Thank god!!! Every time iv seen an American do a review or a video like this they've gone "and this is the box, and this is the packaging" and spent like 5 minutes on bs. You just go, "chuck that" LEGENDDDDDD!!!!!!! Totally cool guy!
Aftermarket speakers are better with an aftermarket amp. Unless your car is higher end and stock factory stereo is higher wattage output. If it's not, then you loose quite a bit of bass vs factory speakers
Very true about the wattage, but when it comes to replacing door speakers for aftermarket upgrades, you’re pretty much always going to lose bass regardless of it being amplified due to crossovers. Hence why we all install subwoofers to properly set the sound stage and bring those nice low frequencies back. And don’t forget the tweeters for the highs!
@@ETG311 what? Plenty of my cars I’ve only installed good stereos and speakers and never felt like I needed a subwoofer unless I wanted absurd bass. I know this is an old comment but the bass that you “lose” is going to hardly make a difference, at least not enough for you to want to go spend 500+ minimum on a sub
Thank you for the explanation of speaker size at the beginning. Cleared up most of my questions about doing an install in the first 2 minutes of the video
I love these speakers 🔊 I have two inside a dual box in my middle console of my truck. They sound super crisp and clean and zero distortion at max volume
why would you not show us you clamping the red pieces together and how to cut them and put them in?!?! that's how you connect it and you don't show it??
Joshua Sarno Mainly because there are various methods of connecting two wires together. Soldering, Crimping (like in the video), and twisting the wires together are just a few options. Considering there are so many ways, we will make another video on how to securely and safely make electrical connections. And to answer your question, we didn't include that in the video for sake of time. Thank you for your feedback!
CalebsAutoHelp a bro my 01 Buick regal has stock tweets and I want to replace them. Do I cut there wire to the stock one and wire the plug in part to the new tweets plug back in and it good to go or what? I'm lost af
This was the best video of changing speakers I have seen mostly based on the fact your explained all the different ways of connecting instead of going HA YOU HAVE TO CHOP YOUR WIRES UP
Hello, i have installed an aftermarket pioneer stereo (deh- s320bt) in my car which says "output power: 50 (*4) watts" . Until how many watts RMS speakers can i buy? Cause i dont know if this "50" is watt RMS. For example if i place 80 Watt RMS speakers in my car, will the stereo be burnt? I have found some speakers (Jbl stage2 604c) which are 45 watt RMS and 270 watt max power . Will they fit my car?
with some car audio speakers they require a 4way amplifier (not a subwoofer amp) the actual car speakers. i would love to see a video on how to install that
hey i got a question....i have a chevy cruze 2014 iam trying to install 6x9 in the rear deck. but my car came with no speakers or wires in the rear. but the hole is there but the actual carpet panel doesnt have the holes. do i have to cut out the holes so the speakers can go through or just leave it the ay it is and just install the speakers?
I'm a real noob when it comes to this and I have a question. Are the wiers on all speakers the same ? I have an old car with crap speakers hooked up to a radio. Can I install new speakers with the same wier from the old speakers ? or will I have to get new wiers.
I have a speaker that comes with built-in lights. Where should I connect its positive terminal so that the speaker lights turn on when I switch on my vehicle lights? Also where should I connect the ground wire? Pls help
Double check and see if the packaging for your speakers note what voltage the lights require. If it's 12v, you would need to run a wire from the speaker to another wire that turns on when the vehicle turns on, or to a fuse box where you could tap into a circuit using a fuse tap. The fuse tap option might be easier if you don't have a multimeter to probe wires with. You'd just pull out a fuse for something that turns on when your vehicle does, insert the fuse tap in its place, insert the original fuse into the bottom slot of the fuse tap, insert a new fuse in the top slot to protect your lights, then connect the positive light wire to the fuse tap. As for the ground, find a bolt or nut that screws directly into metal that is relatively near your speaker (you might even find one with wires attached already, that is a grounding point), put a ring terminal on your wire, unscrew the nut or bolt, attach ring terminal, and screw back down. The entire metal chassis of your vehicle is connected to the negative post of your battery, this is why you might come across a bolt with wires connected to it like I mentioned previously. One last thing. If the packaging states that the required voltage for the lights is less than 12v, you're going to need a resistor on the positive wire going to the lights to drop the voltage down. I would assume they are 12v, but if not you can use a resistor calculator online to find what value resistor you'd need. Sorry for the wall of text, but I hope this helps. Sincerely, the guy from this video.
