How do you connect the phase , and neutral at the float switch ?! Shouldnt only the phase go in the float(switch) and come back to the contactor to complet the circuit when watter level is up ?!
@jr electrical school Can you tell me what changes I should make in wiring so that my motor turns off when water level is low and turns on when water level is above set low level in float switch. This is for a .5hp multistage pressure booster pump on I’ve put on the terrace
I would like to know how this circuit is wired where the surface pump is replaced by a 220v submersible well pump that has a control box with the required starting and running capacitors. Great video. Thanks.
This is sort of what I need but not sure I have a water tank that gets filled up once a month by water truck. If I don’t catch that the tank is empty in time the pump gets hot sucking air and melts or warps the pvc pipes or burns up the booster pump i need something that I can just plug the power cord 120ac into that will cut off the power to the booster pump when the tank gets low. Is this setup what I need does it need to be wired differently or is there something easier that I can use to save my pump and pipes and precious water please and thank you sir
I think his connection is going to be wrong because i) there is no operating coil. ii) whether NC is connected with neutral and phase there will be short-circuited. please clarified me.
is it magnetic contactor? I just wandering coz its similar contactor and conector.. I cant understand how will the float switch command the coil of the magnetic conector to close and open the load?
You didn't mentioned or showned where the hot wire (red) connected in the contractor going to switch and likewise the Blue wire from switch to contactor. What is that point where Red and Blue wire meet up at the contactor?
I have seen many of your videos it's good! You have done a good job, I have a query I was searching on the net , but all don't fit the bill, I have a 3 phase 5hp water pump I need the following sensor : sump tank water level + timer on/ off , dry run - phase check. Auto on off...pls help.
I like your video and your explanation but why you are making your video so slow when you write a line that make us confusing. Finally thanks for the useful channel.
Dear friend if u connect neutral to float switch pls think ur connected load in off position what is the reaction.pls think about this or discuss with any seniors to confirm the safest way.I'm humbly requesting u pls don't suggest like this hazardous way to public.if u need more information about this call me 9790091294. I'll guide you. Thank you dear
Please review your diagram and specified your connection. Were is the coil line? Were did you top your line (red wire on the rigth side) no,nc or main contact.
This wiring is for - that specific pump filling that specific tank - is is NOT for that pump to DRAW from that tank. Hence, to Automatically fill the tank when almost empty and shut off when full.
It should be called a magnetic contactor and not magnetic connector. A magnetic contactor is a type of electrical relay to switch on or off large motors. it has a coil that activates the contacts. The float switch is connected to this coil in order to turn on or off the water pump.
I appreciate your efforts BUT you have to know lots of people in the world unable to read English, but they can speak and understand English. No need of music, If you brief himself it's too much beneficial instead of just looking and listening music.
It does not say the number for the Magnetic connector, I need to install a float switch or water level switch inside a sewage pipe to connect to my marcerator pump = DC 12 volt / min 6.5 max 10 Amps / model MP-3500-12 It is very difficult to find the right information Thanks
Do u know that your float switch connection is totally wrong? Why will you connect your float switch to live and neutral? A float switch act as a switch to turn on or turn off a system. So tell me why are u connecting it to both live and neutral
Thanks, but I have a question🤔 why neytral line was passed from float switch?? Actually, for me phase line had to be held from float switch, isn't it??
Single phase ,,,ki this is automatically operating system including add select switch manual and off used in this wiring But 3 phase wiring automaticall Operating we needed to nc no or selet switch used
Hello i have a 1100gph bilge pump and a float switch that says 20amp max. And on the bilge pump it says max 3.5amp draw. I was wondering what amp fuse do i need to put in the control panel Thanks
Is Me c0nTacT0r ka k0i b N0 NC c0nTacT usE nHi h0wA br0.JxT c0nTacT0r ki c0il k0 c0nTr0l kiyA GyA Hai Fl0aT SwiTch sE.bc0z Fl0aT SwiTch Khud Takreebun N0 NC JesA KaaM krTa Hai.Is c0nnecTi0n Me C0nTacT0r ki c0il k A1 Terminal pY PhasE DirecT diyA GyA Hai 2 p0le M.C.B k 0uT puT sE Aur NeuTral k0 Fl0aT SwiTch sE c0nTr0l kr k c0nTacT0r c0il k A2 Terminal per diyA GyA Hai.I h0pe k Apk0 SMjh A Gai h0Gi Mri baT ki.isi LiaY iTni DeTail sE bTaYa😊
Technically float switch shorts the circuit which trips the DP(MCB)....if such is the case then what is the fun of using magnetic conductor.....????🤔🤔🤔
Your spelling mistakes: Magnetic connector(contactor),singel phase(single phase),pume(pump)....and you didn't explained about capacitor connection... without capacitor single phase induction motor doesn't work... please make sure your information is correct before u post it👍
কানেকশন টা খুব বিপদ জনক। ২২০ ভোল্ট এসি ওয়াটার ট্যাংকের ফ্লোট সুইচ থেকে ম্যাগনেটিক কন্টাকটরকে অপারেট করছে। ফ্লোট সুইচ লিকেজ হলে ট্যাকের পানির লোহার পাইপ সার্কিট ক্লোজ করবে। আর ইউজার পানির লোহার ট্যাপ ধরলে লিকেজ এসি ভোল্টেজ এর কারনে আহিত হতে পারেন।
Good job engr.nkkadag2 ng kaalaman po.
