm also in NYC.
Is it a new key you using
@@markdasparkauto1780 no,it's the original. I purchased the car and the owner said they lost the key and they paid a locksmith to program a new one. The locksmith could not program the new key,and the owner found the original. I tried to program the original key but I noticed the complete vin is missing from the computer. It only shows the last three numbers.
HEY MAN DO YOU KNOW HOW TO DO THE SAMETHING ON A 2011 INFINITI G25??
Is the same process all you have to do is program the key first then you do vin change.