For all those who are asking: Access point extends your main internet speed to other places without losing any bandwidth. But it's a must to have it connected via ethernet cable to your modem. Router mode does the same but in this case, via wifi signal, but bandwidth is lost in the way. Access point mode: ___________ _____________ I Modem I ________ ETHERNET CABLE _________ | Access point | (If you use another ethernet cable from her to your devices, you will have exact same internet speed) I____________I |______________| (If you connect from this access point via wifi, bandwidth will be reduced) Router mode is like this ___________ _____________ I Modem I ________ WIFI SIGNAL _________ | Router mode | (Main bandwidth will always be less than the original speed from your modem) I____________I |______________| My recommendation is to always use it as an access point and try to use an ethernet cable from access point to your device, if not possible, there's not much problem. I also recommend using at least CAT6 ethernet cable, if possible use CAT7. Those cables are more than enough for house needs.
An access point cannot obtain internet from a base router purely wirelessly. Therefore after setting up the TPLINK HP 841 as your access point, you need to connect it to the base router with an ETHERNET cable from LAN port of BASE router to WAN port of TPLINK HP 841 (ACCESS POINT ROUTER)! WIRELESSLY if you want to get internet from base to new router you have to set up the new router as a REPEATER/RANGE EXTENDER.
@@BABA-GOMI thanks for this. I currently used my tp link as an access point and connected my mobile phone to it, but i noticed that the connection is slower than my old router
While setting up as Wireless Extender, I'm not able to find my neighbor's access point in the wireless network. All other routers are showing. What could be the issue?
I have a main firewall issuing DHCP IPs and want to connect many 840N devices in Access point mode. Can you have an 840N device in each room setup as an access point and have same SSID as other 840N devices in the other rooms? (would the users reconnect to relevant access point as they move between rooms, any issues likely with interference?)
Hello, I have an Access Point device and I want it puts in credentials itself “User name & password” on a local area network log-in page. So, I needn’t to put it again anymore. Is it possible? Thanks
Hi, I can't access the web-interface. When I first did it (with the same IP you showed) it worked, but I left my TP link in router mode and I can't connect with wifi, only with ethernet cable. And now it shows me a different IP. I tried both with no success. Should I reset both the router and the Tl-840n that I'm using as access point make it work? Thanks!
An access point cannot obtain internet from a base router purely wirelessly. Therefore after setting up the TPLINK HP 841 as your access point, you need to connect it to the base router with an ETHERNET cable from LAN port of BASE router to WAN port of TPLINK HP 841 (ACCESS POINT ROUTER)! WIRELESSLY if you want to get internet from base to new router you have to set up the new router as a REPEATER/RANGE EXTENDER.
Having qos configured on the main router, if i just add an extended router bridging to the main, will extended router access the limited internet that main configured???
@@NETVN82 I have read somewhere, on acccess point device I should plug the lan cable to the yellow port, so I can use the remaining 3 yellow ports for LAN internet. But because this device has access point mode encrypted, I can plug the lan cable to the WAN port but the device will render it as a normal LAN port, so I can use 4 yellow ports as LAN internet. Is this correct? Thanks for your answer.
Hello I had a question, please help If i use the Access Point TP-LINK TL-WA801ND_V1 Wireless N300 And use an outdoor parabolic dish instead of access point antennas, to send the Wifi 2400 MHz frequency, how far can I receive the frequency 100% without loss of quality ???
