Awesome set up and always did give a futuristic look and having MOA’S are the best I’ve been wanting to build a Frankenstein scaler with those or the new sparc axels with torque vectoring and tank mode🤩
Thanks for the great informative vid. I am on the verge of getting my first competitive level crawler more out of love for this type of machine and just genuine interest! I am trying to decide on the electronics! This helps!
Hello, thanks for your work, could you show a video with those motors in action? I have an XR10 and I need to change engines and I don't know which one to decide on, this option would be ideal.
Thank you so much for posting this! I have the exact same truck and exact same electronics, except I’m using the Fly sky, noble nb4. I just had a question are you running the front motor let’s say in the throttle slot and the second motor wire into the auxiliary slot? And then you were mixing those two channels? Thanks in advance.
Thanks for this video :) I just picked up a Bully2 and a couple of fusion 2300s. Very timely I found your channel/video :) I’m planning on using a Holmes svh500lp for added clearance. Any advice on the best way to power it up. I’d hate to hurt anything, any help is appreciated. Thanks again :)
Maybe you can help Sir I just got a dx5c and trying to set the rear stear up on my capra like it is on the rtr tx do you know if it's possible? Just getting into the crawling Hobby I didn't have any issue setting it up on the scx6 honcho but I would really like to be able to point and lock the rears independent from the fronts on the capra like I could on the dx3
I would like to see you set that up with four wheel steering and be able to steer the front and the rear independently from one another. Is it possible to do that with the radio that you are using?
The remote does have a 4ws function and you can do what you described. I won’t be doing that with this truck as it is for comps and rear steer is not allowed
I was going to ask the same question. Looks like he isn’t answering any questions though. The video is basically a wast of time. It actually creates more questions than it answers.
@@DESOUSAB the fusion 2300 is slightly smaller mate. All I had to do was bend the links on one side to accommodate then wind out the coupler slightly to make up the difference
Can you please show us an in depth video of how you made those HW Fusion motors fit? I am looking at close to $500 worth of HW Fusions on my worktop, and they DO NOT fit properly, contrary to what your video shows...
@@Twin_Hammers That would be great. Just working on setting up the alternative Revolver 540 V3/Mamba Micro X set. Originally grabbed BR Dual for that set up not realizing it was only for brushed motors, and the Revolvers are brushless - doh! If I could get the Fusions to fit, that would be my first choice, though...
@@Twin_Hammers Hey - touching back with you regarding fitting the Fusion motors in the Bully II. I can't get the links to clear the end of the motor...
Awesome set up and always did give a futuristic look and having MOA’S are the best I’ve been wanting to build a Frankenstein scaler with those or the new sparc axels with torque vectoring and tank mode🤩
Thanks for the great informative vid. I am on the verge of getting my first competitive level crawler more out of love for this type of machine and just genuine interest! I am trying to decide on the electronics! This helps!
Killer info Tyler..😎.. I'm sure this will help many with the dx5 and twin fusions..👍
Just wanna say thanks for this video. I was able to use it on my bully with twin hw1080 escs.
THANKS for the info! worked perfectly with my rugged!
Nice job Tyler.
great info and cool remote setup
Sick setup 😝👍🏻🔥😎🔥💪🏻
So awesome thanks
Super helpful 👌
Nice! Thank you! 👍👍
Thanks for the info
Great instructional vid.
Did those fusion motors fit without any mods ?
Hello, thanks for your work, could you show a video with those motors in action?
I have an XR10 and I need to change engines and I don't know which one to decide on, this option would be ideal.
Thank you so much for posting this! I have the exact same truck and exact same electronics, except I’m using the Fly sky, noble nb4. I just had a question are you running the front motor let’s say in the throttle slot and the second motor wire into the auxiliary slot? And then you were mixing those two channels? Thanks in advance.
