Looked like it was lean as fast as the headers started glowing! I watch alot of these videos and never saw that! Why not start with a 460? Another 50-60hp.
@@coupe545 it's impressive, I respect that. Though bought a 460 with air cobrajet heads for my 94F150 flareside. My father gave it to me. Money talks tho, got a boatload of Windsor stuff, heads, 2 blocks and ones a roller,intake,pistons already on the rods! Tci c4, that'll be the weak like if I get over the 100 powershot! And the weight advantage! Just for causing anyway!!
Sorry mate couldn't really tell what was going on, sounds OK but didn't see any horse power or anything, thanks for your time, all the best to yous and your loved ones
That header on the left side looks real screwed up. Needs to have a straight line header like Mickey Thomson or Richard Petty did via lakester style header. Should be 800 plus HP !!!
What are you talking about those are symmetrical port Ford John Kaase heads kinda like what GM did with the Ls 3 decades after Windsor, Cleveland and 385 series big block Ford 429-460 GM finally did away with siamese ports when the LS came out the 8100 Vortec 496 Chevy truck engine pretty much has 385 series Ford heads on it symmetrical ports on a factory BBC hmmm
I bought a 1970 Galaxie with the 429. $2000. Mid 14s in the 1/4 & 20 miles to a gallon. The 428s got 14 MPG and were slower. I never got why. Unfortunately the frame rusted and the 429 ripped apart. I still wish i kept it. It was a beauty.
Thought I heard piston skirt slap at idle. Engine shouldn't be dancing at idle either. Check for debris in the pan and filter just to be sure. If it's good, run it like a scalded Mustang !
If you look really close at the LS engine it resembles a small block Ford 351 windsor more than a resembles A 350 small block Chev..4 bolt heads, similar oil systems..almost identical bore spacing. Heck even the LS heads will even come within a hair of bolting on a 351W block.. The LS bottom end resembles more of a modular bottom end..Yea superior to the Windsor bottom end.. And the LS heads are light years ahead of the Windsor for efficient easy power. IMO Ford could have been where the LS is in the aftermarket if they'd had done an updated small block with the same bell housing pattern.. OHC build power but people like simplicity.. My 2 cents
THE LS IS COMPLETELY BASED ON FORD DESIGNS. IT'S A REGURGITATED 427 HIGH RISER FORD AKA RAISED PORT 351 WINDSOR. NOT ONE DESIGN ASPECT OF THE OLD SMALL BLOCK CHEVY LIVES IN THE LS. THE LS IS 1000% BASED ON FORD DESIGNS. CHEVY COPIED FORD, BEING THE MOST CRIMINAL THING TO EVER BE PERPETRATED IN THE RACE WORLD. ASK YOURSELF HOW TO EPA ALLOWED THEM TO GET AWAY WITH MAKING A RACE ORIENTATED SMALL BLOCK FORD. GM HAS HAD THE EPA IN THEIR BACK POCKETS FOR DECADES PUTTING PRESSURE ON THEM TO HIGHLY REGULATE FORD AND THIS IS THE REASON FORD WENT MODULAR. ONCE FORD ABANDONED THE PUSHROD MOTOR, IS EXACTLY WHAT GM WANTED SO THEY COULD REDESIGN THEIR SMALL BLOCK USING THE FORD WINDSOR DESIGN PUTTING THE HIGH-RISER PORTS ON IT. SOMETHING FORD COULD HAVE DONE DECADES AGO BUT FROM STRICT EMISSION REGULATIONS PUSHED ON THEM BY THE EPA WITH GM HIDING BEHIND THE CURTAIN IS WHAT TIED FORD DOWN FROM DOING IT.
Ford Mod motors make more power stock heads and blocks breathe better and block strength is by far superior.. LS has excessive internal oil leakage due to cheby junk design another issue GM used “communication ports” or windows between the cylinders, above the main bores, but that leaves very little metal to hold the main bores and cam tunnels in place and can lead to wear problema in the LS the cam and crank are like noodles in there, and it wipes out bearings and lifters. This is why Richard maskin of dart machinery to said that LS was the most pathetic engine he ever worked on I agree if Ford would’ve updated the 351w modernized it the LS swap would never of been a thing.. you are absolute right about people wanting things easy they can’t be bothered to learn dohc engine even if it’s far better for making power… it’s the human way average person doesnt know back then one person built a whole car now there’s 30 different guys for every part.. people don’t like to learn no real passion
@@CoyoteFTW I agree 200% with everything you said.. Even the Amsoil Engine Challenge forbid the modular against the OHV engines. No way they could compete against a modular. My point was the swapping of LSs into Mustangs makes me sick.