Thanks for watching this video
thanks so much for this am going to learn more about electrical continue doing this children of God
You are very welcome
@@JrElectricSchool sand me the auto &maneva control
How do you connect the phase , and neutral at the float switch ?! Shouldnt only the phase go in the float(switch) and come back to the contactor to complet the circuit when watter level is up ?!
Yes you said it me also confused
None of these videos explain how to actually wire a contactor with float switch. There is always a few steps missing or not explained at all
@jr electrical school Can you tell me what changes I should make in wiring so that my motor turns off when water level is low and turns on when water level is above set low level in float switch. This is for a .5hp multistage pressure booster pump on I’ve put on the terrace
I would like to know how this circuit is wired where the surface pump is replaced by a 220v submersible well pump that has a control box with the required starting and running capacitors. Great video. Thanks.
So you are saying its not possible without the contactor?
This is sort of what I need but not sure I have a water tank that gets filled up once a month by water truck. If I don’t catch that the tank is empty in time the pump gets hot sucking air and melts or warps the pvc pipes or burns up the booster pump i need something that I can just plug the power cord 120ac into that will cut off the power to the booster pump when the tank gets low. Is this setup what I need does it need to be wired differently or is there something easier that I can use to save my pump and pipes and precious water please and thank you sir
Is it okay if i will not use the magnetic controller?
no you can use magnetic contactor
I think his connection is going to be wrong because i) there is no operating coil. ii) whether NC is connected with neutral and phase there will be short-circuited.
please clarified me.
does it matter if the float switch wire is a few hundred feet long?, or should a 24v dc supply be used for that length of wire?, with a dc coil.
is it magnetic contactor? I just wandering coz its similar contactor and conector.. I cant understand how will the float switch command the coil of the magnetic conector to close and open the load?
Yah
This is simple and good result
You didn't mentioned or showned where the hot wire (red) connected in the contractor going to switch and likewise the Blue wire from switch to contactor. What is that point where Red and Blue wire meet up at the contactor?
Are you sure the connection of the float switch?
I have seen many of your videos it's good! You have done a good job, I have a query I was searching on the net , but all don't fit the bill, I have a 3 phase 5hp water pump I need the following sensor : sump tank water level + timer on/ off , dry run - phase check. Auto on off...pls help.
please watching this video
ruclips.net/video/EGMH4TrNJs8/видео.html
U are the junior electricity technician..👍 connection,,⚡⚡⚡💥💥💥 very well???
Yes, thanks
Very nice video.
Thank you very much!
Can we use float switch directly without MCB... The max current rating mentioned on the switch is 16(8)A, while 1 hp motor has 1 A current
you can use float switch without MCB no problem but MCB is safety for your electricity short circuit
I like your video and your explanation but why you are making your video so slow when you write a line that make us confusing. Finally thanks for the useful channel.
If you make the line faster that's will be fine. If anyone didn't understand he can easily stop the video. Again thank you.
your welcome
Damn I am going to learned more about this better than attending school lol.
Congratulations Very good 💙
Thank you!!
Cable ki length badane ke lea wire minimum kiatne mm ka use kar sakte he
0.5 mm ki cable use kar sakte he??
Is this a 220v scenario?
After this connection, which current will go to float switch?
Ac or dc?
If d.c then how much current?
I'm asking you sir one doubt why you are connecting neutral to float switch?
Neutral is safer in water
Dear friend if u connect neutral to float switch pls think ur connected load in off position what is the reaction.pls think about this or discuss with any seniors to confirm the safest way.I'm humbly requesting u pls don't suggest like this hazardous way to public.if u need more information about this call me 9790091294. I'll guide you. Thank you dear
what the connection will be if i want the pump off when the Tank is empty and the pump on when its full
Can we also used it without magnetic contractor?
no its problem you can use magnetic contractor
Assalamualaikum Vai, very helpful video, can I know which software use for electrical drowning
Thank you
Hallo mercury float is not to be connected to the coil point of the power cotactor it may fail.
