The exterior design of this washer just brought back so many memories. As a kid I would put my wwf action figures on top of the washer lid and I would bang the side of the washer to simulate the pyrotechnic sounds. Good times at the launder mat, haha.
@@baobaolovelyAny washer will do that when the legs aren’t level on it. Make sure the legs are level to the floor,and you’ll be good. You didn’t see the one in the video shaking did you? The legs are level.
Thanks. I love this washer. I'd love to hear the drum roll when you start out soft then get loud with the drum roll on the washer with both hands in a long recording. It's very cool.
The newer models of the speed queen commercial washers doesn't clean anything compared to the older ones. The old washer and dryers in my apartment were recently replaced with these newer models even if there were nothing wrong with them. The newer models agitates so lightly that they don't clean anything even in the heaviest setting while the old washer agitates aggressively, and you can tell it's cleaning your laundry because it shakes the machine while doing it! Might have to start going to the laundromat for this reason, unfortunately.
I agree. I hate the TR series. The only machine they make that u still like is the TC5. It's this washer exactly. Not the new trashy drivetrain that doesn't clean worth anything.
I miss when the laundrymat I used to go to had those while in operation, closed down after a few rebrandings of the convenience store/gas station it was part of.
Washcomats front loads that the laundromat s use are the best Speed queen top loaders are the best top loaders around because they have the commercial grade tubs
Never in my life have I ever heard a speed queen sound THIS BAD during agitation, at somepoint it sounds like the motor needs replacing but other than that it’s a good washer!
How do you get it to work with the lid up? My brand new TC 5000 won’t operate with the lid up and I don’t see anything in the sparsely written instructions about it.
I Have lots of laundromats having these speed queen washer especially the vintage ones! I have a laundromat that’s 2 minutes away from my place and has these washers
how did you take the coin box out i dont even know how too i always wanted a commercial washer dryer but without the coin box or removing the coinbox please tell me and also please tell me how you bypassed the lid switch
Mainly ECON-O-WASH have a blue logo on them but this one has a red, but they are also made by the same manufacturers For Speed Queen And Huebsch i’ve seen a lot of those top loaders at laundromats
I remember I used to see these all the time at a laundromat on the north side of Vegas and I stopped seeing things a back in 2013 and wonder what happened to them.
They're still made, just under the name speed queen now or huebsch and I believe they're all computer controlled now. Still the same machine internally. Any top load huebsch or speed queen is the same as this one.
@@biggysmoovemusic7777 the motor and transmission are the same. The drain pump is the same as well as all the drivetrain. It's just the controls that have changed.
@@nhrawashervideos6567 wow after all these years the design is still the same. That’s truly amazing!!! I wish the Whirlpool and Kenmore direct drives were like that.
I ve seen these in laundromats. They are medicore. Plastic pumps are a big weak point. They also don't handle overloading very well. Nothing really to take pressure off of the belt to keep it from getting glazed when that happens. Also the water level pressure switch is prone to failure as well. Dont believe all the hype about them. In laundromats they need alot of attention.
I HAVE THIS WASHER AT HOME!!! And I absolutely love it! It cleans well, and lasts forever, because we hated our last washer from 4 years ago, it didint wash properly, the agitator is useless, and fake
Assuming the one you had 4 years ago was a Maytag/Whirlpool? They make “Agipellers” (an agitator and FLAT impeller mixed) they don’t do the best with cleaning performance. I have seen worse though. *cough cough Samsung*
@@washingandmowing15 Oh, Yeah you’re right, you should just return it back, My uncle had an older samsung exactly like yours but it sucked, so that’s why I say samsung makes stupid washers
That loud Spin noise reminds me of front loaders, which make the sound of jet airplanes flying and landing while ending cycle. Too bad that Rinse cycle doesn’t last very long.
@@nhrawashervideos6567 I love the aggressive agitation! It sounds like somebody walking during agitation with all that splashing. I didn't know you were 15. I assume you are in high school?
@@nhrawashervideos6567I'd love to hear the finger rolling/tapping on your other machines you have with both hands like a drum roll in a long recording. Nice, smooth, fast and ling.
It's located at the back right. There's actually a trick, the top hangs off the machine in the back about 2 inches. If you get a thick piece of Styrofoam or something similar and wedge it against the lid switch arm when the lid is closed it holds it in the closed position and tricks the machine into thinking it's closed
Hopefully u decide to repair this washer and not scrap it. Their is plenty of vids out their on how to fix these washers, it would be a shame to see this get trashed
@@mikeschulte4271 I unfortunately did end up scrapping it. It was way too far gone. I did save several parts however. Speed queen still makes these in the model TC5
@@tvtimetravel this machine didn't have a low speed, the permanent press or delicate only changed the Wash temp. I'm unsure of the spin speed in low speed.
