I've always thought those Venoms were the best looking speed/power boats and the alien cowl was definitely the way to go. Damn that thing is sexy as hell and yall did a great job laying it out. Awesome setup guys.
Where can you get the venoms from? I have a vking that I haven’t used in 10 years getting ready to start the process on the core stringers and transom but I’m liking the idea of a new venom
New subscriber here. Great job on rigging this boat. Yall should make the videos longer. But anywho great content and much love to ya brothers from Maryland❤❤❤
First, nice work on Tristyn's rigging, its looks super clean. I'm absolutely thrilled to see a new 'Hydrostream' come out of a mold. I have a red and black 2004 Venom with a 2005 280 ROS My boat was supposed to have been the one in the TRO video racing cars next to a slough somewhere in FL. Somewhere along the way the engine rigging has been messed up and unless I load the boat with passengers I cant get it over 80 without a deadly chine walk occurring. I would really like to know where you positioned the outdrive with respect to the plaining surface on this boat. I just raised mine by a 1/2 inch hoping to work this problem out. Unfortunately I also suffered a lower unit failure; which exposed worn out threads holding the carrier into my case. I've had to piece a new 15 inch lower together. Its been costly... But I hope to be spending 'Weekends On The Water' soon. I'd give anything to go on one of your runs with everyone. I live in WA State, sadly there are very few outboard enthusiasts and most of the Hydrostreams introduced in the state have vanished. I hope to hear back from you, thx in advance.
That is badass. Y’all did a great job on the setup, super clean. Only thing I think you should’ve done different is gone with center steer. Just my opinion though. Excellent work gentlemen!
Why are you drilling those transom holes without a Jig? I dont care how hard you try to keep the bit straight, it isnt. I guarantee you had a hard time getting those bolts lined up to bolt the jack plate.
Nope they went right in. If the jackplate isnt drilled perfectly then the jackplate goes on crooked. (Ive seen it too many times) I was a fabricator by trade for many of years, drilling holes straight is not a problem
@weekendsonthewater Beautiful boat and set up. Agree, if you can afford new, why buy a reclamation project. I've watched these on line, endless hours if one is a perfectionist. Rotten spongey floors, hidden rot in transom, yikes. Very fine work men. I was nervous for you on the drilling, though you tripple measured. I to, run up through the drill sizes. You may or may not have considered a poster board template which then may be taped to hull. Just like making a perfect fit gasket. Exceptional work and final results men!
@TroyPrewitt-fm7ic apparently Hydro Stream. I'm not sure where they are located. Probably Tennessee. It seems all the fastest boats come out of that area.
@@weekendsonthewater understandable 👍🏻well it looks sounds good. I live in lake Havasu work for Domn8er power. I have a 78 Kurtis Kraft 5/8 runner bottom. Pro gas 140’s on a good day. Love boating good luck stay safe ✌🏻
Man, 108 with no setup is wild!
was a good deal of setup, still sick 108 off the rip!
I've always thought those Venoms were the best looking speed/power boats and the alien cowl was definitely the way to go. Damn that thing is sexy as hell and yall did a great job laying it out. Awesome setup guys.
Love this type of content man keep it up!
That is an insane hull! Awesome build dude!
ALMOST NOTHING IN THE WATER BUT THE PROP👍
Where can you get the venoms from? I have a vking that I haven’t used in 10 years getting ready to start the process on the core stringers and transom but I’m liking the idea of a new venom
Still got the vking? Im interested. Where you located?
New subscriber here. Great job on rigging this boat. Yall should make the videos longer. But anywho great content and much love to ya brothers from Maryland❤❤❤
First, nice work on Tristyn's rigging, its looks super clean. I'm absolutely thrilled to see a new 'Hydrostream' come out of a mold. I have a red and black 2004 Venom with a 2005 280 ROS My boat was supposed to have been the one in the TRO video racing cars next to a slough somewhere in FL. Somewhere along the way the engine rigging has been messed up and unless I load the boat with passengers I cant get it over 80 without a deadly chine walk occurring. I would really like to know where you positioned the outdrive with respect to the plaining surface on this boat. I just raised mine by a 1/2 inch hoping to work this problem out. Unfortunately I also suffered a lower unit failure; which exposed worn out threads holding the carrier into my case. I've had to piece a new 15 inch lower together. Its been costly... But I hope to be spending 'Weekends On The Water' soon. I'd give anything to go on one of your runs with everyone. I live in WA State, sadly there are very few outboard enthusiasts and most of the Hydrostreams introduced in the state have vanished. I hope to hear back from you, thx in advance.
Awesome job guys! Boat is clean and looks awesome!
