I appreciate how you've obviously learned early that we don't lose anything by giving away our knowledge and expertise. And you keep it real, humble and watchable by having an empty nailer or lacking a couple of inches to other carpenters with their 12"ers. That was a bunch of style from a 4x8!
Hopefully you had a new shop warming party! Your instructions are far superior to any other RUclips wood workers, I appreciate your attention to detail.
Spencer, you’re truly a Master Trim Carpenter. And you’re a great Educator. It would benefit all school districts if they promoted your videos in their Wood Shop Classes. Your videos share Organization, Planning, Math, Safety and Building Science. Young and Old benefit from your messages. Keep going strong into 2024 and beyond!
I love how you put that mini clip of "yes i know i wouldnt have this problem with the Dewalt saw" Literally was thinking that when the message popped up :D
I know this is an older video of yours and you probably already came up with a solution for the off cuts but one thing you could do is build a portable cart/stand for the off cuts. With some heavy duty caster wheels to roll around whenever needed.
I'll echo at least one other comment. You are a huge inspiration. You're talent is nothing short of incredible. I have learned so many things watching your videos. For me, you're attention to detail and how you show it in your videos is truly amazing. I enjoyed every minute of this one. Please continue producing these great learning videos.
Hi Spencer 13:40 To have the best precision in the angles or even when you adjust any type of measurements mechanically, the tolerance between the parts that make up the mechanism must be considered. It is called backlash, so if you come from a 45 degree angle that you achieved starting from a less angle, zero in this case and you make a cut and then want to go to 12 degrees, you must always reduce the angle to a smaller measurement than 12. As you reach from zero ASCENDINGLY to 45.2, you should do the same with 12.2, of course not necessarily reaching zero again but at least 7 degrees and then reach the 12.2. If you exceed the measurement, you must return again a few degrees lower and try again to always achieve 12.2 upwards without going over. If you go down and reach 12.2 degrees directly, when putting effort on the disc, that angle will move depending on the backlash of your saw, which will depend on the quality of the brand and the age of use.
Festool should make a 12” saw. Why didn’t you use your special miter clamps that you’ve used for your door casing to close the miter while you screw it down? I’d need a heavy table saw like a sawstop to make these pieces. My Dewalt contractor saw won’t suffice. Love your attention to detail and techniques for better miters. Watching you cut that miter made me anxious. You got it done right. You were within 1/16 at the bottom 👍Carrying that delicate project to the job site is another stressful event. Perfect tutorial.
On the assembly - Did you consider Dominos on the mitred corners? - Great Video! My safety rule of thumb (no pun intended) for feeding stock through any machine centres around one simple question - Would I let an employee or loved one do this? If the answer is no then I don't do it myself. My auto body repair guy says - "We make a living because people don't follow the instructions".
I’ve just finished 20 similar full framed units for war museum cases, though I used solid Australian Blackbutt which is super hardwood and expensive… this method would have yielded the same result, which will come in handy for a similar mantel I’m just about to undertake
I’m just a beginning woodworker but I learn something every video. I appreciate the no nonsense about links and comments. And I’m looking forward to my Christmas gifts via your best gadgets video.
I was talking to a co-worker that I help flip houses with about your mitre folding and his brother heard me say your name! He perked because I think he owns everything tool you do, lol! It’s amazing how many people I work around know your name and videos! It’s so cool to nerd out with other carpenters about your content! Awesome video, as usual!
Dude, that was amazing! From the start I knew this build was going to have a lot of detail with those flush sides and noses. You are a master carpenter! Very cool build. Great shop too!
On a recent video I criticized your choice of the kapex over the much more affordable and, in my opinion superior, DeWalt slider, some of your followers took me to task saying I "must not invest in my future" because i object to the cost of a festool saw. Well, watching you finish those cuts with a DW jigsaw was quite satisfying to say the least. Having said that, this was a good video and I believe your extra effort on the table saw was worth it's weight in gold.
Haha... That jigsaw work definitely wasn't in the typical "social media facade". For the record, I love the Dewalt slider, it just happened to be that the function and footprint of the kapex fit my needs well in the shop.
