@@QuickAndEasy5MinuteAppliance Turns out i could have used the spring removal tool for the outer ring, but I ended up just using two pieces of string to on either side of the spring and pulling it apart to loosen the spring. Also, my model was a bit different, the soap dispenser tray's chute is fashioned into my door boot (which is where the original one teared). After getting the inside of the boot on, i had to wiggle it a lot to get it into the right place under the chute, to avoid more tearage, before fastening the inner ring on.
Very helpful video. Thanks for posting it. A few additional details. When removing the control panel (see 0:57), there's a tab on the right side (in front of where those orange stickers are in this video) that you need to push in to release the panel. The presenter wiggled the panel loose, but it's easier if you release the tab first. Also, at 2:09, you see a tube coming out the front at the bottom of the washer. That's where the filter is on this washer. If you're replacing the door boot, you should absolutely clean the filter at the same time. Get a bowl or other small container to catch the water that will come out when you unscrew the cover. A good bit of water will come out, so if you're using a small bowl or container, you may need to screw the filter back in for a moment while you dump out the container. Take the filter out. Like me when I did this, you'll probably find some coins or other small items that the filter caught. Remove them, then wash the filter and screw it back in. Be sure to tighten it all the way, or it will leak. Finally, at 3:00, the presenter suggests using olive oil or laundry detergent to lubricate the new boot when putting it on. The thing to know about that is, there's a tradeoff. Using a lubricant will make it easier to put the boot on, but it will also make it more likely that it will come loose when putting the metal bands on. I suggest trying to put the boot on without lubricant at first and, if it's too difficult to get it on, use lubricant, but be mindful that it may be harder to keep it in place.
I just got done finishing your video. The instructions were step by step and easy to follow. Thanks. You just saved me from having to buy a new washer.
thanks! going to use this for our He4t, shocks went bad then boot tore, actually fixed boot with patch but bad shocks, so it leaked again 2 months later lol got the shocks need to buy the boot! love this 18 year old machine, best dang washer ever made!! :D
Thanks for a great instructional video. Our boot was moldy and I wanted to clean it really good so I removed it. I couldn’t get it back in so I found your video, removed the panels and it was a lot easier. Thanks!!!!
Thanks very much! Was having a hard time finding a door boot replacement video that matched with our older model Kenmore He2t washer, but this was the one. Easy to follow esp. regarding the various types of tools & screws needed to do the job. Appreciate it!
Thanks for the vid. Got me going in the right direction but wish I would’ve taken the spring clamp on the front panel before I took the front panel off.
Thanks for the straight forward video. I must have missed you removing the outer clip at first. When you reinstalled it at the end I was like aha! But that bugger gave me the most trouble. I am doing a test load of towels now. Also discovered some socks and underwear crammed under the full spout. Which is probably the main cause of the massive water from yesterday’s laundry. But it had leaked periodically before. Thanks again
I got to the 2:28 mark and couldn't figure out why the door wasn't coming off. I had to rewatch a few times before I realized that he didn't show removal of the outer spring and the lip of the boot was already pushed off the door opening.
Thank you for the great video! I was able to change my boot fairly easily and now there are no more leaks! The boot I ordered online from Kenmore went on a lot easier than expected.
Thank you very much -- your video made it an easy process. All went well until I was finished, and now the door won't close. Boot protrudes a bit, but I don't think that's the problem. Any tips would be greatly appreciated!
There's a retaining ring that is spring loaded that holds the outer part of the gasket against the front panel. That should be removed before you lose the front panel.
Great video helped me replace the boot, I disconnected to control cable and not sure how to reconnect. Do you know which cable goes in which connector? Thanks
On older models, you don't need to unscrew anything. Just open the door, pull the thing out and put the new one in (much easier said than done). It helps if you can tilt the machine back. I used 4x4 blocks under the front.
That's a great idea. The loops on the spring clamp on the washer I worked on were pretty small, so I don't know if zip ties would have fit. But your suggestion is absolutely worth a try.
great video except my new spring clamp comes apart when I try to get it back on... Still isn't on. Any other tips to get it back on besides lubricating the wire?