The TP-LINK TL-WA801ND_V1 is a wireless access point designed for indoor use, and its antennas are optimized for general coverage within a limited range. By replacing the built-in antennas with an outdoor parabolic dish, you can potentially increase the range and focus the signal in a specific direction. Parabolic dishes are known for their ability to provide high-gain and long-range wireless connections. However, achieving a 100% signal without any loss of quality over a specific distance is challenging due to various factors, such as signal attenuation, interference, and environmental conditions. The exact range you can achieve will depend on the following: Transmit Power: The TP-LINK TL-WA801ND_V1 has a maximum transmit power of 20dBm (100mW) according to its specifications. It is worth noting that different regions might have legal restrictions on maximum transmit power. Parabolic Dish Gain: The gain of the parabolic dish will determine its ability to focus the signal and amplify it in a particular direction. Parabolic dishes can have gain values ranging from around 20dB to over 40dB, depending on their size and design. Line of Sight (LOS): The presence of obstacles such as buildings, trees, or other obstructions can significantly reduce the range and quality of the wireless signal. A clear line of sight between the transmitter (parabolic dish) and the receiver (your device) is generally desirable for optimal signal propagation. Environmental Factors: The quality of the wireless signal can be affected by environmental conditions like weather (rain, fog) and electromagnetic interference from other devices operating in the same frequency range. Given these considerations, it is challenging to provide an exact distance or guarantee 100% signal quality without conducting a detailed analysis of the specific environment. However, with a combination of a high-gain parabolic dish and the TP-LINK TL-WA801ND_V1 access point, you may be able to achieve longer distances compared to using the default antennas. It is recommended to consult with experts in wireless networking or conduct field tests in your specific environment to determine the achievable range and signal quality.
After doing this, internet working fine through the access point but unable to access the router settings( cant see the routers IP address, default IP not working). The original IP address of the base is showing even after connecting to the new router.
It is in Same Network or Different network... Because We Want Base Router With Access point Router With Ethernet cable & in Same Network For Ip Messenger
@@NETVN82 Thanks for the fast response! Also one more question? Do I also have to disable DHCP by assigning a static IP address? Most other tutorials recommend this for some reason...
Did you connect it to your main modem via LAN cable? If you don't you will never get the internet. If you want to connect them wirelessly, you need to change to router mode.
Access point extends your main internet speed to other places without losing any bandwidth. But it's a must to have it connected via ethernet cable to your modem. Router mode does the same but in this case, via wifi signal, but bandwidth is lost in the way. Access point mode: _____________ _______________ I Modem I __________ ETHERNET CABLE ___________ | Access point | (If you use another ethernet cable from her to your devices, you will have exact same internet speed) I____________I |______________| (If you connect from this access point via wifi, bandwidth will be reduced) Router mode is like this _____________ _______________ I Modem I __________ WIFI SIGNAL ___________ | Router mode | (Main bandwidth will always be less than the original speed from your modem) I____________I |______________| My recommendation is to always use it as an access point and try to use an ethernet cable from access point to your device, if not possible, there's not much problem. I also recommend using at least CAT6 ethernet cable, if possible use CAT7. Those cables are more than enough for house needs.
Les gars aidez moi svp.comment faire pour empêcher les gens de ne pas scanner mon wifi tp-link. Quelqu'un peut me faire une vidéo détaillée par rapport à ça, svp.
No.. you can't bridge through router to router.... The first device in the topology must be a Combo ..and set as ADSL mode.... Then check it to bridge mode....
Please help me , I have WiFi , I have another router transformed an access point , but the Browser in labtop give me this message (this connection in not private ) , but when I close this router (access point) , the search engine work well with not this message , what solutions please
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
![[#2024MAMA] BIGBANG (빅뱅) - 뱅뱅뱅 (BANG BANG BANG) + FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/EQsYfiPR9uM/mqdefault.jpg)
For all those who are asking:
Access point extends your main internet speed to other places without losing any bandwidth. But it's a must to have it connected via ethernet cable to your modem.
Router mode does the same but in this case, via wifi signal, but bandwidth is lost in the way.
Access point mode:
___________ _____________
I Modem I ________ ETHERNET CABLE _________ | Access point | (If you use another ethernet cable from her to your devices, you will have exact same internet speed)
I____________I |______________| (If you connect from this access point via wifi, bandwidth will be reduced)
Router mode is like this
___________ _____________
I Modem I ________ WIFI SIGNAL _________ | Router mode |
(Main bandwidth will always be less than the original speed from your modem)
I____________I |______________|
My recommendation is to always use it as an access point and try to use an ethernet cable from access point to your device, if not possible, there's not much problem.
