Yes, this was helpful. Because it's only me and I don't wash much, knowing how to increase the temperature was helpful. I usually wash every load on WHITES so the water is hot enough. I also use Earth Breeze laundry soap and tear one sheet in half and put it on top of the soiled clothes, rather than put it in the dispenser.
Hey Brenda. Lint in the vent ??? I can't say for sure - but I am guessing the vent is clogged and therefore the moisture cannot be carried out of the dryer. Have you confirmed that the vent is clear?
@@EarlAndJill I ran the cleaning cycle and a lot more lint was in the tub. Then pulled off the panel to the area behind closet to inspect the hose. The hose had a puddle of water inside of it where it drops down. I unhooked the hose from the back of machine and was able to drain the water into a bucket. I reconnected the hose and ran a dryer cycle. I hope by doing the monthly cleaning cycle this will solve the water in hose problem. I will up date.
@@MsBsPlace I agree with running the ceaning cycle - But water - in a puddle - in the VENT hose? that has me curious. Did rain perhaps enter from outside? Just Curious.
Love it very much already but no one shows how to just dry a load that is still wet. Been trying every thing and it goes back to full cycle to wash. Also, our dial is out of alignment and points between to points. Hope you can help
Hey Brad! ... I am traveling at the moment - as soon as I get back I'll make a quick vid on the drying part. On the alignment - I'll have to investigate ! Take care.
Hey, thanks for the quick reply. I figured out that the settings dial was completely off. It must have been popped off while being installed. I took it off and it wasn't even placed according to the notch. It was 180 degrees off. Now the settings make sense.
Thanks for that info ... I did some looking ... boy ! The PATH (Whirlpool, Ariston, Hotpoint) sure gets muddied fast. I'm still not "Clear" ha ha. Like ROLLS ROYCE - Some parts (were) Ford, Lucas Truck, and others. NOW ... Combination of VW and BMW - and Lucas - ... Rolls brake pads are expensive. Buy the FORD ESCORT and drill 12mm hole for sensor. SAME material. etc. :)
Yes, this was helpful. Because it's only me and I don't wash much, knowing how to increase the temperature was helpful. I usually wash every load on WHITES so the water is hot enough. I also use Earth Breeze laundry soap and tear one sheet in half and put it on top of the soiled clothes, rather than put it in the dispenser.
Hey Judy ... I am glad this was helpful ... I have never used the fabric sheets in this setup ... Be safe out there ! :)
I have this machine. For two days now it takes longer to dry. I checked the vent outside and the lint in the vent is wet. Can you help?
Hey Brenda. Lint in the vent ??? I can't say for sure - but I am guessing the vent is clogged and therefore the moisture cannot be carried out of the dryer. Have you confirmed that the vent is clear?
@@EarlAndJill I ran the cleaning cycle and a lot more lint was in the tub. Then pulled off the panel to the area behind closet to inspect the hose. The hose had a puddle of water inside of it where it drops down. I unhooked the hose from the back of machine and was able to drain the water into a bucket. I reconnected the hose and ran a dryer cycle. I hope by doing the monthly cleaning cycle this will solve the water in hose problem. I will up date.
@@MsBsPlace I agree with running the ceaning cycle - But water - in a puddle - in the VENT hose? that has me curious. Did rain perhaps enter from outside? Just Curious.
Love it very much already but no one shows how to just dry a load that is still wet. Been trying every thing and it goes back to full cycle to wash. Also, our dial is out of alignment and points between to points. Hope you can help
Hey Brad! ... I am traveling at the moment - as soon as I get back I'll make a quick vid on the drying part. On the alignment - I'll have to investigate ! Take care.
Hey, thanks for the quick reply. I figured out that the settings dial was completely off. It must have been popped off while being installed. I took it off and it wasn't even placed according to the notch. It was 180 degrees off. Now the settings make sense.
these are hotpoints
Thanks for that info ... I did some looking ... boy ! The PATH (Whirlpool, Ariston, Hotpoint) sure gets muddied fast. I'm still not "Clear" ha ha. Like ROLLS ROYCE - Some parts (were) Ford, Lucas Truck, and others. NOW ... Combination of VW and BMW - and Lucas - ... Rolls brake pads are expensive. Buy the FORD ESCORT and drill 12mm hole for sensor. SAME material. etc. :)