How many watts is your magnitec conductor?
you can use magnitec conductor for single phase water pump 20Amp. Thank you
Bonjour
Is situation ma kya motor autometic off on hoga.
ha motor autometic off hoga
Please review your diagram and specified your connection. Were is the coil line? Were did you top your line (red wire on the rigth side) no,nc or main contact.
your feedback is very important for me i will review
Thank you.
I have panic :(
This is what I ask my self
sir please can you tell me what are the softwares are used for making this kind of videos.pls
we are used animation
I want to speak sometime
@@ELECTRICALINFOTamil yes you can tell me now
@@JrElectricSchool ur mail id please
@@ELECTRICALINFOTamil there is no problem you can say hear what you want to say
What are the contacts to be used on the magnetic contactor
32amp contactor used
How many chance of short circuit if we dont use MCB and MC
maybe 99.9%
Thanks for watching
This wiring is for - that specific pump filling that specific tank - is is NOT for that pump to DRAW from that tank. Hence, to Automatically fill the tank when almost empty and shut off when full.
Thank you so much for share your opinion
It should be called a magnetic contactor and not magnetic connector. A magnetic contactor is a type of electrical relay to switch on or off large motors. it has a coil that activates the contacts. The float switch is connected to this coil in order to turn on or off the water pump.
Thank you so much for share your opinion
very good video sr
Thank you very much
please subscribe this channel for more update
It is a rong diagram
Hello, will this work for 2hp submersible?
yes
Please, what app did you use to draw this circuit diagram
I appreciate your efforts BUT you have to know lots of people in the world unable to read English, but they can speak and understand English.
No need of music, If you brief himself it's too much beneficial instead of just looking and listening music.
Thank you
Magnetic connector 3phase OR single phase ?????
Sir ye jo blue wite ha wo kya phase se connect kra ha
ne he a neutral wire
@@JrElectricSchool sir samajh nahi aya .mare ghar me cramptom ka contact box ha kuch bataye please
Good work
Thank you so much 😀
What is the amperage rating of the magnetic contactor being used?
32apm
Is it okey if i use 30 amp of breaker?
Is the magnetic connector the same as relais?
no
@@JrElectricSchool Is it the same as magnetic contractor? I did Google magnetic connector. I could'nt find anything about it.
Please explain how is the connection if the float valve reverse scenario?
Nice job
Nice very good sir.
Many many thanks
Very usefull information thank u so much sir
Welcome
Sir 12v waly motor p kam kary ga...?
DC motor hoga tu kam nehe kare ga
NICE WORK
Thanks
please subscribe this channel
It does not say the number for the Magnetic connector, I need to install a float switch or water level switch inside a sewage pipe to connect to my marcerator pump = DC 12 volt / min 6.5 max 10 Amps / model MP-3500-12
It is very difficult to find the right information
Thanks
Do u know that your float switch connection is totally wrong? Why will you connect your float switch to live and neutral? A float switch act as a switch to turn on or turn off a system. So tell me why are u connecting it to both live and neutral
Coz he doesn't know what hes doing!lol
Kindly explain briefly on the connections of the magnetic contactor. Thanks
water pump automatic control in float switch
Which software sir you are using for this video
we making videos animation program
Thank you. please subscribe this channel
ISME BYPASS SWITCH CONNECTION KARNA HOGA TO KAISE HOGA
i will try to make video on your topic.
Thank you.
Love your work
my pleasure
Anna chala bhaga chapparu
sorry i am not understand you language
please bangla,english,hindi
Thank you.
Which app do you use to make these type of animation
filmora wondershare,sony vegas pro,
adobe after effects,adobe premiere pro,
adobe photoshop,microsoft office.
please subscribe this channel
I am impressed bro
Thank you so much
Please sir lunch a video for mcb box to inverter connection in single wire
i will try to make video on your topic.
Thank you.
Thanks, but I have a question🤔 why neytral line was passed from float switch?? Actually, for me phase line had to be held from float switch, isn't it??
Single phase ,,,ki this is automatically operating system including add select switch manual and off used in this wiring
But 3 phase wiring automaticall
Operating we needed to nc no or selet switch used
Hello... Can you add an APC to the pump? Paano yong wiring?
i will try to make video on your topic.
Thank you.
Y un circuito para prender o activar la bomba en directo, cuando se ocupe. En español si es posible, muchas gracias
please Bangla,Hindi,English
Flot switch connect to the contactor coil supply(A1-A2)???
float switch connect only contactor A2
Lucking
Hello i have a 1100gph bilge pump and a float switch that says 20amp max. And on the bilge pump it says max 3.5amp draw. I was wondering what amp fuse do i need to put in the control panel
Thanks
What is the meaning of N and L? what blue wire means?