I need help guys and this video was awesome. I just got a 2006 chevy tahoe. I installed some 300w Pioneer speakers in front now i need back door speakers. My buddy gave me a pair of 6x9 and it says the back is 5x3/4 how do i mount them?
If I wanted to to add a Center Dash channel to a stock 4-channel radio, is it OK to use the left front positive lead, and the right front negative lead with an 8 ohm L-pad to create a center dash mono channel?
That would be a waste. Most if not all sub woofers require an amp to get the kind of power necessary to the speakers. Also sub woofers are highly specialized in the sound they deliver. Car speakers can deliver highs mids and low sounds where as the sub woofer is only lows. Your car would only be able to make the sound of a microwave really. Vocals could no longer be heard but the drums will sound fantastic.
Manjunath wtf no. Speakers work by using electromagnetism to create a magnetic field that oscillates the membrane and creates vibration, ultimately vibrating the air around it and making sound.
Joe Barbaro with car door speakers it doesnt matter which one is positive and which is negative just connect the wires to either one. In this guys case its super easy because all you have to do is match small with small and big with big
You need to add a spacer in between the speaker and where it mounts. If you google the make and model of your vehicle along with "speaker spacer" you might be able to find pre-fabricated ABS spacers specific to the speaker holes of your vehicle. Maybe also check the Metraonline.com vehicle fit guide and see if they have anything for your car. If you can't find them for some reason, you might need to make some with some MDF or ABS, or if you don't have tools you can probably find a car audio shop to make some for you.
I'm planning on replacing my stock door speakers on my 2014 Nissan Sentra but I'm hearing some debate about 2 way and 3 way speakers. Some say 3 way speakers aren't any better that 2 way speakers. In fact they say it's worse because the tweeters restrict vibrations of the woofer. In your opinion which is better ? I'm looking for power and clarity.
Doamino41 In case of 3 way you hear a good combination of good bass and voice clarity. there no such thing like tweeters do affect bass or etc.. :) In case of 2 way you hear more bass but a limited voice clarity. Make sure to already select a good speaker!
Doamino41 did you install aftermarket speakers with the stock radio ? If you did were there any changes in audio cause there's some things going around talking about how they would sound shitty if you use the stock radio with aftermarket speakers.
Actually I did replace all my speakers with Pioneers. 6 by 9s in the back and 6 1/2 in the doors. What a pain in the ass! Now it sounds louder but not clearer. That means I will need an after market double din radio with a SWC adapter. Some sources suggest an amplifier also. But yes you are right. Better speakers with the same crappy stereo won't sound much better.
I'm pretty sure I can just use new speaker wire that has a positive and negative and just twist then clamp them onto the original wires of the car? Isn't that all that you actually bought ?just positive and negative wires cut the clip off then crimp it? I'm sorry I'm just about to do this to my car and was wondering thanks! Great video btw .
Love Sucks correct! The new speakers will come with a wiring harness in the box, normally with pressure fit connections pre installed (like in the video). If they don't, you can easily attach your own speaker wire between the speaker and speaker wiring from your car, either by using crimp connectors, or soldering. Best of luck with your install! Let us know if you have any further questions.
Could you help me to make decision for my car audio upgradation? I dont want a sub. Cs 6.5 front & Ks 6x9 3way rear, do this combination make good bass? do revert pls :)
Colton Sailor Absolutely. The main reason we installed the Kickers is so that we can install an amp in the future, to more adequately power them. They still sound great without an aftermarket amp, they just lack volume.
Anyone recommend some good speakers for my 2011 Lincoln town car ? My stock ones are starting to go bad. I want some with some good sound a lil bass bump too. I used to have the sub and amp I’m the trunk but maybe I’m over that
wow he's a cute guy I love the way uses his hands tell us every little detail man in the detail not to not details tell us all the little details tell us the story
I might have the easiest solution Just by 2 or 3 jbl speakers and put them in the door cup holders Put charge cables in and they won't go empty. Connect them. And you got sound from left and right. Ez to do and you only have to turn them on. Connect them with 1 press use your Phone for Bluetooth. And done. Now you got great quality sound in your car after 2 minuts Maybe not the loudest but hey, your'e just ruïning your ears if you turn the volume all the way up
This was literally just a video that covered common sense. The “specifics” that everyone was trying to find, got cut out (technical difficulties), while you were probably; blowing fuses, taping your own finger to a wire, and possibly mistook your own shadow for a burglar, causing you to have a liberal fuel anxiety attack. Now the actual information displayed on this video, consisted of how to take a door panel off a car (which has never been an issue, for any DIY’er, EVER), and an extremely drawn out tutorial on plugging in “the big one to the big one” and “small one to small one”. If you thought this video was in any way beneficial, y’all deserve each other. 👍🏼
I’m sorry that you feel that way about the content in this video. We posted it with the intent of teaching anyone how to upgrade their speakers, because not everyone knows how to. Additionally, saying that taking a door panel off a car has never been an issue for a “DIY’er” is quite far fetched. Most people have never removed a door panel, and now because of this video 200,000+ people have that knowledge. Thank you for your feedback.
