You're supposed to place wood next to or under your wood stove to dry it out before use. Means you have zero need to go outside to get more fuel during the night for at least 2 or 3 days depending on how much heat you actually need.
Yep, that's what we did back during the early 80s as a kid growing up in the middle of nowhere West Virginia. One of my chores was to stack wood about 3-4 feet from the woodstove along a wall close by. The stack of wood lasted us about a week. I'm guessing it was several hundred pounds of wood. It was a single stack about 3 !/2 feet high and about 7 feet long.😂😂
I place waste oil into the lower part. Whilst in the video a brand-new oil bottle can be seen, from which flows perfectly clean, crystal-clear oil. Where do you get that quality waste oil?
A great method of bending small pipes is to pack them full of sand. You can either pinch off the end and then start packing full of sand and then pinch off the other end make your bends and then cut the ends off. What does method you can do some real crazy bends. Great Concepts love your work. Please keep up the good work
any tips on how to get the sand back out again? i was using this for bending some aluminium tubes around a thicker pipe in a spiral which would then be fed with water and a gasburner would turn the water into steam- but it took quite a while to get the sand back out again
Hopefully the sand you use was dry. Cuz if not it's going to be a b**** to get out. I would warm it slowly and drive off any excess water and then just keep tapping it with a screwdriver or a piece of wood and it should work its way out. There is another method but it cost more and if I told you I'd have to that's where you at the super secrets. Punishable by will you know
Salt is a better option then sand simply because to get it out of a thinner tube simply use water to dissolve the salt. Sugar, in my opinion isn’t any good as it burns.
@@anthonyv6962 unlike your comment, I was offering him constructive criticism. He could take it or leave it. I’ll help you out with the definition of Constructive Criticism since you seem to be a little daft. Criticism intended to provide suggestions for improvement without insulting the recipient.
It was pretty simple to follow. The water in the top tank boils and the steam across the burning oil draws more air across, creating the blowtorch effect.
My reply is to some commenters here. This is a build of a very useful tool. That obviously is to be used in an environment that doesn't have a 3D printer, plasma torch or even electricity. If your broke down on the side of some unknown road, no one for miles. All you need is a lighter, a little motor oil & water. This will get wet wood burning for signal fire & warmth. Get it? Good.
What is the diameter of the water nozzle? Good luck, thank you I don't know. There are no designs to follow. Only this video. You will need some time in the workshop to figure out everything about this build. But, for someone who travels on long desolate roads or off-road. This would be a #1 tool to have if you need to camp in a wet environment & all you can collect is wet wood. This tool will dry it enough to get a campfire started. In a wet environment this tool will be the difference between a warm night & a soggy cold night. But, you can't go buy this one yet. You want one, you build it for yourself Good luck & don't burn your hand.
So did I. But in fact, this is a very old trick every user of a steam machine (locomotive, crane, etc.) knows. They use the speed of the steam to improve the draft of the coal fire at the beginning.
Just wanted to chime in and say that water vapor IS NOT seperated molecules. In fact, water is the only naturally occuring element in the world that has three different states (liquid, solid, gas) that are ONLY physical changes in state. In order to seperate the molecules, you can try something like an electrolyzer.
To create steam which increases burn. Everybody that watched video, knows he's burning oil. You might try listening more than talking, and you would have know this and known how useless you comment is. Have a great day.
Does seem to me that many businesses like many I've worked at before all use used oil burners yet none have a tank of water over them to make a boiler to get more heat and spread the heat from the pressure built up. Could maybe even turn a generator. Getting everything you can out of the used oil.
@flatout5815 actually cogeneration is used quite bit in oil and gas, especially for remote installations where power line and substation instalation would be cost prohibitive
its basically a great steam engine. something used from 1700...yet so much tech in it that can be used today for engines..."But there is little money in it, so its a bad idea, so development is not worth it"
I was so amazed by the miracle of creation. Since most of us aren’t welders or metal workers please list the prefabricated equivalents. Looked like that took many hours to make. That same amount of time could have yielded enough fire starter balls made from wood scrap and sawdust and wax, fat, waste oil can even be used if the fire is outside and you don’t cook over the fire for a while which you wouldn’t anyway. Plus why are you lighting that so frequently? Light it at the start of winter and it goes out at the start of spring.
Dude, go away. Most of us are here for the creator aspect of this content. Literally none of us came to find out what we do about wet wood for our wood stove this winter so stfu…🙄😒
It takes energy to turn water into steam & the steam adds nothing to combustion, in fact it robs combustion of oxygen, giving you a larger, reder & yet less intense flame. There is a net reduction in BTU.