Good idea , should still give you some more years. Since the cost of the boot is pretty cheap, I would just buy a new one and get a lot of years of service👍
Sometimes those new boots stick out a bit and make it hard to lock . Try aiming a hairdryer at the boot for 10 minutes and then close the door and keep it closed with duct tape over night.
thanks for detailed video, saved me having to buy a spring removal tool that i saw on other videos
Glad I could help😊
@@QuickAndEasy5MinuteAppliance Turns out i could have used the spring removal tool for the outer ring, but I ended up just using two pieces of string to on either side of the spring and pulling it apart to loosen the spring.
Also, my model was a bit different, the soap dispenser tray's chute is fashioned into my door boot (which is where the original one teared). After getting the inside of the boot on, i had to wiggle it a lot to get it into the right place under the chute, to avoid more tearage, before fastening the inner ring on.
Very helpful video. Thanks for posting it. A few additional details. When removing the control panel (see 0:57), there's a tab on the right side (in front of where those orange stickers are in this video) that you need to push in to release the panel. The presenter wiggled the panel loose, but it's easier if you release the tab first.
Also, at 2:09, you see a tube coming out the front at the bottom of the washer. That's where the filter is on this washer. If you're replacing the door boot, you should absolutely clean the filter at the same time. Get a bowl or other small container to catch the water that will come out when you unscrew the cover. A good bit of water will come out, so if you're using a small bowl or container, you may need to screw the filter back in for a moment while you dump out the container. Take the filter out. Like me when I did this, you'll probably find some coins or other small items that the filter caught. Remove them, then wash the filter and screw it back in. Be sure to tighten it all the way, or it will leak.
Finally, at 3:00, the presenter suggests using olive oil or laundry detergent to lubricate the new boot when putting it on. The thing to know about that is, there's a tradeoff. Using a lubricant will make it easier to put the boot on, but it will also make it more likely that it will come loose when putting the metal bands on. I suggest trying to put the boot on without lubricant at first and, if it's too difficult to get it on, use lubricant, but be mindful that it may be harder to keep it in place.
I just got done finishing your video. The instructions were step by step and easy to follow. Thanks. You just saved me from having to buy a new washer.
Thanks for posting this tutorial! Man that spring holding outer seal was a bear to get on but with a helping hand I was successful.
Nice job Paul👍
thanks! going to use this for our He4t, shocks went bad then boot tore, actually fixed boot with patch but bad shocks, so it leaked again 2 months later lol got the shocks need to buy the boot! love this 18 year old machine, best dang washer ever made!! :D
Very cool😊
Thanks for the video, a few years later and still a big help.
Best video I watched out of at least 15. Most accurate and easy to follow. Thank you sir.
Thanks so much Craig😊😊😊
Well done, sir. I followed the instructions and had zero issue replacing my Kenmore boot.
Thanks so much Kevin
Thanks for a great instructional video. Our boot was moldy and I wanted to clean it really good so I removed it. I couldn’t get it back in so I found your video, removed the panels and it was a lot easier. Thanks!!!!
Nice job Chris😊😊😊
Thanks very much! Was having a hard time finding a door boot replacement video that matched with our older model Kenmore He2t washer, but this was the one. Easy to follow esp. regarding the various types of tools & screws needed to do the job. Appreciate it!
You’re very welcome 😊
Thanks for the vid. Got me going in the right direction but wish I would’ve taken the spring clamp on the front panel before I took the front panel off.
That’s right 👍
Thank you for this excellent tutorial! My washer is working with no leaks!
Awesome, thanks Phill
Thanks for the straight forward video. I must have missed you removing the outer clip at first. When you reinstalled it at the end I was like aha! But that bugger gave me the most trouble. I am doing a test load of towels now.
Also discovered some socks and underwear crammed under the full spout. Which is probably the main cause of the massive water from yesterday’s laundry. But it had leaked periodically before. Thanks again
Nice job👍
Yeah he didn't post removal of the spring retainer and yes it's a pain to get back on!