![САНАТОРИЙ для беглых ДИКТАТОРОВ. Асада подселили к Януковичу 😁 [Пародия]](http://i.ytimg.com/vi/vI6jO-XmAY0/mqdefault.jpg)
Dude, super helpful. Every other video failed to take you through the actual connecting of the wiring portion. Thanks for the help 👍
Pretty much. Pretty much. Pretty much. Pretty much.
Ikr 😂
Pretty much.
POSSIBLY possibly
Lmao
Pretty much possibly knows more then u
Thank god!!! Every time iv seen an American do a review or a video like this they've gone "and this is the box, and this is the packaging" and spent like 5 minutes on bs. You just go, "chuck that" LEGENDDDDDD!!!!!!!
Totally cool guy!
Aftermarket speakers are better with an aftermarket amp. Unless your car is higher end and stock factory stereo is higher wattage output. If it's not, then you loose quite a bit of bass vs factory speakers
Very true about the wattage, but when it comes to replacing door speakers for aftermarket upgrades, you’re pretty much always going to lose bass regardless of it being amplified due to crossovers. Hence why we all install subwoofers to properly set the sound stage and bring those nice low frequencies back. And don’t forget the tweeters for the highs!
@@ETG311 what? Plenty of my cars I’ve only installed good stereos and speakers and never felt like I needed a subwoofer unless I wanted absurd bass.
I know this is an old comment but the bass that you “lose” is going to hardly make a difference, at least not enough for you to want to go spend 500+ minimum on a sub
@@AngerMaker413 500 on a sub damn I spent 250 and got a sub and amp
@@genuinealloy8316 yea 500 on a sub sounds like he's buying a sub installed in a box
Thank you for the explanation of speaker size at the beginning. Cleared up most of my questions about doing an install in the first 2 minutes of the video
I love these speakers 🔊 I have two inside a dual box in my middle console of my truck. They sound super crisp and clean and zero distortion at max volume
I’m late to the party. But this video was very helpful thank you man.
This is the most helpful yt tutorial I have ever seen. Keep up the good work
why would you not show us you clamping the red pieces together and how to cut them and put them in?!?! that's how you connect it and you don't show it??
Joshua Sarno Mainly because there are various methods of connecting two wires together. Soldering, Crimping (like in the video), and twisting the wires together are just a few options. Considering there are so many ways, we will make another video on how to securely and safely make electrical connections. And to answer your question, we didn't include that in the video for sake of time. Thank you for your feedback!
Joshua Sarno 5
Joshua Sarno .ed
Joshua Sarno .
CalebsAutoHelp a bro my 01 Buick regal has stock tweets and I want to replace them. Do I cut there wire to the stock one and wire the plug in part to the new tweets plug back in and it good to go or what? I'm lost af
Excuse me sir, do you know how fast you were going?
How you know witch cable to connect with the other?
Did you splice the speaker wires too ?
So how do they sound?
Kicker speakers sound very clear and they have nice bass in them
Do i have to check what size of the speakers i have inside of my door car panel ? Or all speakers have standards size? Thank you
J Jay Le yes. All cars are different metraonline.com will give you all the information you need. Just search your car and the year.
Y
Could have used a few links to the tools sales pages.
So how do you check which wire is negative and positive?
This was the best video of changing speakers I have seen mostly based on the fact your explained all the different ways of connecting instead of going HA YOU HAVE TO CHOP YOUR WIRES UP
How do I know which cables to connect together for the new adapter?
a krimp works fine? i read online you have to soldor it on
Do you not install the speaker grilles over the speaker?
Is this universal? Like on my toyota auris will be the same?
Thank you I feel confident with the wiring now! Appreciate it bro!