Don't forget the oarlocks and sleeves😁
Man I would have so much anxiety drilling all those holes in someone elses brand new boat!
I get enjoyment out of it😂
That's the fun part
Dang that thing flys I wonder if you feel like you're going to back flip cause the middle of the hull wasn't even touching the water
Great set up that boat turned out killer
Love the more technical stuff!
That is badass. Y’all did a great job on the setup, super clean. Only thing I think you should’ve done different is gone with center steer. Just my opinion though.
Excellent work gentlemen!
Sick. Not a pipkorn stream but I do really like them. Any idea on how many got produced?
Thanks for the video. Have sone good information coming within couple weeks. It will be on here first. 😊
Big block omc is what this boat needs
THAT is a beautiful boat! She's sleek!
Nice rigging!
That is fucking nice. Congratulations
Yes sir fast boat for sure. It's very streamline looking whats the cost of the hull?
Im unsure, you would have to contact the builder
Awesome boat, is that Nickajack lake just off I-24 in Tennesse at the beginning of the video?
Yessir!
'You all did a great job. It may be time for a Hi-perf shop of your own. Stay wet.
Great job guys,,,,, 108 is excellent first time out. Man that pad looks like it's a foot wide. How wide is it?
I might be wrong but i think its 11"
@@weekendsonthewater Thanks, looking at widening mine.
ruclips.net/video/-Pa8_Jkk1wc/видео.html
Why are you drilling those transom holes without a Jig?
I dont care how hard you try to keep the bit straight, it isnt.
I guarantee you had a hard time getting those bolts lined up to bolt the jack plate.
Nope they went right in. If the jackplate isnt drilled perfectly then the jackplate goes on crooked. (Ive seen it too many times)
I was a fabricator by trade for many of years, drilling holes straight is not a problem
awesome boat! What's going on with the stv now?
Stv was sold!
A new one is on order
they still make new hulls like this? why and for how much? there's SO many cheap or free to be redone out there.
Nothing beats a brand new boat!
@@weekendsonthewater I vehemently disagree.
@weekendsonthewater Beautiful boat and set up. Agree, if you can afford new, why buy a reclamation project. I've watched these on line, endless hours if one is a perfectionist. Rotten
spongey floors, hidden rot in transom,
yikes. Very fine work men. I was nervous for you on the drilling, though
you tripple measured. I to, run up through the drill sizes. You may or may not have considered a poster board template which then may be
taped to hull. Just like making a perfect fit gasket. Exceptional work
and final results men!
Awesome boat! How did you end up filming the opening scene at Jasper?
We passed right by it! So i was like yup we are doing a walk around there
@@weekendsonthewater Thats awesome I love it
very very nice boat
Hey Hunter, is that a 2 stroke?, thanks for the video.
Yes it is
Goodonya 🤙🤙enjoyed in Australia 🇦🇺
you dont use the mercury drill template? makes it alot easier too
Ive seen too many jackplates drilled crooked making the plate crooked on the boat, so i hand measure everything
@@weekendsonthewater thats crazy! if that works better for you thats great. i use my merc tool all the time though love it
loved it keep up the good work
who builds these boats now?
That boat is sick! Who built the motor?
Power performance engineering
Why no OMC
We do to many miles for an omc 😜😂
Hi, awesome vids.. Is there a contact number or email to get one of these hulls ?
Is this a new hydrostream
New and improved!!
Perfection !!!
Looks fun!
Wow wicked fast
Any updates on this baby?
Sick boat ❤
Where did hull come from?
East Tennessee
That is a beauty
Why no hot foot?
There is
name of dealer ? thanks
Venom performance boats
Is anyone building these boats now ?
Yes they are building these boats!
@@weekendsonthewater Who is building these Venoms & how would you go about getting one ?
@TroyPrewitt-fm7ic apparently Hydro Stream. I'm not sure where they are located. Probably Tennessee. It seems all the fastest boats come out of that area.
I know that park. 😊
what prop and pitch?
30 mercury et
Wow!!!!!!
bad ass!
WOW
Bad ass
ruclips.net/video/xq6h8zLMBec/видео.html
I hope you’re putting a hot foot in it. Bro, you didn’t put the seat in the middle. What is wrong with you?
Family boat
@@weekendsonthewater understandable 👍🏻well it looks sounds good. I live in lake Havasu work for Domn8er power. I have a 78 Kurtis Kraft 5/8 runner bottom. Pro gas 140’s on a good day. Love boating good luck stay safe ✌🏻
Put the other cowling on there looks way better
Should’ve put the seat in the middle and you should’ve got a tunnel hall instead stv Looks like you’re from the Midwest or east back east I get it now
Sold 130mph stv river rocket to buy this. Fast family boat