I got to the 2:28 mark and couldn't figure out why the door wasn't coming off. I had to rewatch a few times before I realized that he didn't show removal of the outer spring and the lip of the boot was already pushed off the door opening.
Thank you for the great video! I was able to change my boot fairly easily and now there are no more leaks!
The boot I ordered online from Kenmore went on a lot easier than expected.
Thank you very much -- your video made it an easy process. All went well until I was finished, and now the door won't close. Boot protrudes a bit, but I don't think that's the problem. Any tips would be greatly appreciated!
How did you fix it, I’m having the same problem!
There's a retaining ring that is spring loaded that holds the outer part of the gasket against the front panel. That should be removed before you lose the front panel.
That’s right,
Thanks Patrick😊
I’m confused why nobody mentioned that- a whole step missing from the video got me pretty confused. The rest of the video was great.
Thank you very much. You saved me time and money.
Thanks Tony I’m so glad it worked for you😊
Perfect video. Helped so much. Thank you
Glad it helped!😊
Thank you. Straight forward explanations and it all came out well.
Excellent,
Thank you
thank you for the video. this is great help for me replace kenmore H2 plus door boot.
Glad it helped Paul😊👍
Great video helped me replace the boot, I disconnected to control cable and not sure how to reconnect. Do you know which cable goes in which connector? Thanks
How did you tighten the spring clamp?
On older models, you don't need to unscrew anything. Just open the door, pull the thing out and put the new one in (much easier said than done). It helps if you can tilt the machine back. I used 4x4 blocks under the front.
You’re right.
It’s tricky but it can be done.
It's a great day to be a live
You are so right😊😊😊
Thank you so much Very nice of you to do the video
Thanks Nancy😊
Tip: if you have a spring clamp that needs to be spread just slide a zip tie in each side make a loop and pull apart.
That's a great idea. The loops on the spring clamp on the washer I worked on were pretty small, so I don't know if zip ties would have fit. But your suggestion is absolutely worth a try.
A pair of snap ring pliers should work too. 5 bucks at harbor freight. Very useful to have around
great video except my new spring clamp comes apart when I try to get it back on... Still isn't on. Any other tips to get it back on besides lubricating the wire?
Might want to get a second set of hands to help you.
Should mention to clean the pump strainer while you have the bottom cover off
Thanks
No problem😊👍
Thanks for you video that help me a lot.
But I don't know the door don't want lock
Try pushing in on the door as it starts to help it lock.
@@QuickAndEasy5MinuteAppliance ok perfect thank you
Is there something that can seal the tear in my rubber boot?
I’ve used a bike inter tube repair kit.
@@QuickAndEasy5MinuteAppliance Thank you,
Is it alright to clean the Old boot and put it back on or is it better to get a new one?
Good idea , should still give you some more years.
Since the cost of the boot is pretty cheap, I would just buy a new one and get a lot of years of service👍
@@QuickAndEasy5MinuteAppliance the one I bought was 165.00 for the boot and new clamp
Great video!!
Glad you enjoyed it
Does this procedure also applies for the Kenmore HE²plus..?
Nice watch!
Thanks Andrew👍
great video. thank you for your help
Did all that but now my door will not lock. Any thoughts?
Sometimes those new boots stick out a bit and make it hard to lock .
Try aiming a hairdryer at the boot for 10 minutes and then close the door and keep it closed with duct tape over night.
@@QuickAndEasy5MinuteAppliance I’m gonna try that
What would cause a front load Kenmore to leak through bottom of unit
Could be a dirty glass door where it meets the rubber door boot.
Very helpful thanks
You’re welcome
Scott, does this door boot fit a Maytag 2000 front loader?
The front did not come off easy. The boot is attached to the front panel!!!!
On some brands, they glue the boot to the front panel in 4 small places. It’s mainly the Fridgidaire Gallery washer
Nice voice for narration, but jerky movements made the video very difficult to watch, ruining an otherwise excellent video.
Sorry to hear that
Thanks, very helpful!
You’re very welcome 😊