I use two magnetic locks for a shared toilet with two saperate doors, each door is fitted with a magnetic lock and both locks are connected to a 12 v regulator with a switch placed to be seen easily when entering the toilet. Any early user entering the toilet, immediately press the switch to on and both doors are locked. When finished, switch to off and both doors will unlock. This aims to avoid problems that always occur when the door is left locked from inside the toilet by the first user. Magnetic lock is a passive device and save to use, it works when there is a voltage supply, if there is no supply, the magnet does not operate and the door is open.
Can you make a video short of you kicking the door or pushing it? I’d like to see if someone can kick the door open or ram the door open. Tons of instal videos but no videos of anyone testing its strength
Its a 600 pound electro magnetic lock, which means it requires greater than 600 pounds of force to open it. These are pretty standard on interior doors. Exterior doors are typically 1200 pounds. I've responded to calls where people tried to pry them open and the door was mangled before the lock failed. Only situation I saw was when someone drilled holes in the door and added hooks. Then they attached cable to the tow hitch of their truck and tried to pull the door open. Half the door jam came out, but the lock was still engaged till they cut the power to the lock.
Very good video. the only issue is that you are using cat5e or cat6 for the power into the mag lock, and you are banding 2 wires together for each port. industry standard for a mag lock 12/24 volt should use 18/2 stranded cable. you do not want to split your power going down 2 wires for the same port. cat5e or cat6 is not supported anywhere in the industry for use as power to any mag or strike.
I need help I accidentally shorted the positive wire that goes into the positive terminal by pushing the copper wire away from the negative side of the terminal and a spark happened so now it doesn’t work how do I fix
@@rajbudha4912 open cover door 🚪side magnet 🧲part and there is points connected + and - you should use multi meter to test the perfect voltage must be 12 volts If the voltage⚡️ reach perfectly you try to change magnetic part
@@MediaCreationClub1hello sir my control palan site 12 v battery is disconnect but Access and bail or all puss bottom is working but not look magnet door is not working how to solve plz sir ansar me than you
@@rajbudha4912 first thing check magnetic points it's creating magnet🧲 or not if not you need to check supply voltage⚡️ if still cannot change your 🔋🔌charger
Nice info and instructions thanks
Please make remote control wiring video please 🙏
Thank you so much ❤❤❤❤
I use two magnetic locks for a shared toilet with two saperate doors, each door is fitted with a magnetic lock and both locks are connected to a 12 v regulator with a switch placed to be seen easily when entering the toilet. Any early user entering the toilet, immediately press the switch to on and both doors are locked. When finished, switch to off and both doors will unlock. This aims to avoid problems that always occur when the door is left locked from inside the toilet by the first user. Magnetic lock is a passive device and save to use, it works when there is a voltage supply, if there is no supply, the magnet does not operate and the door is open.
ماشاءاللہ۔۔
Very Nice work...
Wow lovely information about magnetic door👍
I need video of the remote and cabling installation
Brother, Make a video of Connecting the door lock with 2 push buttons - show us the detailed wiring and connections
Yes sure
So nice video
And you are so brilliant work
God bless you
make a full video sir
Nice sharing,,,
Visit my RUclips channel,,,
I’m working on a KT400 ,do all mag locks and press exit buttons wire the same.
Very helpful sir. Thank you
Very helpfull Information thanks very much bro
Wonderful to have on hand for little ones.
Thanks
Very good information
Please make video on connections remote and press button to open door
@@MediaCreationClub1 and also you just show how you pulled cable about cable pulling inside the door frame for mag locks
nice my friend
Nice
I want to know more of these locks,all digital control locks.Iam Eng.k Emmanuel from Kenya
No problem sir, aap Hindi main bhi video bana sakte hai
V informative for us
Nice information
@@MediaCreationClub1 Welcome brother
Can you make a video short of you kicking the door or pushing it? I’d like to see if someone can kick the door open or ram the door open.
Tons of instal videos but no videos of anyone testing its strength
Its a 600 pound electro magnetic lock, which means it requires greater than 600 pounds of force to open it. These are pretty standard on interior doors. Exterior doors are typically 1200 pounds. I've responded to calls where people tried to pry them open and the door was mangled before the lock failed. Only situation I saw was when someone drilled holes in the door and added hooks. Then they attached cable to the tow hitch of their truck and tried to pull the door open. Half the door jam came out, but the lock was still engaged till they cut the power to the lock.