Have a Dewalt. Festool or Makita is better for a wall based miter station IMHO. I think the Dewalt is as good or maybe better…but that arm! As I am building out a shop, I am debating as to whether I want a miter station at all (mostly due to space constraints in the wood working area of my shop). Might just use my MFT style assembly table and look into the woodpeckers larger mitering sled. I can dig out the Dewalt from a storage shelf I desperately need it.
I rip the factory edge off with a track saw befor i even use the table saw. because factory edge is not perfect on every sheet. I do this for cabinetry i also use parallel guides and rip other side as well if you are building cabinetry you can stack up 3 sheets and do this for all your rips just clamp it all down and rip 3 or 4 deep in one pass. It prevents tarout and improves production.
Best cure for hiccups I know is to go for a run. Not always possible or convenient but has always worked for me. From one carpenter to another great work and content!
I’m a 4th generation carpenter but no longer work with my tools. I enjoy your videos tremendously. In the commercial world there is zero precision. I am in no way a painter, you couldn’t pay me enough, but I bet those guys love you. It would be even better if you carried at least the trim painting in your number. You probably save them so much labor with your precision I bet they make good money following you.
A little bit of reality on this video. I appreciate that. I’m sure several of us have opinions on what else you could have done but I’d have probably done exactly what you did. I still want to know how you mounted those built ins. 👍👍👍
You sir are my favorite carpentry teacher on youtube. The way you explain the steps you take for each project really sets you apart. Youre a master at what you do, thanks for the lessons
Hi Spencer, I'm near Dayton and have enjoyed your channel for years now. For such a young guy ( I'm 67,so you are very young in my eyes) your knowledge and experience is quite remarkable. It shows everyone just how much you enjoy your trade. Well done😊😊. 2 items. First, I could have sworn that I've seen in your video that you said you didn't run tape along the length of your joints?? Am I mistaken?? Had to think a minute😂😂. I always kept a wet towel nearby when doing glue ups. I had a tendency to do as you, but hated smearing glue all over my jeans. I'm just a priss I guess. Sorry you don't have a place to lean your plywood after cutting. Nice problem to have though, isn't it?? 😂😂 Do you have any tools you'd like to have that you don't?? Would a nice 36" wide belt interest you. Just curious. Have a good weekend. Ron
A wide belt is definitely on my list! There is nuance to miter folding. I explained in a recent video that I prefer not to run tape the length when doing long beams. For my precise work like this I run the tape at length and perpendicular.
The only hiccup remedy that’s ever worked for me is eating a teaspoon of white sugar. It doesn’t taste good, but it works like a charm. Thanks for the video. Excellent instructions and overall design and information. Love your new shop.
I know, right?! It’s so hard having too much room, too much money, too much free time, and too many women. 😂 You’re a good man, Spencer. I totally appreciate your candid, real-world approach to process and work flow. I wonder though, is it a huge time drag to add a glue spreader and a damp rag/paper towel over a finger and the underside of the bench? No sarcasm or criticism, seriously. I look up to you and guys like Adam Savage, for inspiration and feedback. Ideas like yours and “First Order of Retrievability” greatly improve efficiency, labor cost, and improve our lives. Thanks for what you do and your feedback. Keep up the great work, and Merry Christmas!
Just bought the JessEm guides. Have yet had a chance to user them. But this is exactly one of the reasons I wanted them. Great tip on using a scrap piece to feed the stock through.
Festool countersink bit would hugely reduce the effort required putting those mitre screws in 👍 Fantastic work though, and great videos. Best wishes from England 🇬🇧
Spencer, two questions for you, have you ever seen or considered using g a silicone basting brush to spread the glue? They are great because when the glue dries on the bristles they easily peel off and you’re good to use it again. My other question is why not use trim head screws to join the miters? The heads are smaller and they burrow themselves easily into the surface and use a square drive bit to sink them. Your new shop looks so nice, it must be so satisfying to look at it all and know your hard work put it there. I’m awaiting many more top notch projects to come along. Happy New Year, may 2024 bring you good health, happiness and continued prosperity!
As usual nice video. I agree with you on everything you say on how you process your plywood. I do it the same way. As far as not having wall space to stand cut offs up against, make yourself a roll away cart with shelves. You have plenty of room to store it away when not needing it.
39:55 I would be interest to see what the time trade off would be with a tool like the lamello here. Sure there is some upfront time costs getting it dialed in for the miter, but you’d make that back with not having to back fill screw holes and wait for the filler to dry. Plus, a clamex connector would pull that together super tight when you twist with the Allen key.