@@Doctor-Roboit should make you feel awkward when somebody implies that you have genius.... One can only imagine how small one would feel in the Giant mind of a genius? 😊
Hint: high temp water works better for electrolysis, but you'd have to use (free) solar? energy bc it takes too many watts to heat the water that high ( the higher the temp the better ? ) ... I did this with a microwave oven and got significantly bigger bubbles of size of quarter and even half dollar of O and H faster too, but of course that microwave of 1990 was only 450 watts... compare to tiny bubbles at room temp, and also electrolysis eats away even stainless steel anodes. InventPeaceNotWar
Below is a rocket stove that I designed and built several years ago. I can show you the design if your group is interested. Most important part is the fresh air that I've piped into the centre of the flame. You guys could also integrate the steam into this design.
No matter what you build or how you build it or what design you use you cannot get more BTUs out than BTU combustible, materials, supplied to the burn box.
Great idea! If you heat water beyond the boiling point, it can be used as a burner. Also known as superheated water steam. This device makes practical application of this effect.
After buying pallets....Open them and lay the wood BARK UP...give them time to dry in the sun for a few weeks..2 preferable then replace on pallets and re-tie pallet to keep together neatly and keep pallets together then put roof and siding over and around them and then wood will be fine. Don't use tarps they collect moisture ...STAY WARM..🎉
water H2O splits into hydrogen and oxygen at 800 degrees Celsius. ___ PS: heating (burning water) has been produced for industrial halls for a long time. Heating is also produced (using water cavitation) - is cheaper to produce...
you can make an angle grinder stand, which can be used to accurately cut large tubes as well if you make some mechanism that allows you to turn a tube around while its clamped as well, its especially good for projects where you need many pieces of thin steel or if you cut hardened metal like threaded rods maybe to boost efficiency you wanna insulate the bottom container a bit, maybe make like a disc with holes on the sides so you get the steam contacting a lot more oil? very cool concept, its a waterpowered blowtorch essentially im sure this would turn into a flamethrower if one was to try a regular volatile fuel with this
@@vitorhugomendesdelima-gy4tr The oil is the fuel. The water only provides steam to force air through the burn chamber. It takes the place of a Blower Fan, or a 12 metre flue (Chimney).
I’ve lived I the woods for the last 40 years we normally if the wood is wet just put the next few pieces your going to burn on top of the stovetop to dry out a little more. I’ve used my propane torch to start lots of fires but if you have electricity my favorite is using a heat gun it will fan the fire and dry out the wood it will also start a fire no matches or torches or starting fluids needed just stack up your Kinlin and your wood turn on your heat gun and blow till you have fire it only takes a minute or two and if you’re fire dies down a little just blow it again. Don’t use a hair dryer they will work but the end will melt from the heat in the stove you can get a nice heat gun for $15-20 and they last for years you can also use them to strip paint and other stuff plus you don’t have the smell of burning used oil and when you switch it off it’s off unlike the blow torch in this video you’re going to have to do something with this till it goes out I have a old style blow torch similar to this one it’s a pain to start but you can turn it off when you’re done using it unlike this model good luck and don’t burn your house down 😂
And the wood is still wet! Try to cover the wood so that it doesn't snow on them! Frozen wood is not wet, and if you put it in the stove it will burn better because it also contains water vapor!😎
Hola Amigo soy Inventor , vivo en Chile ... Y le doy gracias a Dios por encontrar tu Canal ... Eres un genio ... Que Dios siga poniendo gracia en ti .... Saludos desde Santiago de Chile ❤
LOL right? we haven't even touched the tip of the iceberg... Harnessing the power of steam/hydrogen will eventually be the answer to energy independence allowing us finally kick big oil to the curb for good, thus allowing us begin fixing the near irreparable damage that they have done simply out of greed. @@bobsaturday4273
@@bobsaturday4273stop being rude. Just say nothing if you don’t like what is said. We all need to get along and not let them win by even not being united on you tube!!!!!
My reply is to some commenters here. This is a build of a very useful tool. That obviously is to be used in an environment that doesn't have a 3D printer, plasma torch or even electricity.
I bet 'the industry' loves you. Use care. For all your fantastic, elegant, genius heating inventions & innovations are exactly the kind of things that have gotten some people 'disappeared'.
Well, unlike thirty years ago when it was much easier to ridicule someone on personal level and to hide information, this video has already been seen probably tens of thousands of times by knowledgable people who know how to replicate this. So, information is already out there and it can only further evolve.
Wut....-_-.....If I were youI would start by learning to build a fire. Tinder, kindling, etc. You can start a fire with one match. I didn't watch past 0:45s because that was so stupid. Necessity is the mother of invention I guess. Beats me.
@@betterl8thannvrHe spent 8 mins didn’t explain this at all. He spent 8 mins making a thing without explanation and didn’t even say how hot it gets. Ummmmm trust me bro
@@shoonsserendipity water doesn't decrease flame, temperature and lack of oxidant (air). However, he jets the steam out of a bigger opening, this will pull a lot of gas with it creating a vacuum inside, fresh air is forced in to equalize pressure, and that air fuels the burn. So water for fire fighting is mostly used to lower the temperature to below the critical reaction temperature. Maybe as steam it can replace a bit of oxygen, but lowering temperature is the most important one. Turning the water into steam costs a lot of energy and hence lowers temperature. Afaik. I am not a fire fighter.