Thanks for this video :) I just picked up a Bully2 and a couple of fusion 2300s. Very timely I found your channel/video :)
I’m planning on using a Holmes svh500lp for added clearance. Any advice on the best way to power it up. I’d hate to hurt anything, any help is appreciated.
Thanks again :)
Bad ass
Care to show or a short video on how you connect both system into the rx
Hi do you have any recommended esc settings for the forward/reverse and braking? I got these motors for my moa
Cool it's similar to the futaba 4pls
Tyler could you show this on a DX5 pro front and rear dig.
Maybe you can help Sir I just got a dx5c and trying to set the rear stear up on my capra like it is on the rtr tx do you know if it's possible? Just getting into the crawling Hobby I didn't have any issue setting it up on the scx6 honcho but I would really like to be able to point and lock the rears independent from the fronts on the capra like I could on the dx3
Did you unplug the red wire out of 1 receiver tab ?
I've heard some unhook a red wire & others leave both tabs with red wires
If i wanted to use the fusion pro 2300kv will i need to adjust the links out or anything like that? Also will the standard radio gear work with it?
How much clearance on the lower arms is there? Fusions are a good bit longer than stock and its close to the lower arms already.
What size fusions you go with? Wish there was an easy way to stick with 1 batterys
1800kv. You can just wire the esc’s to one plug. Positives together and negatives together into one plug.
Did you pull power lead from each from each Fusion and use an external BEC?
Hi tried also to build up with 2 Fusion pro 2300 kv but the front Motor does not really fit with the right Link. Have you adjust the links ?
Is it possible to run a front and rear steer in this? Put a steer axle in the rear
Hi Tyler
would this set-up be possible with a single battery or are dual batterys needed?
Thanks
You can wire it for a single battery.
What channels does it plug into the receiver?
What if I wanna lock the front? An push with the back. It happens can this be done with your mixing?
What the make of the battery's and what the cell size?
Which receiver did you use?
I would like to see you set that up with four wheel steering and be able to steer the front and the rear independently from one another. Is it possible to do that with the radio that you are using?
The remote does have a 4ws function and you can do what you described. I won’t be doing that with this truck as it is for comps and rear steer is not allowed
What is the wieght of the rig?
what motors are those?
Nice! Is it possible to have front and rear dig setup on a dx5c?
I was going to ask the same question. Looks like he isn’t answering any questions though. The video is basically a wast of time. It actually creates more questions than it answers.
You have to create a new mix and reverse the master ant the slave.
@@nick22611 more just showing its possible not so much a tutorial
bro, are the wheels 25mm or 35mm?
How about two hobby wing brush esc
Dont see why not.
Did the fusions fit straight in or did you have to fit new / adapt existing bars ? Tia
My Fusions won't fit with the existing links...
@@DESOUSAB the fusion 2300 is slightly smaller mate. All I had to do was bend the links on one side to accommodate then wind out the coupler slightly to make up the difference
@@lowrevsrc Thanks for sharing the details on how to fit the 2300. How does it drive in bully?
@@KlimovIlya to be fair it’s a lot more controlled but has that punch power when rock hopping
Can you please show us an in depth video of how you made those HW Fusion motors fit? I am looking at close to $500 worth of HW Fusions on my worktop, and they DO NOT fit properly, contrary to what your video shows...
I coud shou you some picture how I make it too fit. If you want.
@@Twin_Hammers That would be great. Just working on setting up the alternative Revolver 540 V3/Mamba Micro X set. Originally grabbed BR Dual for that set up not realizing it was only for brushed motors, and the Revolvers are brushless - doh! If I could get the Fusions to fit, that would be my first choice, though...
@@DESOUSAB Could you give me a few more days? i'm on vacation right now.
@@Twin_Hammers Hey - touching back with you regarding fitting the Fusion motors in the Bully II. I can't get the links to clear the end of the motor...
@@DESOUSAB OMG, I'm so sorry. Coud you give me your e-mail, than I coud send you pictures. And sorry again.
What receiver did you use?