Build an off-cut cart with nice large casters. You have enough space so the cart can have great hight and full-sheet width as well. I am also sure that your new shop floor does not have major bumps or cracks so rolling it should not be a problem. Use the luxury of your new shop and enjoy the buffer space around you. 😎 When you need the cart, you just pull it from the corner closer to your table saw. Done! On top of that I am sure you could build a cart so dope to be YT share worthy.
This is exactly what I wanted to do over Christmas for my home but I had no clue how deep to make the mitred piece to make it look nice. Your drawing is SO helpful. Thank you so much!
I’m so grateful to learn this. I got lucky with window #1 because the casing happened to be flush, but the next window is proud and I wrecked three pieces of trim trying to get the 4th piece in (and it’s still not in!). I’m now wondering how much of a mess I’d make pulling out what I’ve done? I might just live with it, not sure…
Really like the inside info visual blurbs you are using! If you could leave them up a couple seconds more would be great! Thanks for what you are doing!
I did one of these while ago & didn’t know how I’d do the miter..it was a little bigger than yours but I knew I couldn’t cut the pieces & hope they line up so I miter folded them long first just like you & cut them on my miter saw..it turned out great..it was some special wood from South America so I had no xtra as it was to be stained..this video makes me know I made the right choice 😊thanks Spencer for all your videos
With the new shop have you considered adding a sliding table saw? With all the case work you do seems like it would be a wise decision . Enjoy your videos keep them coming.
You sir are an absolute legend. I am in awe of the fine detail you go into and also the way every element of the process if broken down and optimised like the tape dispenser! I have not long started my journey in the woodworking and carpentry world but have learn so much from your videos and detailed explanations. Each video is crammed with absolute gems and your ability to teach these skills is fantastic. Thank you for your continuing efforts and wishing you a very merry christmas and new year from over here in the UK
This mantel is beautiful! One thing in regards to the kapex, did you look at Makita's corded options? They are rail forward and go up to 12". I've been using the cordless 10" for about 3 years, and it cuts 5" base vertically. It's a heavy one, but it was really close out of the box, and I don't slam it into the detents, so the aluminum plate hasn't been a problem for me. I've been watching your videos for years and have learned a ton from you. Thank you!
Another great video Spencer. Thanks for your honesty about the youtube revenue thing. Good to know how we can support you. Your content is fantastic! How are you liking the Milwaukee nail guns? How much are you running air vs battery when fixing out a house?
Looks great! I'm actually going to suggest this to one of my clients that is looking for that contemporary look. Thanks for this video and for all you do on your channel!
Best channel ever I like that you recommend certain products especially the tape idea to make perfect mitres. Perfect timing as I’m planning (in the works for about 10 yrs now) to add bookshelves and a mantle over an older brick fireplace.
All the great things I’ve seen you do, that final note on screen where you spoke on behalf of all professionals about making a profit and going on with life was the best lol God bless you brother.
I have made a few faux beams for clients and originally saw the miter folding trick from you. Was the best!!! Also, i run a Kapex and one of the few times I’ve been annoyed with it is when it didn’t make it through the whole faux beam! Might have to move myself up to a 12” slider. Great stuff, dude!
Hey Spencer, I just want to commend you on not only your incredible finish carpentry skills, but your comprehensive how-to videos. I’ve learned so much from watching you perform your magic. Thanks dude!
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
THANKS FOR YOUR SUPPORT!!!
Freud LU80R010: 10" Ultimate Plywood & Melamine Blade - amzn.to/4afXNZA (Amazon, Earns Commissions)
Wixey Digital Angle Gauge - amzn.to/46LY6Zb (Amazon, Earns Commissions)
JessEm 04301 Clear-Cut TS Stock Guides - amzn.to/3GziXUX (Amazon, Earns Commissions)
Fast Cap Glu-Bot - amzn.to/3RcMNn6 (Amazon, Earns Commissions)
Milwaukee 23 Ga Pin Nailer - homedepot.sjv.io/LPgdRo (Amazon, Earns Commissions)
Duck HD Clear Packing Tape - 6 Rolls - amzn.to/3NkLMIG (Amazon, Earns Commissions)
Heavy Duty Tape Dispenser - amzn.to/3sZOJHH (Amazon, Earns Commissions)
Just discovered your channel and in 3 videos I have learned more than I have in quite some time.