Ever heard of....kindling? Google it, then using your hands, not Google, put crumpled newspaper into the stove first, then place the kindling on top. Light the paper and watch the magic of fire. And please, don't put water on it.
U shouldn't have spoon fed such a simple procedure - they have to have the motivation to seek the answers - u know what they say about unsolicited advice? It's usually a waste of breath because it they haven't yet asked they probably wont appreciate it
hello and respect; I have a question: doesn't the steam that hits the oil fire with such high pressure break down into oxygen and hydrogen, thus also contributing to the combustion ?
No, only electrolysis can break that molecular bond. If mere pressure and heat could break water into hydrogen and oxygen, then volcanic vents under the ocean would be flaming infernos...
Actually yes. The steam reacts with the glowing carbon (soot) producing carbon monoxide and hydrogen. They used to produce coal gas with this reaction.
Or you could have just put the wood you will use in the future next to the fire to dry out each time you use it. And if you need content; make a cutting machine to make smaller fire tinder from one larger piece of wood powered by the previous fire. Or alternatively you could made an electrolyser or a high powered arc from the electricity you clearly have.
Bro, That's exactly what I said too! It's scary because the younger generations are getting sucked into this phony learning. I fear for the future of this society 👎🏻
I like the idea ... And you can reduce temperature of the handle just by putting the handle, on the top side of the handle while only having a big rectangular gap for air input... And a curve slider door to control the airflow...
I came across this and had to watch as I get great enjoyment from watching videos like these and to read some of the comments. I think it is so cool that you have made this. I would love to be able to make something like this but unfortunately I don't have the skill set. But I've always wanted to have a trade in all of these, carpentry, metal work, wielding, electrical and plumbing. I think the education system should make it compulsory for girls to take classes in all of these!
What a solid, go to, tool to have in my go-bag for camping. This is brilliant. I get it, don't need schematics to make my own. I would recommend filing for US Patents on your designs (you never know, something might become a payday). Thanks for sharing your build. Incase the jetter port from the water container might become plugged from foreign material. I will modify your build by adding an adjustable pressure relief cap for saftey, incase left unattended. I have an idiot for a brother. Great build!
He is converting some of the energy in the heat into kinetic energy in the form of steam that creates moving air, and that moving air turbocharges the fire. This is a steam powered turbocharger on a fire. You could use it instead of a bellows to increase the temperature of a bed of coals until it can soften steel. Called a forge.
I would advise not to refill while the stove is actively lit (ignited), your not taking consideration of the back pressure to a handle/refueling port. Sorry, but I think your modification ideas to this design are very dangerous.
You are not starting a fire correctly. You need dry kindling to make the base of the fire. Put a tarp over the top one third of your stacks of firewood to keep the rain and snow of the wood.
The water vapor is used as a carrier for the oil combustion, creating a rocket flame from heavy oil or other combustibles, even wood, it seems. Brilliant idea.
Bro...its amazing...i like It... But I want to know if you can make a water-fired boiler power generator for households. Thank you and I can't wait to see the results 👍👍👍💪💪💪
Interesting video, but who is talking about the physics here? It appears that the stove is burning oil that heats water to a steam jet that increases the velocity of the burning oil/fire/smoke exhaust. Where are we gaining value from the water? The water does not burn here; it's not split to hydrogen/oxygen, or if it did, that takes energy, so there would be no net gain.
Es un verdadero descubrimiento,ideal para los ejércitos y muy útil para el sector RURAL donde todavía no llega el estado y no tienen los medios.FELICITACIONES
Video is about including Steam Jet Vacuum Ejector to increase draft through fuel for more or higher temperature heat by faster burning of fuel. See also Vacuum Ejector article in Wikipedia.
i'm not really an outdoors-y kinda guy, but the first 30 secs where you're trying to light a log with a blow torch makes me wonder, do you live completely without kindling? XD
You're using a gas torch to light wood like that? No wonder you go through so much. Get a small hatchet axe and chop yourself some kindling and tinder. Learn to light a fire properly.
Firestarter I make. TSC Pine Shavings in a 55 gallon steel barrel and pour 5 gallons of free waste oil over bottom half of shavings and repeat at top. Great fire starter.
Pretty cool I’d probably put some type of safety valve in water tank just in case the tube ever got clogged. A unexpected hiss is better than an unexpected bang.
The video is impossible to follow. What exactly you are doing?
He made a blow torch with oil as the fuel and propelled by steam.
They are drunk completely drunks
@@rudyjanke5942no he didn't
Easy to follow
Looks like hes building a self heating coffe mug to me
You're supposed to place wood next to or under your wood stove to dry it out before use. Means you have zero need to go outside to get more fuel during the night for at least 2 or 3 days depending on how much heat you actually need.