I got speakers in the back with no cables to be found. Where can i connect a cable to go to the speakers?
you didn’t mention that you can buy adapter cabels for the connector now i don’t have it bruh when i coulda bought adapters
what if there were no connectors on the existing speakers wires? Should the red go to the larger connector on the speaker?
how did you know how to put the correct polarity on the wires you crimped?
Awesome.i do have one question;what would happen if the wires are reversed?would it break the speakers or just sound shitty?
Thank you guus
Hello, i have installed an aftermarket pioneer stereo (deh- s320bt) in my car which says "output power: 50 (*4) watts" . Until how many watts RMS speakers can i buy? Cause i dont know if this "50" is watt RMS. For example if i place 80 Watt RMS speakers in my car, will the stereo be burnt?
I have found some speakers (Jbl stage2 604c) which are 45 watt RMS and 270 watt max power . Will they fit my car?
with some car audio speakers they require a 4way amplifier (not a subwoofer amp) the actual car speakers. i would love to see a video on how to install that
hey i got a question....i have a chevy cruze 2014 iam trying to install 6x9 in the rear deck. but my car came with no speakers or wires in the rear. but the hole is there but the actual carpet panel doesnt have the holes. do i have to cut out the holes so the speakers can go through or just leave it the ay it is and just install the speakers?
Is that a good speaker ? How does it sounds
A lot of effort put into this video. Thankyou
I'm a real noob when it comes to this and I have a question.
Are the wiers on all speakers the same ? I have an old car with crap speakers hooked up to a radio. Can I install new speakers with the same wier from the old speakers ? or will I have to get new wiers.
I fucked it up lmao
What is the biggest size?
I have a speaker that comes with built-in lights. Where should I connect its positive terminal so that the speaker lights turn on when I switch on my vehicle lights? Also where should I connect the ground wire? Pls help
Double check and see if the packaging for your speakers note what voltage the lights require. If it's 12v, you would need to run a wire from the speaker to another wire that turns on when the vehicle turns on, or to a fuse box where you could tap into a circuit using a fuse tap. The fuse tap option might be easier if you don't have a multimeter to probe wires with. You'd just pull out a fuse for something that turns on when your vehicle does, insert the fuse tap in its place, insert the original fuse into the bottom slot of the fuse tap, insert a new fuse in the top slot to protect your lights, then connect the positive light wire to the fuse tap.
As for the ground, find a bolt or nut that screws directly into metal that is relatively near your speaker (you might even find one with wires attached already, that is a grounding point), put a ring terminal on your wire, unscrew the nut or bolt, attach ring terminal, and screw back down.
The entire metal chassis of your vehicle is connected to the negative post of your battery, this is why you might come across a bolt with wires connected to it like I mentioned previously.
One last thing. If the packaging states that the required voltage for the lights is less than 12v, you're going to need a resistor on the positive wire going to the lights to drop the voltage down. I would assume they are 12v, but if not you can use a resistor calculator online to find what value resistor you'd need.
Sorry for the wall of text, but I hope this helps.
Sincerely, the guy from this video.
Will after market speakers sound better with the stock company fitted stereo?
My 6.5 speakers stick out more. They got to much depth...wut do i do?
burningknuckle26 you’ll just have to buy shallower speakers, there’s nothing you can really do.
So I did this and now they’re like super static, do you know what I did wrong?
Like anytime bass plays it sounds awful
But it plays, just gotta turn it down a lot
I need help guys and this video was awesome. I just got a 2006 chevy tahoe. I installed some 300w Pioneer speakers in front now i need back door speakers. My buddy gave me a pair of 6x9 and it says the back is 5x3/4 how do i mount them?
quick question. do i need an aftermarket radio for new speakers or no
If I wanted to to add a Center Dash channel to a stock 4-channel radio,
is it OK to use the left front positive lead, and the right front
negative lead with an 8 ohm L-pad to create a center dash mono channel?
I mean it was a good video for the most simple of parts but the crimping and splicing of the wires is pretty much all of the work
Hey quick question do you need to upgrade the alternator(which is a stock alternator) when you upgrade your speakers
No prolly not since the speakers arnt drawing much more power. You could measure you battery to double check with a voltmeter
Can I put actually subwoofers in my doors and still connect them to the car wiring
That would be a waste. Most if not all sub woofers require an amp to get the kind of power necessary to the speakers. Also sub woofers are highly specialized in the sound they deliver. Car speakers can deliver highs mids and low sounds where as the sub woofer is only lows. Your car would only be able to make the sound of a microwave really. Vocals could no longer be heard but the drums will sound fantastic.
@@fwuushy what if the subwoofer has a built in amp?