I appreciate how you've obviously learned early that we don't lose anything by giving away our knowledge and expertise. And you keep it real, humble and watchable by having an empty nailer or lacking a couple of inches to other carpenters with their 12"ers. That was a bunch of style from a 4x8!
Hopefully you had a new shop warming party! Your instructions are far superior to any other RUclips wood workers, I appreciate your attention to detail.
Spencer, you’re truly a Master Trim Carpenter. And you’re a great Educator. It would benefit all school districts if they promoted your videos in their Wood Shop Classes. Your videos share Organization, Planning, Math, Safety and Building Science. Young and Old benefit from your messages. Keep going strong into 2024 and beyond!
Thanks 👍
I love how you put that mini clip of "yes i know i wouldnt have this problem with the Dewalt saw" Literally was thinking that when the message popped up :D
I know this is an older video of yours and you probably already came up with a solution for the off cuts but one thing you could do is build a portable cart/stand for the off cuts. With some heavy duty caster wheels to roll around whenever needed.
I'll echo at least one other comment. You are a huge inspiration. You're talent is nothing short of incredible. I have learned so many things watching your videos. For me, you're attention to detail and how you show it in your videos is truly amazing. I enjoyed every minute of this one. Please continue producing these great learning videos.
The thumbs up ALWAYS gets clicked on before I watch the current video. Nice job as always!
You are the only person I watch on the tube I would hate to see go. And I have bought a few things in your store. Keep the hard work up. Tks
I always buy things through your links, it's literally the least I can do to pay back all the knowledge I gained through your videos. Salud 🍻
I appreciate that!
Hi Spencer
13:40
To have the best precision in the angles or even when you adjust any type of measurements mechanically, the tolerance between the parts that make up the mechanism must be considered.
It is called backlash, so if you come from a 45 degree angle that you achieved starting from a less angle, zero in this case and you make a cut and then want to go to 12 degrees, you must always reduce the angle to a smaller measurement than 12.
As you reach from zero ASCENDINGLY to 45.2, you should do the same with 12.2, of course not necessarily reaching zero again but at least 7 degrees and then reach the 12.2.
If you exceed the measurement, you must return again a few degrees lower and try again to always achieve 12.2 upwards without going over.
If you go down and reach 12.2 degrees directly, when putting effort on the disc, that angle will move depending on the backlash of your saw, which will depend on the quality of the brand and the age of use.
Festool should make a 12” saw. Why didn’t you use your special miter clamps that you’ve used for your door casing to close the miter while you screw it down? I’d need a heavy table saw like a sawstop to make these pieces. My Dewalt contractor saw won’t suffice. Love your attention to detail and techniques for better miters. Watching you cut that miter made me anxious. You got it done right. You were within 1/16 at the bottom 👍Carrying that delicate project to the job site is another stressful event. Perfect tutorial.
I don't even do wood working, but for some reason I watch your videos as entertainment due to your cool/calm demeanor.
On the assembly - Did you consider Dominos on the mitred corners? - Great Video!
My safety rule of thumb (no pun intended) for feeding stock through any machine centres around one simple question - Would I let an employee or loved one do this? If the answer is no then I don't do it myself. My auto body repair guy says - "We make a living because people don't follow the instructions".
That's a great guideline to go by!
That simple guideline applies to a lot of things - but you do have to be able to recognize the danger@@InsiderCarpentry
I’ve just finished 20 similar full framed units for war museum cases, though I used solid Australian Blackbutt which is super hardwood and expensive… this method would have yielded the same result, which will come in handy for a similar mantel I’m just about to undertake
I’m just a beginning woodworker but I learn something every video. I appreciate the no nonsense about links and comments. And I’m looking forward to my Christmas gifts via your best gadgets video.
My number 1 channel to watch. Another great build/tutorial Spencer!
💯
The quest for tighter miters continues. Thanks for your tips and tricks!
One good way to get rid of hiccup is to take a big breath in, hold it in, and then take sip of water.
Great great class as always
Awesome mantel!!
Really appreciate the deep dives on the mantel and bookshelves. Thanks for leveling up the whole craft!