One of my local laundromats has around like 10 of these washers still going and they're magnificent at cleaning clothes!
This machine here is going to work! I'm certain those clothes are clean!
As I was listening to the washer I'm amazed by the sound. It reminds me of an electric guitar 🎸 One of my favorite washer videos thus far 👍👍
The exterior design of this washer just brought back so many memories. As a kid I would put my wwf action figures on top of the washer lid and I would bang the side of the washer to simulate the pyrotechnic sounds. Good times at the launder mat, haha.
Speed Queen is one of the best top load washers ever manufactured...they literally last forever.
They vibrate on spin cycle and shaking the floor badly and I bought it 7 years ago.
@@baobaolovelyAny washer will do that when the legs aren’t level on it. Make sure the legs are level to the floor,and you’ll be good. You didn’t see the one in the video shaking did you? The legs are level.
@@jamesorsby7553yeah but if it was a Maytag commercial, people would say its junk throw it away
Well the one in my apartment sucks it doesn't even load the coins ugh
You and my sister are the only ones in the world I know that like to tap and drumroll the cabinet before starting a wash cycle.
Thanks. I love this washer. I'd love to hear the drum roll when you start out soft then get loud with the drum roll on the washer with both hands in a long recording. It's very cool.
The newer models of the speed queen commercial washers doesn't clean anything compared to the older ones. The old washer and dryers in my apartment were recently replaced with these newer models even if there were nothing wrong with them. The newer models agitates so lightly that they don't clean anything even in the heaviest setting while the old washer agitates aggressively, and you can tell it's cleaning your laundry because it shakes the machine while doing it! Might have to start going to the laundromat for this reason, unfortunately.
I agree. I hate the TR series. The only machine they make that u still like is the TC5. It's this washer exactly. Not the new trashy drivetrain that doesn't clean worth anything.
I miss when the laundrymat I used to go to had those while in operation, closed down after a few rebrandings of the convenience store/gas station it was part of.
I love watching washers in action. Speed Queen is the best in my opinion. front load and top load.
Washcomats front loads that the laundromat s use are the best
Speed queen top loaders are the best top loaders around because they have the commercial grade tubs
Never in my life have I ever heard a speed queen sound THIS BAD during agitation, at somepoint it sounds like the motor needs replacing but other than that it’s a good washer!
Holy crap is this ever one loud old damn washer
How do you get it to work with the lid up? My brand new TC 5000 won’t operate with the lid up and I don’t see anything in the sparsely written instructions about it.
Just stick something in the back under the control panel between the contact's like a sock
Kinda sounds like the bearings are going out on that washer.
Basically, both the Intermittent Spin & the Final Spin were a spin & drain at the same time.
I Have lots of laundromats having these speed queen washer especially the vintage ones! I have a laundromat that’s 2 minutes away from my place and has these washers
the bearings need to be replaced since the machine makes what sounds like a roaring sound when spinning fast
how did you take the coin box out i dont even know how too i always wanted a commercial washer dryer but without the coin box or removing the coinbox please tell me and also please tell me how you bypassed the lid switch
it didn't come with a coin box, also for speed queens, hang something sorta heavy off the lid switch in the back. you'll see it back there
❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
I do not understand the tapping on the cabinet, what is the point?
A viewer requested I do so, I believe it's something in the world of ASMR
It’s definitely got bad bearings! However, they are easy to replace on these simple washers!
2 Years Later, The bearings are worsening out. That is why
That’s An ECON - O - WASH Top Loader But they were potentially made by the same manufacturers for Speed Queen/Huebsch
Its just a speed queen w/ different sticker. This one needs work
Mainly ECON-O-WASH have a blue logo on them but this one has a red, but they are also made by the same manufacturers For Speed Queen And Huebsch i’ve seen a lot of those top loaders at laundromats
Nice video, I will be filming one today. Just aks8ing how did you bypass the lid switch?
I remember I used to see these all the time at a laundromat on the north side of Vegas and I stopped seeing things a back in 2013 and wonder what happened to them.
They're still made, just under the name speed queen now or huebsch and I believe they're all computer controlled now. Still the same machine internally. Any top load huebsch or speed queen is the same as this one.
@@nhrawashervideos6567 ohhhhhhh ok. Do they still have the same exact design?
