Just about to do this repair on a Fiat Scudo. Thanks for the guide. Often the reason the roller wears out is from greasing the track. It may appear to make it slide easier, but the grease also attracts abrasive grime which ultimately causes the roller to seize up. Then it wears a flat spot, the rubber wears through and the steel wheel starts cutting a groove in the track. This is the mistake I made! I'd suggest that the best thing to do is to simply always clean and dry the track when washing the vehicle. If the track is clean but the rollers are stiffening up, I've seen it suggested that a small squirt of silicon spray directly on the roller bearing will help, but also to wipe off any excess silicon immediately. Try not to leave anything left on the track surface and outside of the roller to which grit and grime sticks.
Hi Dee, i'm absolutely sure that this is what happened to our wheel and rail. I totally agree that you should keep it clean. Good luck with your repair.
Hi Mick, thank you for your positive response! I just checked the roof rack, but there is no brand sticker on it. The roof rack was already installed when I bought the van.
J'aurais bien aimé le faire aussi, mais les vis du rail n'étaient plus accessibles. Du moins pas sans casser beaucoup. J'espère que vous avez obtenu le résultat que vous espériez :)
Hi Pandy, in the description you will find this link bit.ly/3fTADwS . On the website of autodoc you can choose the brand, type , etc. of your van. I'm sure you will find the part number. Good luck!
Is it possible to just replace the roller? Because it’s uncommon to have driver side (UK right hand drive) sliding door, so the ‘rip-off’ e-bay seller wants £25 for the hinge and £50 for postage. But you can buy top, middle and bottom hinge for the passenger side for £25 free postage.
Hi @clankyrochet, if you follow the link in the description, you will arrive at autodoc. They have the part for the right as well as the left sliding door. I believe even single rollers, but I didn't find it convenient to just replace the roller.
Too be honest...I'm not quite sure. Mine is a little out at the bottom. I tried adjusting the bolds at the bottom, but was not yet successful. So I'm looking into it. Will let you know if I find the solution. Hope you will do the same ;-)
hi I have problem with leaking sliding door on 2014 Renault master ... I have changed rubber seal and have adjusted top hanger + door catch .. but still leaks from top back of door... would changing the roller guide lift the door for a better seal ??? thanks for any info
Wow what an excellent video, perfect explanation! Thank you so much!
Thanks for the appreciation, @jimonfoot! Hope that you fixed your van :)
Excellent video just the job nice and easy to follow perfect.👍
Thank you, Steve! It is made and shared with pleasure :-)
Thank you
With pleasure!
Thanks a lot for that. Good job. I now know what to do, Cheers
With pleasure, Dave!
Great video...mine needs doing so i assumed it meant removing whole door..great
Hi @singtracks, thanks for the appreciation. Good luck with the replacement! :)
Gracias por tu video.
¡Eres bienvenido!
Great video, very helpful 👍
with pleasure!
Thank you for video, i have to do it as well in my van 🤝
Thank you, Sebastian. Succes with replaceing your roller guide.
Thanks great video
thanks!
Tankes
Glad that I could be of help! Take care, Amanti :)
Great video thank you, I need to do mine.
With pleasure, robert!
Thank you so much!!
my pleasure
Just about to do this repair on a Fiat Scudo. Thanks for the guide.
Often the reason the roller wears out is from greasing the track. It may appear to make it slide easier, but the grease also attracts abrasive grime which ultimately causes the roller to seize up. Then it wears a flat spot, the rubber wears through and the steel wheel starts cutting a groove in the track. This is the mistake I made!
I'd suggest that the best thing to do is to simply always clean and dry the track when washing the vehicle. If the track is clean but the rollers are stiffening up, I've seen it suggested that a small squirt of silicon spray directly on the roller bearing will help, but also to wipe off any excess silicon immediately. Try not to leave anything left on the track surface and outside of the roller to which grit and grime sticks.
Hi Dee, i'm absolutely sure that this is what happened to our wheel and rail. I totally agree that you should keep it clean. Good luck with your repair.
actually wd 40 i have found to be better
Thanks that helped me, can I ask what make roof rack is that?
Hi Mick, thank you for your positive response! I just checked the roof rack, but there is no brand sticker on it. The roof rack was already installed when I bought the van.
Too video
Thank you :-)
Il fallait changer le rail aussi pour bien faire...
J'aurais bien aimé le faire aussi, mais les vis du rail n'étaient plus accessibles. Du moins pas sans casser beaucoup. J'espère que vous avez obtenu le résultat que vous espériez :)
@@vanred_nl c'est dommage car les roulements vont s'abîmer à nouveau .
Grat video - does that help in the door being slightly misaligned? Mine (Renault Master Mk3) is about 5mm lower than it should be!
Hi andrew, do you want to know if changing the roller guide fixes the door being misaligned?
@@vanred_nl yes please!
Jak wymienic lewarek zmiany biegow . Czy jest może film
Unfortunately, I can't help you with that. Good luck with the search!
Thanks so much!!! Would you say there was a difference in function after sanding the rail??
Definitely! Besides that, the grooves would have damaged the new wheel over a short time of period.
@@vanred_nl My door literally fell off when closing it. Ordered new rail and runners now. Thanks for this video again so helpful
I have a 2014 Renault Master with sliding door on left side as in Australia. Can you provide correct part number or where I can obtain part?
Hi Pandy, in the description you will find this link bit.ly/3fTADwS . On the website of autodoc you can choose the brand, type , etc. of your van. I'm sure you will find the part number. Good luck!
Ciszko wchodzi bieg 1i wsteczny, linki Ok są pytanko czy to lewarek ?
We have no experience with the engine or drive. The van has always been taken to a garage for maintenance. I hope you find an answer to your question.
Jak wyregulować dzwi przednie mowano b
Jak wyregulować drzwi wejściowe Movano B? Brak pomysłu. Niestety nie mogę Ci pomóc. Mam nadzieję, że wkrótce znajdziesz rozwiązanie. Powodzenia!
Is it possible to just replace the roller? Because it’s uncommon to have driver side (UK right hand drive) sliding door, so the ‘rip-off’ e-bay seller wants £25 for the hinge and £50 for postage. But you can buy top, middle and bottom hinge for the passenger side for £25 free postage.
Hi @clankyrochet, if you follow the link in the description, you will arrive at autodoc. They have the part for the right as well as the left sliding door. I believe even single rollers, but I didn't find it convenient to just replace the roller.
Keep in mind that, after Brexit, it actually costs extra money to import/export products to and from the UK :S
hi my master mk3 sliding door is out a little to far at the top and needs to go in a bit. how would i fix this what bolds?
Too be honest...I'm not quite sure. Mine is a little out at the bottom. I tried adjusting the bolds at the bottom, but was not yet successful. So I'm looking into it. Will let you know if I find the solution. Hope you will do the same ;-)
@@vanred_nl ok cheers be trying again over the weekend
A jak zdemontować prowadnic szyby
Nie rozumiem twojego pytania, przepraszam.
Prowadnica lewej szyby jak wymienic opel mowano 2011r
hi I have problem with leaking sliding door on 2014 Renault master ... I have changed rubber seal and have adjusted top hanger + door catch .. but still leaks from top back of door... would changing the roller guide lift the door for a better seal ??? thanks for any info
I don't know if that will fix the problem, Lucky Strikes. How is the rail of the sliding door? Is it straight?
Ciszko chodzą boczne dzwi co poprawidz
Cześć, niestety nie mogę Ci w tej sprawie więcej pomóc. Mam nadzieję, że ktoś inny zna odpowiedź na Twoje pytanie. Powodzenia!