Excellent as always, you are going to cut pin nails if not placed correctly, hammers blades.
You the man
I was talking to a co-worker that I help flip houses with about your mitre folding and his brother heard me say your name! He perked because I think he owns everything tool you do, lol! It’s amazing how many people I work around know your name and videos! It’s so cool to nerd out with other carpenters about your content! Awesome video, as usual!
Dude, that was amazing! From the start I knew this build was going to have a lot of detail with those flush sides and noses. You are a master carpenter! Very cool build. Great shop too!
On a recent video I criticized your choice of the kapex over the much more affordable and, in my opinion superior, DeWalt slider, some of your followers took me to task saying I "must not invest in my future" because i object to the cost of a festool saw. Well, watching you finish those cuts with a DW jigsaw was quite satisfying to say the least. Having said that, this was a good video and I believe your extra effort on the table saw was worth it's weight in gold.
Haha... That jigsaw work definitely wasn't in the typical "social media facade". For the record, I love the Dewalt slider, it just happened to be that the function and footprint of the kapex fit my needs well in the shop.
Have a Dewalt. Festool or Makita is better for a wall based miter station IMHO. I think the Dewalt is as good or maybe better…but that arm!
As I am building out a shop, I am debating as to whether I want a miter station at all (mostly due to space constraints in the wood working area of my shop). Might just use my MFT style assembly table and look into the woodpeckers larger mitering sled.
I can dig out the Dewalt from a storage shelf I desperately need it.
I rip the factory edge off with a track saw befor i even use the table saw. because factory edge is not perfect on every sheet. I do this for cabinetry i also use parallel guides and rip other side as well if you are building cabinetry you can stack up 3 sheets and do this for all your rips just clamp it all down and rip 3 or 4 deep in one pass. It prevents tarout and improves production.
Best cure for hiccups I know is to go for a run. Not always possible or convenient but has always worked for me. From one carpenter to another great work and content!
I’m a 4th generation carpenter but no longer work with my tools. I enjoy your videos tremendously. In the commercial world there is zero precision. I am in no way a painter, you couldn’t pay me enough, but I bet those guys love you. It would be even better if you carried at least the trim painting in your number. You probably save them so much labor with your precision I bet they make good money following you.
This would probably be a grand use of those miter clamps you use for casing/with that bar camp and a few staples that would be solid solid
A little bit of reality on this video. I appreciate that. I’m sure several of us have opinions on what else you could have done but I’d have probably done exactly what you did. I still want to know how you mounted those built ins. 👍👍👍
You sir are my favorite carpentry teacher on youtube. The way you explain the steps you take for each project really sets you apart. Youre a master at what you do, thanks for the lessons
Hi Spencer,
I'm near Dayton and have enjoyed your channel for years now. For such a young guy ( I'm 67,so you are very young in my eyes) your knowledge and experience is quite remarkable. It shows everyone just how much you enjoy your trade. Well done😊😊.
2 items. First, I could have sworn that I've seen in your video that you said you didn't run tape along the length of your joints?? Am I mistaken??
Had to think a minute😂😂. I always kept a wet towel nearby when doing glue ups. I had a tendency to do as you, but hated smearing glue all over my jeans. I'm just a priss I guess. Sorry you don't have a place to lean your plywood after cutting. Nice problem to have though, isn't it?? 😂😂
Do you have any tools you'd like to have that you don't?? Would a nice 36" wide belt interest you. Just curious. Have a good weekend. Ron
A wide belt is definitely on my list!
There is nuance to miter folding. I explained in a recent video that I prefer not to run tape the length when doing long beams. For my precise work like this I run the tape at length and perpendicular.
@@InsiderCarpentry Thanks.
The only hiccup remedy that’s ever worked for me is eating a teaspoon of white sugar. It doesn’t taste good, but it works like a charm. Thanks for the video. Excellent instructions and overall design and information. Love your new shop.
I know, right?! It’s so hard having too much room, too much money, too much free time, and too many women. 😂
You’re a good man, Spencer. I totally appreciate your candid, real-world approach to process and work flow. I wonder though, is it a huge time drag to add a glue spreader and a damp rag/paper towel over a finger and the underside of the bench? No sarcasm or criticism, seriously. I look up to you and guys like Adam Savage, for inspiration and feedback. Ideas like yours and “First Order of Retrievability” greatly improve efficiency, labor cost, and improve our lives.