But the constructed device itself is very interesting. It can be used on many things.
Genius does not have common sense?
@@Deathproof-Zero1 a no moving parts jet engine? I wonder the thrust coming out is like? got any push?
@@dh2032 What??? 😂
Yep, that's what we did back during the early 80s as a kid growing up in the middle of nowhere West Virginia. One of my chores was to stack wood about 3-4 feet from the woodstove along a wall close by. The stack of wood lasted us about a week. I'm guessing it was several hundred pounds of wood. It was a single stack about 3 !/2 feet high and about 7 feet long.😂😂
I place waste oil into the lower part. Whilst in the video a brand-new oil bottle can be seen, from which flows perfectly clean, crystal-clear oil. Where do you get that quality waste oil?
likely filters the oil his wife uses to cook?
u mechanika...
A great method of bending small pipes is to pack them full of sand. You can either pinch off the end and then start packing full of sand and then pinch off the other end make your bends and then cut the ends off. What does method you can do some real crazy bends. Great Concepts love your work. Please keep up the good work
🤝🤖
any tips on how to get the sand back out again? i was using this for bending some aluminium tubes around a thicker pipe in a spiral which would then be fed with water and a gasburner would turn the water into steam- but it took quite a while to get the sand back out again
Hopefully the sand you use was dry. Cuz if not it's going to be a b**** to get out. I would warm it slowly and drive off any excess water and then just keep tapping it with a screwdriver or a piece of wood and it should work its way out. There is another method but it cost more and if I told you I'd have to that's where you at the super secrets. Punishable by will you know
Salt is a better option then sand simply because to get it out of a thinner tube simply use water to dissolve the salt.
Sugar, in my opinion isn’t any good as it burns.
Salt will work but it gets very expensive on a 3/4 inch copper pipe or half inch. You can see where this can be a problem.
I wish you had given more information throughout the build. Also, it would be helpful to show close-ups while explaining why and what you are doing.
google is free
@@anthonyv6962 unlike your comment, I was offering him constructive criticism. He could take it or leave it. I’ll help you out with the definition of Constructive Criticism since you seem to be a little daft. Criticism intended to provide suggestions for improvement without insulting the recipient.
@@anthonyv6962 Time is not. This suggestion potentially saves time in the future and gets more people to like the creator's videos.
45
It was pretty simple to follow. The water in the top tank boils and the steam across the burning oil draws more air across, creating the blowtorch effect.
My reply is to some commenters here. This is a build of a very useful tool. That obviously is to be used in an environment that doesn't have a 3D printer, plasma torch or even electricity.
If your broke down on the side of some unknown road, no one for miles. All you need is a lighter, a little motor oil & water. This will get wet wood burning for signal fire & warmth.
Get it? Good.
Su nozülü kaç mm çapında?
Kolay gelsin teşekkürler.
What is the diameter of the water nozzle? Good luck, thank you
I don't know. There are no designs to follow. Only this video. You will need some time in the workshop to figure out everything about this build. But, for someone who travels on long desolate roads or off-road. This would be a #1 tool to have if you need to camp in a wet environment & all you can collect is wet wood. This tool will dry it enough to get a campfire started.
In a wet environment this tool will be the difference between a warm night & a soggy cold night.
But, you can't go buy this one yet. You want one, you build it for yourself
Good luck & don't burn your hand.
I can do the same thing with a lighter, a little lighter fluid and newspaper. Am I a genius too?
Brush your teeth and stay out of bars.
😂🙃🤪
I thought the user was going to use water as the fuel. I was very curious as to how the stove separated the H and O.
Yo también pensé lo mismo.
It doesn't. To do it you would need temperature of over 3,000K. The water use is to push the flame out of the nozle.
When you hit water with the right frequency you see it boil, with lots of air coming out, guess what that air is.
So did I. But in fact, this is a very old trick every user of a steam machine (locomotive, crane, etc.) knows. They use the speed of the steam to improve the draft of the coal fire at the beginning.
Just wanted to chime in and say that water vapor IS NOT seperated molecules. In fact, water is the only naturally occuring element in the world that has three different states (liquid, solid, gas) that are ONLY physical changes in state. In order to seperate the molecules, you can try something like an electrolyzer.
It doesn't burn on H2O. He's using oil as a burner.
To create steam which increases burn. Everybody that watched video, knows he's burning oil. You might try listening more than talking, and you would have know this and known how useless you comment is. Have a great day.
Yeah so who the hell suggested he was burning water? Are you trying to convince yourself because you got scared when you thought water was burning….?
@@TxBoi4891how steam increase burn?
Leftists hate this..
@@revmsjtry pouring water on to a burning oil and you'll see.
Great practical use. We use steam the same way with flare stacks for gas fractionation plants and upgraders
🤝🤖
so... whats this good for ?