I also recommend using at least CAT6 ethernet cable, if possible use CAT7.
Those cables are more than enough for house needs.
Do you connect it LAN to LAN or LAN (modem) to WAN (router)?
Thank u for this!!!!!!!
@@jennavendano It should be LAN to LAN
An access point cannot obtain internet from a base router purely wirelessly. Therefore after setting up the TPLINK HP 841 as your access point, you need to connect it to the base router with an ETHERNET cable from LAN port of BASE router to WAN port of TPLINK HP 841 (ACCESS POINT ROUTER)!
WIRELESSLY if you want to get internet from base to new router you have to set up the new router as a REPEATER/RANGE EXTENDER.
Can i still have internet acces even if my base router is turned off? But connected by a lan cable from my base to wan of my tp link
@@chini2W0 No. Base needs to be On. I haven't tried it, try n see, but it seems logical that the AP Router will not recieve if the base R is Off.
@@BABA-GOMI thanks for this. I currently used my tp link as an access point and connected my mobile phone to it, but i noticed that the connection is slower than my old router
What about IP address settings on the TPLink router (configured as an AP). I am having some trouble with an AP. It just suddenly stopped working!
Can we change the password of rangè extender? In tp link
Hello, I just want to ask what is the difference of the 'Wireless Router' mode and the 'Access Point' mode? I'm a little confused what to choose.😅
Do I need to disable DHCP on the second router?
is it a must to connect with lan cable ? can i connect it with router wireless?
Once I AP mode you can't just connect via Physical LAN ports
What Will Happen If U Choose Access Point?
Do i connect this router to the main router first or just connect straight to my laptop to change the configuration
While setting up as Wireless Extender, I'm not able to find my neighbor's access point in the wireless network. All other routers are showing. What could be the issue?
Bình thường nên để chế độ acesspoint hay router anh nhỉ
nên để access point sẽ cho nhiều người dùng hơn bạn ạ,nhưng khi cần cài đặt hay đổi mật khẩu thì hơi khó
Cho router về chế độ ap mode này thì dây lan cắm vào cổng wan hay lan trên router ạ
cổng nào cũng được, nhưng tốt nhất nên cắm vào cổng WAN để đánh dấu đầu vào, cũng như khi mất cấu hình không bị lỗi mạng xảy ra
@@NETVN82 ruclips.net/video/TyK4qpJQI3g/видео.html
Như thế này ý ạ
Gan ,kalau wifi tembak itu masih bayar bulanan gak?
Pakai tenda outdor di luar
Ficou bom mas incompleto. Como ficam os cabos atrás do roteador???
Cara vc é foda! Resolveu meu problema sem dar uma palavra.
I have a main firewall issuing DHCP IPs and want to connect many 840N devices in Access point mode. Can you have an 840N device in each room setup as an access point and have same SSID as other 840N devices in the other rooms? (would the users reconnect to relevant access point as they move between rooms, any issues likely with interference?)
How to create/connect 2 access point? The other one is connected and the other one is not, i mean its already wired but no internet connection.
If i set up access point mode, can I still get internet connection using the lan ports?
Yes
@@agonzalez1914 thank you for that info.
News tp-link you don´t need change ip adress, if you did you can´t acess settings page
Hello,
I have an Access Point device and I want it puts in credentials itself “User name & password” on a local area network log-in page. So, I needn’t to put it again anymore. Is it possible?
Thanks
Hi, I can't access the web-interface. When I first did it (with the same IP you showed) it worked, but I left my TP link in router mode and I can't connect with wifi, only with ethernet cable. And now it shows me a different IP. I tried both with no success. Should I reset both the router and the Tl-840n that I'm using as access point make it work? Thanks!
After installation, you find the ip on the primary router, the dhcp part
An access point cannot obtain internet from a base router purely wirelessly. Therefore after setting up the TPLINK HP 841 as your access point, you need to connect it to the base router with an ETHERNET cable from LAN port of BASE router to WAN port of TPLINK HP 841 (ACCESS POINT ROUTER)!