@@biggysmoovemusic7777 the motor and transmission are the same. The drain pump is the same as well as all the drivetrain. It's just the controls that have changed.
@@nhrawashervideos6567 wow after all these years the design is still the same. That’s truly amazing!!! I wish the Whirlpool and Kenmore direct drives were like that.
Is the bearing bad or is that just a really loud motor?.
It sounds like a bad bearing to me as when it stopped it still made the sound.
Also mind if you film this washer but just in whites in warm water?
Don't have this one anymore. Sorry!
Oh ok! What happened to it?
anything could've happened to it
Where do we put the softener?
This one doesn't have a dispenser. You'd have to manually add it to the Rinse water.
You can keep the lid up on wash cycle is that correct?
I can since I defeated the safety switch.
02:26 Wash
12:21 Rinse
19:48 Spin
25:52 End
Nice washer.
question is it that loud or is it just the microphone or is it just me
I ve seen these in laundromats. They are medicore. Plastic pumps are a big weak point. They also don't handle overloading very well. Nothing really to take pressure off of the belt to keep it from getting glazed when that happens. Also the water level pressure switch is prone to failure as well. Dont believe all the hype about them. In laundromats they need alot of attention.
Thank you at least someone said it people who love speed queen is not going to admit the washer has issues
I HAVE THIS WASHER AT HOME!!! And I absolutely love it! It cleans well, and lasts forever, because we hated our last washer from 4 years ago, it didint wash properly, the agitator is useless, and fake
Assuming the one you had 4 years ago was a Maytag/Whirlpool? They make “Agipellers” (an agitator and FLAT impeller mixed) they don’t do the best with cleaning performance. I have seen worse though. *cough cough Samsung*
@@washingandmowing15 What was with the *”Cough cough Samsung”* Was it just like a joke or something?
@@universaldrummer007 no, emphasizing how sucky Samsung is. I have had bad experiences all around with them and I’m sick of them.
@@washingandmowing15 Oh, Yeah you’re right, you should just return it back, My uncle had an older samsung exactly like yours but it sucked, so that’s why I say samsung makes stupid washers
Its weird on how it fills…
It needs parts replaced. but driver to she won't go no more. It is worth rebuilding.
That loud Spin noise reminds me of front loaders, which make the sound
of jet airplanes flying and landing
while ending cycle. Too bad that Rinse cycle doesn’t last very long.
Yeah the spin noise is due to failed drum bearings. Years of use in a laundromat put major strain on them and they gave out recently
@@nhrawashervideos6567 I love the aggressive agitation! It sounds like somebody walking during agitation with all that splashing. I didn't know you were 15. I assume you are in high school?
@@nhrawashervideos6567I'd love to hear the finger rolling/tapping on your other machines you have with both hands like a drum roll in a long recording. Nice, smooth, fast and ling.
@@jeromedavis8575 that I would be indeed!
@@nhrawashervideos6567 What are your favorite activities outside of work?
seems to fill slightly less water than needed
That motor sounds horrible and the bearings sound pretty bad too so this machine will need some servicing. Probably around 15-25 years old .
Where in the machine is the lid switch located? How did you rig it for it operate with an open lid?
It's located at the back right. There's actually a trick, the top hangs off the machine in the back about 2 inches. If you get a thick piece of Styrofoam or something similar and wedge it against the lid switch arm when the lid is closed it holds it in the closed position and tricks the machine into thinking it's closed
That motor sounds like SHE DONE lmao
its actually a relatively new motor! installed in 2016. I believe its a capacitor or transmission issue.
@@nhrawashervideos6567 gotcha just sounded vibraty loud like when the motors get real old and worn out
Hopefully u decide to repair this washer and not scrap it. Their is plenty of vids out their on how to fix these washers, it would be a shame to see this get trashed
@@mikeschulte4271 Totally agree he should. Very very good heavy duty washer, a classic you’d never get from today’s market!
@@mikeschulte4271 I unfortunately did end up scrapping it. It was way too far gone. I did save several parts however. Speed queen still makes these in the model TC5
Why is it so noisy.😮
It sounds like 700 Rpm.
What is NHRA VIDEOS
Just happens to be the name I picked.
those bearings were not happy lol
What is s the rpm for final spin?
710
@@nhrawashervideos6567 What about low speed in the Delicate and Permanent Press cycles?
@@tvtimetravel this machine didn't have a low speed, the permanent press or delicate only changed the Wash temp. I'm unsure of the spin speed in low speed.
Muy ruidosa