@bobsaturday4273 using steam to help speed up the velocity of the flaring gas brings in more air and a cleaner burn
Does seem to me that many businesses like many I've worked at before all use used oil burners yet none have a tank of water over them to make a boiler to get more heat and spread the heat from the pressure built up. Could maybe even turn a generator. Getting everything you can out of the used oil.
@flatout5815 actually cogeneration is used quite bit in oil and gas, especially for remote installations where power line and substation instalation would be cost prohibitive
Mr. Robo what exactly you wanted to explain in vedio...?
maybe change the title since your not just using water
the oil just used for activate the steam the real combustion still the high velocity of steam produce from the oil stove heat
I haven't watched the full video but technically you could use water and a solar panel
its basically a great steam engine. something used from 1700...yet so much tech in it that can be used today for engines..."But there is little money in it, so its a bad idea, so development is not worth it"
Pretty straight forward. The vapor state of the water I believe also makes O2 more readily available for the burn. Sweet
I was so amazed by the miracle of creation. Since most of us aren’t welders or metal workers please list the prefabricated equivalents. Looked like that took many hours to make. That same amount of time could have yielded enough fire starter balls made from wood scrap and sawdust and wax, fat, waste oil can even be used if the fire is outside and you don’t cook over the fire for a while which you wouldn’t anyway. Plus why are you lighting that so frequently? Light it at the start of winter and it goes out at the start of spring.
Dude, go away. Most of us are here for the creator aspect of this content. Literally none of us came to find out what we do about wet wood for our wood stove this winter so stfu…🙄😒
And just get a $100 welding machine from Harbor Freight and learn to do what he’s doing. It’s not that difficult
Q tal.... no se que miedo tiene haciendo el video asi, .... pregunto, el uso de agua aumenta el uso de madera ( o sea se consume mas ràpido)
It takes energy to turn water into steam & the steam adds nothing to combustion, in fact it robs combustion of oxygen, giving you a larger, reder & yet less intense flame. There is a net reduction in BTU.
You are a genius in my book Mr. Robo! Thankyou for all your hard work.
I am very pleased that you like my work. Thank you!🤝🤖
so... whats this good for ?
Selling advertising on You Tube!
WHY DON'T YOU GIVE CREDIT TO THE JAPANESE?
THIS IS A CLASSICAL JAPANESE BLOWTORCH?
@@Doctor-Roboit should make you feel awkward when somebody implies that you have genius....
One can only imagine how small one would feel in the Giant mind of a genius?
😊
Hint: high temp water works better for electrolysis, but you'd have to use (free) solar? energy bc it takes too many watts to heat the water that high ( the higher the temp the better ? ) ... I did this with a microwave oven and got significantly bigger bubbles of size of quarter and even half dollar of O and H faster too, but of course that microwave of 1990 was only 450 watts... compare to tiny bubbles at room temp, and also electrolysis eats away even stainless steel anodes. InventPeaceNotWar
The water is wet and does not burn, it must be dried before... 🤣🤣🤣🤣🤣
Below is a rocket stove that I designed and built several years ago. I can show you the design if your group is interested. Most important part is the fresh air that I've piped into the centre of the flame. You guys could also integrate the steam into this design.
I'd love to see your design!
Where can we see this design?
No matter what you build or how you build it or what design you use you cannot get more BTUs out than BTU combustible, materials, supplied to the burn box.
MAN! FINALLY SOMEBODY EXPLAINED HOW IT WORKS. THANKS.
your skills and knowledge are impressive, I love seeing such skillful hands ! it's obvious that you're self-taught ❤💪🇵🇱
I am very pleased that you like my work. Thank you!🤝😊🤖
Great idea!
If you heat water beyond the boiling point, it can be used as a burner. Also known as superheated water steam. This device makes practical application of this effect.
After buying pallets....Open them and lay the wood BARK UP...give them time to dry in the sun for a few weeks..2 preferable then replace on pallets and re-tie pallet to keep together neatly and keep pallets together then put roof and siding over and around them and then wood will be fine. Don't use tarps they collect moisture ...STAY WARM..🎉
Many thanks! I will definitely heed your advice. 🤝🤖
What if you need to use in a couple days vs few weeks? We all know how to dry wood.
Why is everybody so concerned about the wood? The wood was an excuse for us to play with our welding machines and fire. Go away.
water H2O splits into hydrogen and oxygen at 800 degrees Celsius. ___ PS: heating (burning water) has been produced for industrial halls for a long time. Heating is also produced (using water cavitation) - is cheaper to produce...
you can make an angle grinder stand, which can be used to accurately cut large tubes as well if you make some mechanism that allows you to turn a tube around while its clamped as well, its especially good for projects where you need many pieces of thin steel or if you cut hardened metal like threaded rods
maybe to boost efficiency you wanna insulate the bottom container a bit, maybe make like a disc with holes on the sides so you get the steam contacting a lot more oil? very cool concept, its a waterpowered blowtorch essentially
im sure this would turn into a flamethrower if one was to try a regular volatile fuel with this
Many thanks! I will definitely heed your advice. 🤝🤖
There are these things called "Chop Saws."
