Thank you for your message Bernard. We house most of our documentation in a virtual database here: spr.ly/6050uqKls. If this does not address your concerns, please reach out to a technical support person in your location. spr.ly/6051uqKlt
Thank you for your message. We house most of our documentation in a virtual database here: www.se.com/ww/en/download/. If this does not address your concerns, please reach out to a technical support person in your location.www.se.com/ww/en/work/support/country-selector/contact-us.jsp
Very Good Video! not that i can start and stop it. What about how to set the direction Rev/Fwd? Fault Reset? Current Warnings/Fault? We just purchased 8 more so any help would be appreciated, Thank you
Thank you for your message, Karm Khela. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp or reach out to a technical expert in your location here: www.se.com/ww/en/work/support/country-selector/contact-us.jsp
Hi Karm! Thank you for contacting APC by Schneider Electric. Please be advised that your concern has been endorsed to our Drives Team. They will assist you further with your concern. Kind Regards, Jurvy
HI , I WANT TO do communication Siemens S7400-H via on board MODBUS TCP , can i use onboard Ethernet/Modbus TCP Port ?? please guide my drive is ATV930
Thank you for your message, chintan bhavsar. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp
Thank you again for reaching out. We are unsure of what you are inquiring about. For direct assistance, please reach out to a technical expert in your location here: spr.ly/6057KDeXv
very easy to follow and precise guide, I was able to communicate with the VFD with a WinAC RTX soft plc in no time!
Hello, why don't you see the Profinet message type selection parameters in the inverter? Is it ok to configure PPO only in the SIEMENS TIA Portal?
Thank you for your message Bernard. We house most of our documentation in a virtual database here: spr.ly/6050uqKls. If this does not address your concerns, please reach out to a technical support person in your location. spr.ly/6051uqKlt
Hello, If iwant to use telegram 106 what is the parameter?
Thank you for your message. We house most of our documentation in a virtual database here: www.se.com/ww/en/download/. If this does not address your concerns, please reach out to a technical support person in your location.www.se.com/ww/en/work/support/country-selector/contact-us.jsp
Thanks
Dear
I want to communicate an S7-1500 PLC with several Altivar 320 and 630 drives.
Could you help me with a guide?
with Profinet?
@@lucaswiniciusdasilva5293 ON ETHERNET IP
Very Good Video! not that i can start and stop it. What about how to set the direction Rev/Fwd? Fault Reset? Current Warnings/Fault? We just purchased 8 more so any help would be appreciated, Thank you
Thank you for your message, Karm Khela. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp or reach out to a technical expert in your location here: www.se.com/ww/en/work/support/country-selector/contact-us.jsp
@@schneiderelectric I have and no one seems to know!
The manuals to not specify the inputs and outputs i am looking for.
Hi Karm! Thank you for contacting APC by Schneider Electric.
Please be advised that your concern has been endorsed to our Drives Team. They will assist you further with your concern.
Kind Regards,
Jurvy
@@schneiderelectric no one has contacted me yet
HI , I WANT TO do communication Siemens S7400-H via on board MODBUS TCP , can i use onboard Ethernet/Modbus TCP Port ?? please guide my drive is ATV930
Thank you for your message, chintan bhavsar. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp
please send me, hexcode parameter siemens to schneider profinet communication
Thank you for your message. For technical support or to find answers to your questions, please refer to our support center: spr.ly/6059K84ZT.
@@schneiderelectric, please communicates youn with them,
Thank you again for reaching out. We are unsure of what you are inquiring about. For direct assistance, please reach out to a technical expert in your location here: spr.ly/6057KDeXv
did you ever get a response from Schneider?