L Line
N Neutral
blue means float switch wire
Good evening sir,what is the require MCB amp or watts and magnetic contactor for motor pump of 0.50hp and 1.50hp..
you can use MCB 32amp, magnetic contactor 240, and motor pump 2hp singel phase. Thank you
please subscribe this channel
Good
Thanks
It's complicated than I thought, need many utilities
Thanks for share your opinio
How about if we put overload on magnetic contactor video pls
You have to reduce the voltage passed to the float
yah software konsa sa istemal Kare hamen bhi bata sakte hain
our animation team making this videos
Thank you so much
please subscribe this channel
Contactor ka NC contact yaa NO contact use mein hai
yes
@@JrElectricSchool nc or no contact
@@JrElectricSchool nc or no contact
Is Me c0nTacT0r ka k0i b N0 NC c0nTacT usE nHi h0wA br0.JxT c0nTacT0r ki c0il k0 c0nTr0l kiyA GyA Hai Fl0aT SwiTch sE.bc0z Fl0aT SwiTch Khud Takreebun N0 NC JesA KaaM krTa Hai.Is c0nnecTi0n Me C0nTacT0r ki c0il k A1 Terminal pY PhasE DirecT diyA GyA Hai 2 p0le M.C.B k 0uT puT sE Aur NeuTral k0 Fl0aT SwiTch sE c0nTr0l kr k c0nTacT0r c0il k A2 Terminal per diyA GyA Hai.I h0pe k Apk0 SMjh A Gai h0Gi Mri baT ki.isi LiaY iTni DeTail sE bTaYa😊
What is this method . Please tell
water pump auto control
Thanks for watching
pwde po ba yong motor palitan ng soleniod valve? same connection lang din ba? thank you for reply 😁
Hello sir I can't understand how it works u r giving both phase and netural to the float switch.pls make live circuit and explain don't be confuse
i will try to make video on your topic
Thank you so much
I have one project on this. Pls explain me as soon as possible
@@naveethnsa85 plz visit
tech with MNA
What will happen in case we loose neutral and you still have the phase on the contractor?...
Cuando una instalacion con doble tamque d agua
sorry i am not understand your language
please tell Bangla Hindi English.
Thank you
Sir idol, how to make diagram of vfd with floatless relay?
i will try to make video on your topic.
Thank you.
The disco music is extremely distracting
i am so sorry for music problem
Good job
Thanks
Please indicate the wiring connection of water pump
Good work.
Check your spelling.
Contactor
Breaker
Means
Magnetic contactor
Single phase
Pump
Thank you so much for watching this video
Or bhai aapka channel monetize ho gaye kya
Anna float switch ku neutral kodukanuma
sorry i am not understand you language
please bangla,english,hindi
Thank you.
The neutral is only going through the float switch and then to the magnetic coil to get the closed circuit.
@@palaniyarsaransaran9580 thanks anna
thanks
Welcome
Help to explain its working mechanism
Technically float switch shorts the circuit which trips the DP(MCB)....if such is the case then what is the fun of using magnetic conductor.....????🤔🤔🤔
Thanks for the great work u do,but what are the initial requirement to study electric installation and maintainance with ur university?
Will upload soon
Can we use single pole mcb?
sure no problem
Thanks for watching
Paano pag.merong overload relay sir, pwede pakita diagram?
V good thanx
Most welcome
Good.
Thank you!
Your spelling mistakes: Magnetic connector(contactor),singel phase(single phase),pume(pump)....and you didn't explained about capacitor connection... without capacitor single phase induction motor doesn't work... please make sure your information is correct before u post it👍
কানেকশন টা খুব বিপদ জনক। ২২০ ভোল্ট এসি ওয়াটার ট্যাংকের ফ্লোট সুইচ থেকে ম্যাগনেটিক কন্টাকটরকে অপারেট করছে। ফ্লোট সুইচ লিকেজ হলে ট্যাকের পানির লোহার পাইপ সার্কিট ক্লোজ করবে। আর ইউজার পানির লোহার ট্যাপ ধরলে লিকেজ এসি ভোল্টেজ এর কারনে আহিত হতে পারেন।
ekane Neutral dara control hobe float switch Phase deya hobe na
Is it not too costly???
some costly but it is good and safe
Thank you so much please subscribe this channel
Any issues for the voltage veryetion
maybe no
Thank you
good
Thanks
நல்லது
நன்றி..
please bangla,english,hindi
@@JrElectricSchool,
Good job
Thank u
@@sooriyajeyasooriyan7094 you welcome
Bro please create a video 3 phase house wiring full detail
We will try
Thank you