@@TimeSurfer206 primarily used in the US plus the blades cost a fortune, in europe we use bandsaws rather
Não entendi, se é um fogão à água, para oque tem que por o óleo uzado ??? Kkkkk
@@vitorhugomendesdelima-gy4tr The oil is the fuel. The water only provides steam to force air through the burn chamber.
It takes the place of a Blower Fan, or a 12 metre flue (Chimney).
Who taught you how to make a fire ? Learn how to start a wood fire the right way !
I’ve lived I the woods for the last 40 years we normally if the wood is wet just put the next few pieces your going to burn on top of the stovetop to dry out a little more. I’ve used my propane torch to start lots of fires but if you have electricity my favorite is using a heat gun it will fan the fire and dry out the wood it will also start a fire no matches or torches or starting fluids needed just stack up your Kinlin and your wood turn on your heat gun and blow till you have fire it only takes a minute or two and if you’re fire dies down a little just blow it again. Don’t use a hair dryer they will work but the end will melt from the heat in the stove you can get a nice heat gun for $15-20 and they last for years you can also use them to strip paint and other stuff plus you don’t have the smell of burning used oil and when you switch it off it’s off unlike the blow torch in this video you’re going to have to do something with this till it goes out I have a old style blow torch similar to this one it’s a pain to start but you can turn it off when you’re done using it unlike this model good luck and don’t burn your house down 😂
Many thanks! I will definitely heed your advice. 🤝🤖
He can very easily turn his off. Just keep a larger metal vessel near by to put over top of it to snuff it out. Simple and foolproof
Also no one gives a shit. And no one gave a shit about the wet wood. It was only ever an excuse for us to play with our welding machines and fire…
And the wood is still wet!
Try to cover the wood so that it doesn't snow on them!
Frozen wood is not wet, and if you put it in the stove it will burn better because it also contains water vapor!😎
Well done, excellent use of natural principles given to us by the creator.
😊🤝🤖
so... whats this good for ?
@@bobsaturday4273 Lighting fires.
Great idea , well done !!👍👍👍👍
I am very glad that you liked my idea. Thank you.🤝🤖
You're a good man and people should tell you that every day
Thank you!🤝🤖
Hola Amigo soy Inventor , vivo en Chile ... Y le doy gracias a Dios por encontrar tu Canal ... Eres un genio ... Que Dios siga poniendo gracia en ti .... Saludos desde Santiago de Chile ❤
great stuff! The very old and almost forgotten steam energy/engine/nuclear power concept explained in a children friendly way. I'll try making one.
" almost forgotten steam energy/engine/nuclear power concept " what the heck are you blithering about ???
LOL right? we haven't even touched the tip of the iceberg... Harnessing the power of steam/hydrogen will eventually be the answer to energy independence allowing us finally kick big oil to the curb for good, thus allowing us begin fixing the near irreparable damage that they have done simply out of greed. @@bobsaturday4273
@@bobsaturday4273stop being rude. Just say nothing if you don’t like what is said. We all need to get along and not let them win by even not being united on you tube!!!!!
@truecrime98 He is right, this is some basic ass shit that you learn by middle school.
@@bobsaturday4273 😂😂😂. No hay U235
Pack tubbing with sand or sugar to keep it from collapsing- sugar can get dissolved but will obviously char with flame, so sand is better.
I would love to see more, I just subscribed and those are amazing!
Please share more slow accurate design, love that lil plasma torch
so... whats this good for ? " plasma torch" hardly !
My reply is to some commenters here. This is a build of a very useful tool. That obviously is to be used in an environment that doesn't have a 3D printer, plasma torch or even electricity.
I bet 'the industry' loves you. Use care. For all your fantastic, elegant, genius heating inventions & innovations are exactly the kind of things that have gotten some people 'disappeared'.
Well, unlike thirty years ago when it was much easier to ridicule someone on personal level and to hide information, this video has already been seen probably tens of thousands of times by knowledgable people who know how to replicate this. So, information is already out there and it can only further evolve.
@fortissimoX Woodgas is a 100+ year old technology. Well documented and been used on everything from military trucks in WW1 and 2 and farm tractors.
Fakeistanians
@SilvaDreams elgazositott fa szoval akkor csak fara van szukseg agyfaszparasztok
Muy buen trabajo.Muchas gracias👍👍👍
¡Muchas gracias por apreciar mi trabajo! ¡Me alegra mucho que te gusten mis videos!🤝🤖
As a survivalist, wooded , mountain and urban. Love seeing new ways to keep a good life under the grid or in survival.