WIRELESSLY if you want to get internet from base to new router you have to set up the new router as a REPEATER/RANGE EXTENDER.
pwede po ba ma change to 5ghz ubg ganitong router?
I done this process but my Wi-Fi not showing name and router is on what can I do then
if i had 4 ports? can all the ports works? and the wifi?
I can't connect my pc to my access point using the wifi receiver dongle. What should I do? It says failed to obtain details.
How to set up a tp link to work for me ..as with WIFI and to have an output on RJ45 ...
and how that mode has a name
why do we choose ACCESSPOINT ? Cant we choose wireless?
Does the qos function still accessible if in access point mode?
nope
Having qos configured on the main router, if i just add an extended router bridging to the main, will extended router access the limited internet that main configured???
Goid Job, like and subscription. ❤🎉
Why you're disable dhcp?
WHAT ABOUT CHANGE OF IP ADDRESS ?
How to connect tp link Archer C50 AC1200 through access point mode wirelessly
If I use Access Point, can I use internet from the 4 yellow LAN ports?
You use 4 normal yellow port
@@NETVN82 I have read somewhere, on acccess point device I should plug the lan cable to the yellow port, so I can use the remaining 3 yellow ports for LAN internet. But because this device has access point mode encrypted, I can plug the lan cable to the WAN port but the device will render it as a normal LAN port, so I can use 4 yellow ports as LAN internet. Is this correct? Thanks for your answer.
Bisa di config point tonpoint nggak ?
How to force it to set ip range to the router 192.168.1.x
Not 192.168.0.x
i would like to know how to setup VLANS ON
TP-Link Wireless N Router WR840N
Model No. TL-WR840N
PLEASE!!!!!!!
Hello bro I'm using tp link router N840 as access point. I want to know whear will I plug the cabl .in main port or
You can plug in any port
@@NETVN82 wan or lan port? since we are using the access point.
@@josephvillanueva4991 lan port, don't use wan
Hello
I had a question, please help
If i use the Access Point TP-LINK TL-WA801ND_V1 Wireless N300 And use an outdoor parabolic dish instead of access point antennas, to send the Wifi 2400 MHz frequency, how far can I receive the frequency 100% without loss of quality ???
The TP-LINK TL-WA801ND_V1 is a wireless access point designed for indoor use, and its antennas are optimized for general coverage within a limited range. By replacing the built-in antennas with an outdoor parabolic dish, you can potentially increase the range and focus the signal in a specific direction. Parabolic dishes are known for their ability to provide high-gain and long-range wireless connections.
However, achieving a 100% signal without any loss of quality over a specific distance is challenging due to various factors, such as signal attenuation, interference, and environmental conditions. The exact range you can achieve will depend on the following:
Transmit Power: The TP-LINK TL-WA801ND_V1 has a maximum transmit power of 20dBm (100mW) according to its specifications. It is worth noting that different regions might have legal restrictions on maximum transmit power.
Parabolic Dish Gain: The gain of the parabolic dish will determine its ability to focus the signal and amplify it in a particular direction. Parabolic dishes can have gain values ranging from around 20dB to over 40dB, depending on their size and design.
Line of Sight (LOS): The presence of obstacles such as buildings, trees, or other obstructions can significantly reduce the range and quality of the wireless signal. A clear line of sight between the transmitter (parabolic dish) and the receiver (your device) is generally desirable for optimal signal propagation.
Environmental Factors: The quality of the wireless signal can be affected by environmental conditions like weather (rain, fog) and electromagnetic interference from other devices operating in the same frequency range.
Given these considerations, it is challenging to provide an exact distance or guarantee 100% signal quality without conducting a detailed analysis of the specific environment. However, with a combination of a high-gain parabolic dish and the TP-LINK TL-WA801ND_V1 access point, you may be able to achieve longer distances compared to using the default antennas. It is recommended to consult with experts in wireless networking or conduct field tests in your specific environment to determine the achievable range and signal quality.