@@bigd3041 built in amps aren't attached to the cone. You could run your own wires from an amp to the sub
if the speaker's mangnetism is not there will it still work
Manjunath wtf no. Speakers work by using electromagnetism to create a magnetic field that oscillates the membrane and creates vibration, ultimately vibrating the air around it and making sound.
Oscillate the fuckin membrane
How do i know which is positive which is negative? I dont understand electricity.
Joe Barbaro with car door speakers it doesnt matter which one is positive and which is negative just connect the wires to either one. In this guys case its super easy because all you have to do is match small with small and big with big
Small pin is negative and big pin is positive
@@nathanielmillion4477 bullshit.
I tried doing that and my speakers were blocking my window from closing all the way down. What should I do in this situation?
You need to add a spacer in between the speaker and where it mounts. If you google the make and model of your vehicle along with "speaker spacer" you might be able to find pre-fabricated ABS spacers specific to the speaker holes of your vehicle. Maybe also check the Metraonline.com vehicle fit guide and see if they have anything for your car. If you can't find them for some reason, you might need to make some with some MDF or ABS, or if you don't have tools you can probably find a car audio shop to make some for you.
I'm planning on replacing my stock door speakers on my 2014 Nissan Sentra but I'm hearing some debate about 2 way and 3 way speakers. Some say 3 way speakers aren't any better that 2 way speakers. In fact they say it's worse because the tweeters restrict vibrations of the woofer. In your opinion which is better ? I'm looking for power and clarity.
Doamino41
In case of 3 way you hear a good combination of good bass and voice clarity. there no such thing like tweeters do affect bass or etc.. :)
In case of 2 way you hear more bass but a limited voice clarity.
Make sure to already select a good speaker!
Got it! Thank you
Doamino41 did you install aftermarket speakers with the stock radio ? If you did were there any changes in audio cause there's some things going around talking about how they would sound shitty if you use the stock radio with aftermarket speakers.
Actually I did replace all my speakers with Pioneers. 6 by 9s in the back and 6 1/2 in the doors. What a pain in the ass! Now it sounds louder but not clearer. That means I will need an after market double din radio with a SWC adapter. Some sources suggest an amplifier also. But yes you are right. Better speakers with the same crappy stereo won't sound much better.
The amount of videos where the guy has gone and bought every tool needed. 😂 how do you not have a socket set 😂
great video guys...thank you...the guy at the end looks blazed as hell..haha
What if I bought these oval shaped speakers but my car has a circular hole
gamer20playes Ask dad
@@vocilmw3642 i would but i havent seen em in 21 years
I love it when people say I dont recommend doing it this way, then they fo it that way.
Liking the Fallout 4 hat.
I'm pretty sure I can just use new speaker wire that has a positive and negative and just twist then clamp them onto the original wires of the car? Isn't that all that you actually bought ?just positive and negative wires cut the clip off then crimp it? I'm sorry I'm just about to do this to my car and was wondering thanks! Great video btw .
Love Sucks correct! The new speakers will come with a wiring harness in the box, normally with pressure fit connections pre installed (like in the video). If they don't, you can easily attach your own speaker wire between the speaker and speaker wiring from your car, either by using crimp connectors, or soldering. Best of luck with your install! Let us know if you have any further questions.
C
Wait that's it?
so instead of getting the adapter u can jut solder it rq? n just tape her up?
You can. But that's a really bad move. It makes future replacements much more difficult.
my factory harness inside the door has been cut. is there any other way to hook up my speakers?
John Cheng splice the wires and connect then physically by hand not to hard, just make sure you Match the negative and positive correctly.
Could you help me to make decision for my car audio upgradation?
I dont want a sub. Cs 6.5 front & Ks 6x9 3way rear, do this combination make good bass?
do revert pls :)
Mayank Swank you're not gonna get true bass unless you install a sub.
get a sub
Doesn't the new speakers needs an amplifier to run
No that's if you buy a subwoofer my dude
GREAT VIDEO! THIS HELPED A LOT!
How do you know what size to get?
What car do you have and what year
the ZOOM H1 !! at the end.... thats what i use! ... got 2 of 'em!
Great video, very easy to follow and understand!
you are welcome
The video got cut on the exact info that I needed😂Thanks for nothing.
Aren't those kickers much higher watts than most stock systems so it would be lacking power?
Colton Sailor Absolutely. The main reason we installed the Kickers is so that we can install an amp in the future, to more adequately power them. They still sound great without an aftermarket amp, they just lack volume.