Awesome stuff,
🤙🤙🤙 New sub
I am very glad that you liked my idea. Thank you.🤝🤖
Try ordering your wood a year in advance.. it will be dry. Try making kindling..... Try using a fire starter instead of lighting logs with a torch.
Wut....-_-.....If I were youI would start by learning to build a fire. Tinder, kindling, etc. You can start a fire with one match. I didn't watch past 0:45s because that was so stupid. Necessity is the mother of invention I guess. Beats me.
Nice work.
Video perfection:
● solid information
● ingenious innovation
● snazzy soundtrack
● timely knowledge
Thank you very much for appreciating my work! I🤝 am very glad that you like my videos!🤝🤖
Super ! What is the mashine to cut
One of my favorites to make is a great depression hobo travel stove,, I've of course turned and modified for it to be hotter with less fuel use.
🤙🤙🤙
How u improved it
@@smartcookie11 holes at bottom for faster up flow of the fire,,..
Hope it helps,,,,👍😉
Imma like, comment and subscribe! Thanks!!!
Hey! I am very glad that now you are with us! 🤝🤖
Why does the steam enhance the fire? This is great! Thanks!
The steam accelerates the air out of the nozzle, which causes it to pull in more air from the gaps around the top
@@betterl8thannvr It is interesting. Water usually decrease flame. I guess it is not working that way. Thanks!
@@betterl8thannvrHe spent 8 mins didn’t explain this at all. He spent 8 mins making a thing without explanation and didn’t even say how hot it gets. Ummmmm trust me bro
KINDLING!! you absolute tool. KINDLING!!....and dry, room temperature wood.
@@shoonsserendipity water doesn't decrease flame, temperature and lack of oxidant (air). However, he jets the steam out of a bigger opening, this will pull a lot of gas with it creating a vacuum inside, fresh air is forced in to equalize pressure, and that air fuels the burn.
So water for fire fighting is mostly used to lower the temperature to below the critical reaction temperature. Maybe as steam it can replace a bit of oxygen, but lowering temperature is the most important one. Turning the water into steam costs a lot of energy and hence lowers temperature.
Afaik. I am not a fire fighter.
What would u call this?
I like to find if someone is selling it.thanks
I thought it would be a H2 Burner 😢 but maybe you show us soon how to burn water 😊
Quick and easy, got the job done. Saved me searching the menus .
Ever heard of....kindling? Google it, then using your hands, not Google, put crumpled newspaper into the stove first, then place the kindling on top. Light the paper and watch the magic of fire. And please, don't put water on it.
Yep, the way it's meant to be done😅
U shouldn't have spoon fed such a simple procedure - they have to have the motivation to seek the answers - u know what they say about unsolicited advice? It's usually a waste of breath because it they haven't yet asked they probably wont appreciate it
Very rare to have such great music in this kind of videos ✨
hello and respect; I have a question: doesn't the steam that hits the oil fire with such high pressure break down into oxygen and hydrogen, thus also contributing to the combustion ?
No, only electrolysis can break that molecular bond. If mere pressure and heat could break water into hydrogen and oxygen, then volcanic vents under the ocean would be flaming infernos...
Actually yes. The steam reacts with the glowing carbon (soot) producing carbon monoxide and hydrogen. They used to produce coal gas with this reaction.
I ever make in other models, waste oil, water tank, and jet stove...and it work,
I still calculate the efficiency, between LPG and water oil.
Or you could have just put the wood you will use in the future next to the fire to dry out each time you use it. And if you need content; make a cutting machine to make smaller fire tinder from one larger piece of wood powered by the previous fire. Or alternatively you could made an electrolyser or a high powered arc from the electricity you clearly have.
Yeah he could make drying wood much easier but it would mess with his inventions part
Bro, That's exactly what I said too!
It's scary because the younger generations are getting sucked into this phony learning.
I fear for the future of this society 👎🏻
Many mysteries in this creation...
a real piece of work.
😊🤝🤖
I like the idea ... And you can reduce temperature of the handle just by putting the handle, on the top side of the handle while only having a big rectangular gap for air input... And a curve slider door to control the airflow...
I built this burner yesterday and I have to say I'm more than happy. Works very well.
Hello. I am very pleased that my videos are liked and can be useful to someone.🤝🤖
burnernozzle got a max. temperature of 351⁰ Celius
I came across this and had to watch as I get great enjoyment from watching videos like these and to read some of the comments. I think it is so cool that you have made this. I would love to be able to make something like this but unfortunately I don't have the skill set. But I've always wanted to have a trade in all of these, carpentry, metal work, wielding, electrical and plumbing. I think the education system should make it compulsory for girls to take classes in all of these!
I only use the little things around the house:
Pulls out a welding torch 😂
And a plasma cutter.
This is AMAZING!! BRAVO!!!
What a solid, go to, tool to have in my go-bag for camping. This is brilliant.
I get it, don't need schematics to make my own.
I would recommend filing for US Patents on your designs (you never know, something might become a payday).