Double Door lock installation kaise kre iska video bhej dijiye
I will upload soon on channel
Great work
Very good video. the only issue is that you are using cat5e or cat6 for the power into the mag lock, and you are banding 2 wires together for each port. industry standard for a mag lock 12/24 volt should use 18/2 stranded cable. you do not want to split your power going down 2 wires for the same port. cat5e or cat6 is not supported anywhere in the industry for use as power to any mag or strike.
good info
can this be turned off when not required like using one bell sitch and other normal switch
Can turn off just switch off the 12 volt adapter giving power to magnet
Wesy yah lock wooden door py Lagta he
Glass py to glass lock hi Lagta he
I want to learn more
good
nice video but you make the hole on the wrong side the hole should be right so cable can easly pass but you make it some how ok tc
Prizs sir
Sir if we have a small gap of 5 mm will it get loccked..... Actually I need it for my one of my projects
Make a video on ACS magnetic door lock installation.
Ok very soon will upload
Can you provide circuit diagram of this circuit
Bro i have change any compny magnet if any prblm
Yes can
@@MediaCreationClub1 only magnet frame can buy or full set
I need help I accidentally shorted the positive wire that goes into the positive terminal by pushing the copper wire away from the negative side of the terminal and a spark happened so now it doesn’t work how do I fix
bro ur videos Excellent
Informative as always
Lk 6
Can it be used on metal doors?
Yes can use metal door, wooden door
Very informative video thanks for sharing
sorry, can I ask the name of product and it's possible to used with out remote control or keycard.
Name of tools
Very informative 👍
Current jane k baad door lock rhta hai kiya
Hernandez Christopher Allen Ronald Taylor Donna
Thank you. How does the lock stay attached to the glass door? It sits on top, why does it not slide?
theres adhesive side as well theres a rubber film that prevents sliding and mere movement
@@darshawnw Thank you.
How to check power megnite look termilel
@@rajbudha4912 open cover door 🚪side magnet 🧲part and there is points connected + and - you should use multi meter to test the perfect voltage must be 12 volts
If the voltage⚡️ reach perfectly you try to change magnetic part
@@MediaCreationClub1 ac supply to convert dc supply megnite Terminal side fuss also
@@MediaCreationClub1 thank you sir suggest me
@@MediaCreationClub1 yes already check the power Dc supply is not sow multi meter but puss bottom working
@@MediaCreationClub1hello sir my control palan site 12 v battery is disconnect but Access and bail or all puss bottom is working but not look magnet door is not working how to solve plz sir ansar me than you
If our cat 6 cable coming from access control panel need another 220 power supply
What is the price of this lock or can I get the link from where I can see this online
👍🙏
Lopez Shirley Hernandez Brian Brown Edward
why all the speeded up action, very hard to follow
Hi, can you please show the diagram of the electric wires?
Never use this cable for Electromagnetic lock, use drop-cable 0.8x4.
Where to buy this ?
Any hardware store or electric door shops
Bhai ye to 1 door ko control kr raha he second wala ka kiya hoga?
Thomas Jose Robinson Cynthia Hernandez Deborah
Wiring diagram please
Lee Michael Brown Michelle Gonzalez David
We need information how conduiting CR AND PB TO
MAGNETIC LOCK
IF YOU HAVE ANY DIAGRAM PLEASE SARE WITH ME
My door is not working meginet look how to repsire
@@rajbudha4912 first thing check magnetic points it's creating magnet🧲 or not if not you need to check supply voltage⚡️ if still cannot change your 🔋🔌charger
Magnetic Terminal is not sow power but puss bottom is working this power chek possible test pen sir
If he will make this video in hindi it will be more helpful and understanding. 😎
Jones David Thomas Linda Lopez James
Please speak in ur native language
Hindi me video dale
*_ok_*
Jones Joseph Hall Ruth Jones William
I need video of the remote and cabling installation
Really
I want to learn more
Johnson John Robinson Brian Clark Matthew