That's why you get an aftermarket head unit so you dont have to get an amp
Very well done, informative video. Keep up the good work👌🏻
really dope video i appreciate this. thanks
He almost put a special word in front of rigged.
@Eric Furman no
Anyone recommend some good speakers for my 2011 Lincoln town car ? My stock ones are starting to go bad. I want some with some good sound a lil bass bump too. I used to have the sub and amp I’m the trunk but maybe I’m over that
Keep a sub in the back but then upgrade to some kickers or memphis
you went viral dude
11:03 Woah, he looks WAY different without a hat…
11:07 Oh… Duh 😂
really helpful video mate, thanks for taking the time to make it.
Why is my 260 watt speaker doesn't have more bass than my 20 watt speaker???
Are you using a stock amp ?
@@Bittenlucky nvm i got a aftermarket touch screen that have 300 watt and its good now
Where do u find ground in nissan 2010 i couldn't find it
That’s crazy I was looking up how to do it in my 02 LSE and he’s got an LS in the vid lol
My video paused outta nowhere during the intro right after "help" was shown. I was waiting a good 10 seconds to see how the car needed help
Im just going to take it to the shop
Pretty much.
Thanks bro!
Is anyone confused on why it says Caleb’s whatever then he goes hey my name is eli
Wow! That doesn't look hard at all. Thanks!
Brought to you and paid for by harbor freight. Nuff said 🤣
Haha when you said you didn't know of there was crimp tool there was one in frame on the right lol
Those are needle nose pliers :D
Source: Im the guy in the beginning of the video
nice video dude
Video was super helpful
Really kickers? You can get better for the price, they sell their names more than quality, but they’re ok.
What brand do u recommend
markus pully Dayton Audio all the way
JL audio, focal, or infinity NOT dayton or kicker 😂
Paul Flurry You just a bandwagon, try some Dayton 12’s and that would change ur mind, or Skar bc they pretty good too
Officially Isaiah i dont have anything against Dayton, they are good speakers but imho they are not the best. the subs are good tho..
wow he's a cute guy I love the way uses his hands tell us every little detail man in the detail not to not details tell us all the little details tell us the story
iwilleatyopussy I got it back door you can get the back door do my back door
Bro are you still alive? Channels been dead for 2 years...
What the hell is a shop without tools?
Are you assuming that I can't see the screw?
It's a joke.
Anyone else just yank their door panel off with no tools
How?? 😂
You get a better connection with butt connectors vs just tape when your car goes over bumps it can lose contact
Zack Ryan personally I prefer to use a soldering iron and heat wrap.
He said butt connectors vs tape. Everyone knows soldering and heat shrink is best but that's not what he fucking said lmao.
I might have the easiest solution
Just by 2 or 3 jbl speakers and put them in the door cup holders
Put charge cables in and they won't go empty.
Connect them.
And you got sound from left and right.
Ez to do and you only have to turn them on. Connect them with 1 press use your Phone for Bluetooth.
And done. Now you got great quality sound in your car after 2 minuts
Maybe not the loudest but hey, your'e just ruïning your ears if you turn the volume all the way up
So far I'm annoyed not talking loud enough or mic is too far away bud
u need a a cameraman
you wearing mascara ?
So you say test for positive and negative how about telling us how to actually do that!!!!
Hi :)
Lol lit.
Ramman02
Step 1. Don’t buy kicker speakers
Stanlley Pajdak
Haha! So many people say that. But I never had a problem with any of the stuff I bought.
Kicker is a good brand
Not a hater, but does this even need to be explained how to do?
This was literally just a video that covered common sense. The “specifics” that everyone was trying to find, got cut out (technical difficulties), while you were probably; blowing fuses, taping your own finger to a wire, and possibly mistook your own shadow for a burglar, causing you to have a liberal fuel anxiety attack. Now the actual information displayed on this video, consisted of how to take a door panel off a car (which has never been an issue, for any DIY’er, EVER), and an extremely drawn out tutorial on plugging in “the big one to the big one” and “small one to small one”. If you thought this video was in any way beneficial, y’all deserve each other. 👍🏼
I’m sorry that you feel that way about the content in this video. We posted it with the intent of teaching anyone how to upgrade their speakers, because not everyone knows how to. Additionally, saying that taking a door panel off a car has never been an issue for a “DIY’er” is quite far fetched. Most people have never removed a door panel, and now because of this video 200,000+ people have that knowledge. Thank you for your feedback.