Thanks for sharing your build.
Incase the jetter port from the water container might become plugged from foreign material. I will modify your build by adding an adjustable pressure relief cap for saftey, incase left unattended. I have an idiot for a brother.
Great build!
These designs have been in the public arena for decades and you'd be unlikely to get a patent granted.
Pour casser la molécule d’eau il faut de l’énergie 😂
Donc c’est un brûleur à eau en physique conventionnel n’est tout simplement PAS POSSIBLE
Čista glupost! Video nije u cijelosti objašnjen (postupak), a i skoro sam zapalio svoju kuću (konačnim "proizvodom")...
He is converting some of the energy in the heat into kinetic energy in the form of steam that creates moving air, and that moving air turbocharges the fire. This is a steam powered turbocharger on a fire. You could use it instead of a bellows to increase the temperature of a bed of coals until it can soften steel. Called a forge.
neat but you should just learn how to start a fire with paper and small sticks. 🍻
Thank you. There must be a way to adjust the exit nozzle size or shape to focus the flame better ...
You could have the handle double as a fueling port. With a second water chamber you could switch them and refuel without relighting
so... whats this good for ?
I would advise not to refill while the stove is actively lit (ignited), your not taking consideration of the back pressure to a handle/refueling port.
Sorry, but I think your modification ideas to this design are very dangerous.
Hi, always love your videos. Thanks for all the hard work and for sharing. All the best from the UK
You are not starting a fire correctly. You need dry kindling to make the base of the fire.
Put a tarp over the top one third of your stacks of firewood to keep the rain and snow of the wood.
Tarps collect moisture. Not a good idea.
Try using kindling, birch bark works well...
That’s the most annoying background music
The water vapor is used as a carrier for the oil combustion, creating a rocket flame from heavy oil or other combustibles, even wood, it seems. Brilliant idea.
This video shows there's always a better and cleaner way to do things, Thanks.
Nice idea and an excellent build
Fantastic Idea ! 👍
Thank you great ideas
Don’t let the fire go out in your furnace. Add wood to it wet or not, it will get hot and dry.
This can be use indoor specially a small room?
Bro...its amazing...i like It... But I want to know if you can make a water-fired boiler power generator for households. Thank you and I can't wait to see the results 👍👍👍💪💪💪
You are amazing Mr. Robo
Thanks a lot! Come again, I will always be glad to see you on my channel! 🤝🤖
Very good DR Robo...but please show the proces how You start fire in this thing...Is not easy and you forgot about it...
If only someone invented smaller pieces of wood ……like uhhhh …… kindling to start a fire 😅
Interesting video, but who is talking about the physics here? It appears that the stove is burning oil that heats water to a steam jet that increases the velocity of the burning oil/fire/smoke exhaust. Where are we gaining value from the water? The water does not burn here; it's not split to hydrogen/oxygen, or if it did, that takes energy, so there would be no net gain.
Are using water vapor is use to heat up the heat value or increase syngas value?
Right now I have subscribed to your channel, interesting ideas you have....
Thanks a lot!
You got my sub. Amazing talent.
nice..i think i got it. The water is vaporised and technically separated into O2 n H hence combustion. Atleast thats what i understand.
Es un verdadero descubrimiento,ideal para los ejércitos y muy útil para el sector RURAL donde todavía no llega el estado y no tienen los medios.FELICITACIONES
How long does it burn?🤔
Your system is really interesting ! A big thank-you ! ! So I subscribe !
Video is about including Steam Jet Vacuum Ejector to increase draft through fuel for more or higher temperature heat by faster burning of fuel. See also Vacuum Ejector article in Wikipedia.
What great inventions ! 👍👍👍
I am very glad that you like my videos! Come again, thanks!🤝🤖
You seem to need a lot of complex machinery for simple tasks to happen. Yes, kindling under the logs works. Drying what you need indoors works.
This stove burns OIL. Sorry if you had to get to the end of the video to find that out.
Yes, very good, but with this design you will quickly melt the steam exit part
this is special steam bomb
Engenious as usual. I’d like buy one.
Thank you for appreciating my work. Unfortunately, I don’t make things for sale; I like to give ideas to people for free.🤝🤖
i'm not really an outdoors-y kinda guy, but the first 30 secs where you're trying to light a log with a blow torch makes me wonder, do you live completely without kindling? XD
You're using a gas torch to light wood like that? No wonder you go through so much.
Get a small hatchet axe and chop yourself some kindling and tinder. Learn to light a fire properly.
Firestarter I make. TSC Pine Shavings in a 55 gallon steel barrel and pour 5 gallons of free waste oil over bottom half of shavings and repeat at top. Great fire starter.
Pretty cool I’d probably put some type of safety valve in water tank just in case the tube ever got clogged. A unexpected hiss is better than an unexpected bang.
Good idea. Thank you!🤝🤖
Crazy project . i like 👍