Permisi gan, semisal kita aktifkan Guest Network ( Ssid ke 2 ) nah terus kita mau hidden ssid ke 2 itu apakah bisa?
You can
After doing this, internet working fine through the access point but unable to access the router settings( cant see the routers IP address, default IP not working). The original IP address of the base is showing even after connecting to the new router.
TRY TPLINKWIFI.NET
It is in Same Network or Different network... Because We Want Base Router With Access point Router With Ethernet cable & in Same Network For Ip Messenger
Same network with different Lan subnet
WISP MODE ?
Bagaimana cara mendapatkan tahu ip nya ya? Seperti di 0:26
Trims
What port should I use for insertion of C6 cable to the access point? LAN or WAN?
you can use both, but i recommend wan
@@NETVN82 Thanks for the fast response!
Also one more question? Do I also have to disable DHCP by assigning a static IP address? Most other tutorials recommend this for some reason...
Yo pongo admin y anda q me deja entrar
dari router bawaan port 1 lalu ke wr940 port internet?
HOW TO TP LINK CONFIGRATION OF DIGISOL
Thanks
Welcome
bang, beda nya mode AP sm wireless router itu ap?yg d bawah komentar kurang jelas
AP mode works better and does not grant ip address
I use access point mode, but don't have internet connection
Did you connect it to your main modem via LAN cable? If you don't you will never get the internet. If you want to connect them wirelessly, you need to change to router mode.
Thanks working
Bang cara buat mode unrestricted di tp link bang
@robotnob seting aja Range Extender
Hi bro what is access point mode? Because I don't understand
Access point extends your main internet speed to other places without losing any bandwidth. But it's a must to have it connected via ethernet cable to your modem.
Router mode does the same but in this case, via wifi signal, but bandwidth is lost in the way.
Access point mode:
_____________ _______________
I Modem I __________ ETHERNET CABLE ___________ | Access point | (If you use another ethernet cable from her to your devices, you will have exact same internet speed)
I____________I |______________| (If you connect from this access point via wifi, bandwidth will be reduced)
Router mode is like this
_____________ _______________
I Modem I __________ WIFI SIGNAL ___________ | Router mode |
(Main bandwidth will always be less than the original speed from your modem)
I____________I |______________|
My recommendation is to always use it as an access point and try to use an ethernet cable from access point to your device, if not possible, there's not much problem.
I also recommend using at least CAT6 ethernet cable, if possible use CAT7.
Those cables are more than enough for house needs.
My router has no operation same model 😢
thanks
Thanks mate
Happy to help
Thank U
Welcome
thanks a lot
Not working bro pls help me
Puedes Bloquear páginas o sitios web en este Router? Porfavor !!
mode operasi wireless router pake kabel lan mode access point pake kabel lan beda nya dimana? hanya mode extender yg g a pake kabel lan
Dalam mode AP, perangkat tidak menyediakan IP. Mode router, tingkat perangkat IP
@@NETVN82 Do you need to turn off AP DHCP as well...If I connect through combo?
Les gars aidez moi svp.comment faire pour empêcher les gens de ne pas scanner mon wifi tp-link. Quelqu'un peut me faire une vidéo détaillée par rapport à ça, svp.
Hello, can i bridge other router on my main using router mode?
No.. you can't bridge through router to router....
The first device in the topology must be a Combo ..and set as ADSL mode.... Then check it to bridge mode....
Please help me , I have WiFi , I have another router transformed an access point , but the Browser in labtop give me this message (this connection in not private ) , but when I close this router (access point) , the search engine work well with not this message , what solutions please
Esse modelo wr840n
Não tem opção "modo de operação"
Tenho esse roteador e tenho o wr849n q é o modelo q tem a opção "modo de operação "
Atualize o firmware
my router crashed after choosing access point . I need to change my region
Thanks ♥️
Bikin tutorial yg jelas bosss... Asal upload aja kau..
Bro me haces un favorr?
wrong setting
Show ALL Wi-Fi password with only 1 CMD ruclips.net/video/RC1GNOu_4YU/видео.html
thanks
Welcome