Impressive numbers and it sounds awesome! I'm curious why you chose a 429 crank instead of using a 460 crank to get 30 more cubes out of it. Did you use an off the shelf piston or have custom pistons made and did you have to fly-cut the valve reliefs deeper for the P51 heads?
Lsx heads are copied from levelands...now Ive heard it all. Not even in the same zip code. Sure the builder needs all the armchair instructors here lol. Hes running it in .Dynoing a new engine isnt centered around redlining it for a power #
![Tee Grizzley - Blow for Blow (feat. J. Cole) [Official Video]](http://i.ytimg.com/vi/wNLN5xsx5dc/mqdefault.jpg)
Love the 429/460 385 series insane power potential
They havent won anyhthng. Chevs run all over them. And no one can tell me why!
Ford 💪💪💪
@@raginroadrunner 🤣🤣🤣🤣🤣🤣🤣
What an awesome sound.
Sweet Music
What kinda cam specs on this? Sounds healthy but not too crazy. I'm curious to see how it compares to the 598 we are currently putting together.
1:32 #pullin1stgearperiod. 10:04
#secoundgearperiod. 10:07
#finnalgrearperiod.
10:10
Can someone tell me why only 2 of the 4 pipes are glowing on that one bank?
forgive the ignorance, but was it not drawing out the pump shooters?
Carb is not set up right! Fuel is being pulled out of the accelerator nozzles doing the full length or the run. Cab needs anti pull over nozzles!
Super!
Looked like it was lean as fast as the headers started glowing! I watch alot of these videos and never saw that! Why not start with a 460? Another 50-60hp.
That was part of the run in cycle. Couldn't go 460 as couldn't get a forged crank to suit the Ford journal Carillo rods.
@@coupe545 it's impressive, I respect that. Though bought a 460 with air cobrajet heads for my 94F150 flareside. My father gave it to me. Money talks tho, got a boatload of Windsor stuff, heads, 2 blocks and ones a roller,intake,pistons already on the rods! Tci c4, that'll be the weak like if I get over the 100 powershot! And the weight advantage! Just for causing anyway!!
Here’s your new motor she has 300 dyno hours now good luck
Ford should have stuck with this engine.
Chipmunks arrived! 7:12
Is that all???
Sorry mate couldn't really tell what was going on, sounds OK but didn't see any horse power or anything, thanks for your time, all the best to yous and your loved ones
This was mainly a run in session, HP is shown at the end.
The 460 eats crank bearings.
Hello curious what the compression is.
11.4:1
@@coupe545 Cool still easy for pump gas.
@@coupe545 Damn! I Thought It Woulda Been Higher! Great Numbers For a ''Not So Big'' Big Block lol .. Those P51's Are that Good eh?
That header on the left side looks real screwed up. Needs to have a straight line header like Mickey Thomson or Richard Petty did via lakester style header. Should be 800 plus HP !!!
Is what it is, only way it will fit in street car it was made for.
She got broke in right
9.5 Deck SBF?
big block
I think the Blue Cresent's are 10.4
I guessed 750 hp at 7500 rpm...but I think 750 at 7150 is possible.
Built for tough with fast chevy stuff..they should have started using the ls heads a long time ago
man ford always beat chevy .....ford 1 chevy 2.....thats it
What are you talking about those are symmetrical port Ford John Kaase heads kinda like what GM did with the Ls 3 decades after Windsor, Cleveland and 385 series big block Ford 429-460 GM finally did away with siamese ports when the LS came out the 8100 Vortec 496 Chevy truck engine pretty much has 385 series Ford heads on it symmetrical ports on a factory BBC hmmm
@@kevinmarchini5272 You should know by now that chevy boys are pretty dumb.
@@caterpillar6nz310bowtie #1
@@musclebone7875bow ties are for little boys
Just get right after it! That's how you start a dyno video. Very cool. Very real world. This thing really 429 ci?? That is seriously impressive power.
Could you guys tell us what the compression is and if this is going to be a race motor or otherwise thank you!
Wow, I just saw the compression ratio down below. 11.4:1 is simply amazing for a pump gas motor what incredible power are you running 91 or 93 octane?
Australian 98 RON...The equivalent of US 93.
@@saraco429 Thanks!