Thanks for what you do and your feedback. Keep up the great work, and Merry Christmas!
Excellent as usual! When you’re gluing that very narrow miter slot, lift up from the back, like a reverse fold to expose it!
Good thinking!!!
Get yourself the TSO parallel guides, game changer in breaking down plywood.
Even just the square rail is a game changer.
Just bought the JessEm guides. Have yet had a chance to user them. But this is exactly one of the reasons I wanted them. Great tip on using a scrap piece to feed the stock through.
The Great Educator! Optimistic for those bookcase builds and install video...
Festool countersink bit would hugely reduce the effort required putting those mitre screws in 👍
Fantastic work though, and great videos.
Best wishes from England 🇬🇧
Spencer, two questions for you, have you ever seen or considered using g a silicone basting brush to spread the glue? They are great because when the glue dries on the bristles they easily peel off and you’re good to use it again.
My other question is why not use trim head screws to join the miters? The heads are smaller and they burrow themselves easily into the surface and use a square drive bit to sink them.
Your new shop looks so nice, it must be so satisfying to look at it all and know your hard work put it there. I’m awaiting many more top notch projects to come along.
Happy New Year, may 2024 bring you good health, happiness and continued prosperity!
As usual nice video. I agree with you on everything you say on how you process your plywood. I do it the same way. As far as not having wall space to stand cut offs up against, make yourself a roll away cart with shelves. You have plenty of room to store it away when not needing it.
What a great learning video. I love the longer teaching approach.
I am not a professional by any stretch, but I learn so much from your videos. As a DIYer my projects turn out so much better. Thanks so very much.
Beautiful modern looking mantel. I love building mantels!
39:55 I would be interest to see what the time trade off would be with a tool like the lamello here.
Sure there is some upfront time costs getting it dialed in for the miter, but you’d make that back with not having to back fill screw holes and wait for the filler to dry.
Plus, a clamex connector would pull that together super tight when you twist with the Allen key.
Honestly, I didn't want to take the time to try and figure out he alignment and setup with these compound angles. Maybe next time I'll try it.
Thanks!
Awesome and such time given for the details!!!
Build an off-cut cart with nice large casters. You have enough space so the cart can have great hight and full-sheet width as well. I am also sure that your new shop floor does not have major bumps or cracks so rolling it should not be a problem. Use the luxury of your new shop and enjoy the buffer space around you. 😎 When you need the cart, you just pull it from the corner closer to your table saw. Done! On top of that I am sure you could build a cart so dope to be YT share worthy.
This is exactly what I wanted to do over Christmas for my home but I had no clue how deep to make the mitred piece to make it look nice. Your drawing is SO helpful. Thank you so much!
I’m so grateful to learn this. I got lucky with window #1 because the casing happened to be flush, but the next window is proud and I wrecked three pieces of trim trying to get the 4th piece in (and it’s still not in!). I’m now wondering how much of a mess I’d make pulling out what I’ve done? I might just live with it, not sure…
Really like the inside info visual blurbs you are using! If you could leave them up a couple seconds more would be great!
Thanks for what you are doing!
Thanks for the feedback! Will do!
Thanks for another great tutorial. I made my first floating shelves after watching one of your videos. I might have to try this mantel next.
Nice work as always! Enjoy the new shop!
Learned quite a bit. Thank you for the content.
Nice job. I like watching you work. You give me better ideas on how to do things.
Setup a plywood storage pallet rack right behind, perfect place to lean material against😅
Another great class, Spencer. Your attention to details is as refreshing as is your humor!
Oh, and yes, those rollers are in my Amazon cart! Thanks!
run the boards through the jointer between each cut, always have a fresh straight edge.
I did one of these while ago & didn’t know how I’d do the miter..it was a little bigger than yours but I knew I couldn’t cut the pieces & hope they line up so I miter folded them long first just like you & cut them on my miter saw..it turned out great..it was some special wood from South America so I had no xtra as it was to be stained..this video makes me know I made the right choice 😊thanks Spencer for all your videos
Another fantastic video/ project. 👍
Takes me a while to wrap my head around what is 45.3 and what is 44.7. Nice “simple” solution, clearly explained. Thanks.
