HOW TO: Peugeot 306 door card removal
HTML-код
- Опубликовано: 4 окт 2022
- PEUGEOT 306 - Removing the door card
You may need to do this to repair all sorts of things, replace window motors, add sound deadening, get to the locking mechanisms etc... So hope this assists!
All you need is torx bits (long) and a small screwdriver! - trim removal levers handy too!
---------
Any questions, please feel free to use the comments.
Please ensure you feel confident to complete this task safely, Piggypower takes no responsibility for any consequences from poor workmanship following this guide.
If you think you cannot do this job safely, take it to a professional.
Stay Safe.
Social media stuff:
/ piggypowerofficial
/ piggy.power 
Авто/Мото
Thank you for making a video, and it's informative and good as well! Wouldn't know what to do without it. Absolutely here for the 306 tutorials, not too many of them out there, but it did not hurt that you're handsome as well. LOL :) Please tell me if you're making a video of of the rear third (center) brake light, I've been trying to wrap my head around how to get the led light bar replaced.
Thanks!
What's up with the third brake light??
@@PiggyPowerShoot, just realised the hatch-backs may not have a third brake light? I own a 2002 model 306 Cabriolet. There is a vertical brake light in the top corner of the boot compartment, with about 14 light bulbs. Most of them do not work, so couldn't get my car through the last EU-test because of it. Two screws holds it in place from inside, but there's no actual access to the light bulbs/bar from inside the trunk. I suspect that maybe I have to pry the glass out from the outside - do you happen to know anything about it? :)
@@ambisoulmusic hatchbacks for sure do... But cabriolet is different... Unscrew the screws, should pop out and replace some of the bulbs
You legend. I've been needing this. I didn't request it but have been giving my door cards the eye for quite a while threatening them with the odd screwdriver now and then.
👍🐷😁
and as far as I've seen, or not, Haynes won't tell us which kind of screwdriver. But Piggy did.
Thanks for making this. Your 306 series has helped me out a lot.
No worries 👍🐷😁
A very clearly shown method of disassembling the door upholstery. Super.
👍👍🐷
Thank You.
This video was basically the confirmation i need for how to access the key cylinder. Everything else I found said it was just a screw behind a bung on the door but from this view I am see that it is screwed inside the door.
No worries, hope the repair goes well
I love your man,I actually own one the 98 version, keep educating us
Amazing. What model/spec/engine? Likely be the ph2?
This is so useful! Thanks! Greetings from a fellow 306 owner :)
Glad to help 👍🐷
Thank you for this! My poor interior has been looking rather sad
Time to turn that frown upside down!
Thank you mate that was perfect !!! 👌
You're welcome! 😁
Thanks Mr Piggy I have the sagging door cards in my Ph 2 so I need to get them sorted, have loads of rattles as well so good to know where the might be from,
It feels good to get rid of the rattles 👍🐷
thank you!
You're welcome 🐷👍
Mr Piggy, what a delight to have found this! I just purchased a Ph3 XS 5-door with the upper cloth trim having become unglued. Is there a trick how to get this off and then glue it back on or is the cloth so thin it’ll likely rip into pieces?
Ahh yeah... Buy a new interior haha... Or take door card off and peel it off and then reglue it. Take care though
Great video 👌 I've got to replace the fan blower on my phase 3 , I'm I right that you have to drill a couple of rivet's out that holds the sound isolation in place in the passenger footwell ?
I've never had to drill any rivets out for that, it's usually just clipped in
hi Piggy,
Love your repair videos of the Peugeot 306, maybe you know how to fix when the inner door handle spring breaks. is it a complete new unit or can you repair/replace the spring plus is it a hard job to fix?
luckily it's not the out side handle and it still works but it doesn't pop back in place and sadly it the drivers side.
How do you mean the door handle spring??
@@PiggyPower the inner door handle when opening the car from inside jumps back in position, don't know the part name of it but mine stop doing that after i heard a metal spring or something snap. so i'm curios if these can be replaced or fixed?
Does it still open the door? Its just a rod which connects that handle to the lock mechanism.
Hi, I know what you mean, had the same thing. So, the inner handle has a small metal sprin that pulls the handle back towards the door when you have opened the door from the inside. This spring is located around the hinge of the handle. It is not hard to fix, once you follow the steps of this video. I removed the broken spring in my car because it was interfering with the operation. I had to remove the hinge pin of the handle to do that but it was easy. Now I push the handle back in whenever operating the handle. My plan is to make a trip to the junkyard soon and find another spring.
Great video...but my 306 Cabriolet only has 2 Tork screws behind the electric window switch and just below the door mirror panel. The other holes where you'd expect a bolt (under front end of armrest) and behind the door catch are blank, unlike the 306 in the video. I've followed the rest of the instructions but something is holding the door panel in place...any ideas, anyone? Cheers, David
There's definitely something there under the door handle on all 306s. 👍👍🐷
@@PiggyPower Thanks, I should have watched more closely, it's at 45 degree angle as you said, I couldn't locate it or, at first, see it either. Cheers
👍🐷
Yesterday I was about to drive home, when I thought I would see if my electric passenger window was working (it stopped working before Xmas 2022). Amazingly it decided to work and then it stuttered, came back on again and then would not work to go back up. So now I have to strip the door down with whatever tools I have, and get the motor to move the window before it rains. At least I know the window motor and drivers side switch still work. The passenger door switch illuminates and was working a few months ago, so I assume it still does. The door mirror still moves and works on that side, so I assume the window is getting power too? So it must be some of the other loom wires gone bad perhaps. Apart from wire wiggling and inserting, I could apply 12v straight to the motor to at least get it wound up again.
Have fun 👋😂
@@PiggyPower If you can throw a little advise my way that would be cool. So far I have tested things with a multimeter, and the passenger door switch is working up+down with 12V feed present.
The 2-pin female plug going to the motor/regulator has 12v present as well.
Motor sounded fine before it stopped working the other day, but is not doing anything/no noise etc.
As I am a noob I just very briefly connected 12V the other day direct to the motor from a spare car battery, but got big sparks on the + battery terminal but the cables did not get hot or even warm. No smoke or weird smells from anything, so dunno if I did any harm or not, but the motor did nothing.
I have another model of this 306 2.0 XSi sat in the drive, but its a 3-door phase 3 and so the electric window motor/regulator might not fit my main 5-door phase 2? The Haynes 306 service manual is no help with this, and online parts stores have contradicting compatibility data.
One thing to note is sometime last year the left car stereo speaker went off, so that could be loom related perhaps but if the window switch and motor plug are getting power + ground and switch signals, then I guess all that part is working.
Checked the door to chassis loom?
Did you try reversing the poles on the motor plug?
I'm not sure the 3/5dr modules are the same
@@PiggyPower Actually I did not reverse the polarity when the battery was hooked up directly to the two pins on the motor.
I pulled back the rubber to expose the loom between the door and the car body, and what I could see looked good.
So if the motor/regulator unit on the ph3 car looks right, is it possible to swap only that over to the ph2 car, without having to mess around with the metal silver frame around the glass? Or does it require every part of the frame and motor swapped in one go?
Thanks for your help (long time subber here
😁 )
Not sure what you mean by the frame around the glass?
The glass just has a hole with the plastic bung in it.
The motor and cables are all linked onto the runner, all part of the same thing.
If you've got a spare motor/regulator, even if it doesn't physically fit... Why not just hook it up as part of a diagnosis?
I mean, you could've at least pretended to struggle a little. Some of these were a real pain to remove, omg!
I've never struggled to honest 🐷👍😀🤪