Really given it a workout
Something screwie going on with that engine, I hope nothing bad, probably fuel pressure or timing
Called break-in
I bought a 1970 Galaxie with the 429. $2000. Mid 14s in the 1/4 & 20 miles to a gallon. The 428s got 14 MPG and were slower. I never got why.
Unfortunately the frame rusted and the 429 ripped apart. I still wish i kept it.
It was a beauty.
Hope mine gets that kind of mileage lol big block twin turbo with a 6 speed
Thought I heard piston skirt slap at idle. Engine shouldn't be dancing at idle either. Check for debris in the pan and filter just to be sure. If it's good, run it like a scalded Mustang !
No doubt they found your assessment of their 715hp engine they built to be totally invaluable 😂
Should have used a cross bolt with bolt main cap.
If you look really close at the LS engine it resembles a small block Ford 351 windsor more than a resembles A 350 small block Chev..4 bolt heads, similar oil systems..almost identical bore spacing. Heck even the LS heads will even come within a hair of bolting on a 351W block.. The LS bottom end resembles more of a modular bottom end..Yea superior to the Windsor bottom end.. And the LS heads are light years ahead of the Windsor for efficient easy power. IMO Ford could have been where the LS is in the aftermarket if they'd had done an updated small block with the same bell housing pattern.. OHC build power but people like simplicity.. My 2 cents
THE LS IS COMPLETELY BASED ON FORD DESIGNS. IT'S A REGURGITATED 427 HIGH RISER FORD AKA RAISED PORT 351 WINDSOR. NOT ONE DESIGN ASPECT OF THE OLD SMALL BLOCK CHEVY LIVES IN THE LS. THE LS IS 1000% BASED ON FORD DESIGNS. CHEVY COPIED FORD, BEING THE MOST CRIMINAL THING TO EVER BE PERPETRATED IN THE RACE WORLD. ASK YOURSELF HOW TO EPA ALLOWED THEM TO GET AWAY WITH MAKING A RACE ORIENTATED SMALL BLOCK FORD. GM HAS HAD THE EPA IN THEIR BACK POCKETS FOR DECADES PUTTING PRESSURE ON THEM TO HIGHLY REGULATE FORD AND THIS IS THE REASON FORD WENT MODULAR. ONCE FORD ABANDONED THE PUSHROD MOTOR, IS EXACTLY WHAT GM WANTED SO THEY COULD REDESIGN THEIR SMALL BLOCK USING THE FORD WINDSOR DESIGN PUTTING THE HIGH-RISER PORTS ON IT. SOMETHING FORD COULD HAVE DONE DECADES AGO BUT FROM STRICT EMISSION REGULATIONS PUSHED ON THEM BY THE EPA WITH GM HIDING BEHIND THE CURTAIN IS WHAT TIED FORD DOWN FROM DOING IT.
block and bottom end was modeled loosely after the Northstar...taken from the LT5
Ford Mod motors make more power stock heads and blocks breathe better and block strength is by far superior.. LS has excessive internal oil leakage due to cheby junk design another issue GM used “communication ports” or windows between the cylinders, above the main bores, but that leaves very little metal to hold the main bores and cam tunnels in place and can lead to wear problema in the LS the cam and crank are like noodles in there, and it wipes out bearings and lifters.
This is why Richard maskin of dart machinery to said that LS was the most pathetic engine he ever worked on
I agree if Ford would’ve updated the 351w modernized it the LS swap would never of been a thing.. you are absolute right about people wanting things easy they can’t be bothered to learn dohc engine even if it’s far better for making power… it’s the human way average person doesnt know back then one person built a whole car now there’s 30 different guys for every part.. people don’t like to learn no real passion
@@CoyoteFTW I agree 200% with everything you said.. Even the Amsoil Engine Challenge forbid the modular against the OHV engines. No way they could compete against a modular. My point was the swapping of LSs into Mustangs makes me sick.
More like the LS copied the Cleveland being they have similar strokes, bore size and deck hight.
Impressive numbers and it sounds awesome! I'm curious why you chose a 429 crank instead of using a 460 crank to get 30 more cubes out of it. Did you use an off the shelf piston or have custom pistons made and did you have to fly-cut the valve reliefs deeper for the P51 heads?
Lsx heads are copied from levelands...now Ive heard it all. Not even in the same zip code.
Sure the builder needs all the armchair instructors here lol.
Hes running it in .Dynoing a new engine isnt centered around redlining it for a power #
TY