I recently used your miter fold technique on some floating shelves I built out of oak veneered plywood. Worked like a charm. Thanks for sharing.
Thank you for your excellent teaching style!
Always great to watch. Happy to use your links and love that they automatically go to Amazon Canada now.
Excellent work and tutorial. Thank you.
Awesome work as usual!
Merry Christmas to you and your family.
Great job, Spencer. I learn so much watching your videos and love that fact that you focus on good enough for the real world. Keep the content coming.
you could biscuit join a pair of the backing blocks at each corner.
awesome videos, thanks.
Thanks Spencer! I've switched to TB1 at your recommendation and am loving it! So easy to cleanup and no stiff spots on my jeans. :)
Like always good technique and tricks thanks😉
With the new shop have you considered adding a sliding table saw? With all the case work you do seems like it would be a wise decision . Enjoy your videos keep them coming.
It’s definitely on my radar!
You sir are an absolute legend. I am in awe of the fine detail you go into and also the way every element of the process if broken down and optimised like the tape dispenser! I have not long started my journey in the woodworking and carpentry world but have learn so much from your videos and detailed explanations. Each video is crammed with absolute gems and your ability to teach these skills is fantastic. Thank you for your continuing efforts and wishing you a very merry christmas and new year from over here in the UK
This mantel is beautiful! One thing in regards to the kapex, did you look at Makita's corded options? They are rail forward and go up to 12". I've been using the cordless 10" for about 3 years, and it cuts 5" base vertically. It's a heavy one, but it was really close out of the box, and I don't slam it into the detents, so the aluminum plate hasn't been a problem for me.
I've been watching your videos for years and have learned a ton from you. Thank you!
I wanna GO Home .....love it !!!!! GOOD work !~
So good, Spencer! Thanks for the tips and tricks!
Enjoy watching your videos, lots of good techniques like using the tape for great miter joints.
Great job as always and full of information
Another great video Spencer. Thanks for your honesty about the youtube revenue thing. Good to know how we can support you. Your content is fantastic! How are you liking the Milwaukee nail guns? How much are you running air vs battery when fixing out a house?
I run battery guns for doors, ceiling work, and things like that. Everything else like base and casing we use air.
Crispy is right, nice work
Good work and informative as always
Looks great! I'm actually going to suggest this to one of my clients that is looking for that contemporary look. Thanks for this video and for all you do on your channel!
Love the science behind this mitred joint 🙌
Would it help if u take scrap plywood and overlap ur miter on the inside for backing.? Outrageous mantle build
You have alot of knowledge for someone who seems so young. Thanks for sharing it with the rest of us. Do you ever have time to work on your own home ?
Nope!
Another fantastic job. I really enjoy the videos.
Thank you so much for such an informative video.
Your videos are awesome.
Best channel ever I like that you recommend certain products especially the tape idea to make perfect mitres. Perfect timing as I’m planning (in the works for about 10 yrs now) to add bookshelves and a mantle over an older brick fireplace.
I bet all that tape is nice for tear out on the miter saw
Great work
All the great things I’ve seen you do, that final note on screen where you spoke on behalf of all professionals about making a profit and going on with life was the best lol God bless you brother.
Always a great time watching your videos! I like all the pop up comments that you ad. It reminds me of a mtv “pop up video “ . keep it up!
Great job as always. Why not use finish screws (GRK, etc?)
Trim head screws are the way to go love them up here in Canada. The Robertson screw is a lifesaver watching a Guys drive Phillips. 🥴
Trim screws have very little "pulling/sucking power". They would pull through this plywood very easily without drawing the joint together.
Thank you so much for this video tutorial. Just in time for the style I was looking for to surprise my wife for Christmas.
I have made a few faux beams for clients and originally saw the miter folding trick from you. Was the best!!!
Also, i run a Kapex and one of the few times I’ve been annoyed with it is when it didn’t make it through the whole faux beam! Might have to move myself up to a 12” slider.
Great stuff, dude!
Great video. Thanks.
Hey Spencer,
I just want to commend you on not only your incredible finish carpentry skills, but your comprehensive how-to videos. I’ve learned so much from watching you perform your magic. Thanks dude!
You might look at readily available sheet rock carts for moving sheet goods around