Hi Rajas, Very nice video and thanks for uploading. I have a RX100 and I am going to open the engine mostly to inspect the connecting rod (giving slight noise) Also I will be replacing the clutch plates. This video will surely help. Good job bro.
Thanks for uploading the videos, it's very helpful videos for rx lovers. well most of the parts you covered both for rx100 and rx 135. if possible make something on Electrical wiring and all. that will be very helpfull
hey Rajas, I think you forgot to add HOW NOT TO in front of the title or even better you could simply rename it to How to rebuild an engine using a hammer and tyre iron.
Use mapgas to heat up the case and the bearings will drop straight in. As has already been said never ever hit a bearing the way you are. And never force the crankshaft in as you did. It will throw the crank out of balance. Use a puller or heat a steel bar up and place it on the bearing for a couple of minutes and the crank will drop straight in with no damage.Why have you fitted a gasket between the two crankcase halves, it does not need one. I could go on with all that is wrong with this build. I suggest you put the hammer down, buy some proper tools and learn how to assemble an engine correctly.
You r right sir.. Even though people came to flex there dramas in you tube..its panic. He did not know how to fix a crank bearing and crank shaft..properly with proper tools.. Its ironic..tragidy now a days..
My mechanic says, gasket shouldn't be used for crankcase. It increases the distance between the two halves and creates problems like power loss and gear shifting. Please put your views.
I could be a good video if you use appropriate tool for right part of engine not to use hammer on bearings use dead hammer or use cold method or hot method .overall good efforts but need to improve it please.
The 2 fork shifts for gears 1st,2nd and 3rd are identical?. Same thing?. My vehicle have gear slipping.. one of this fork shift got damaged.it is hard to find this part.is it really same? The numbers showing on it is different.
+Aditya Roy yup you r right ....it's the other way around ....but its a spur gear so should not be any problem.....but let me confirm this...and I'll update you on this Thanks for pointing out the mistake I totally missed it :)
You need not be a wiring expert just to check for any dissconnections or loose connection. Follow the wiring diagram if needed. If the bike was running fine before restoring the it might be just a minor problem.
hii rajas bro.... i have problem in my rx100 mene apni rx ko abhi 2 week pehle restore karaya hai ..50mm gouest poiston dala hai... $ bolck original old yamaha ka hi hai....... mejhe problem ye aa rahi hi ki bike me pickup nhi aaa rha ..plz suggest me bike ko kitna time(km) lagega sahi pickup aane me
You are wrong .... Even though people came to flex there talent..now a days.. in 'you tube."...its panic...! So first you please taught the working principles. Than use proper tools, while fitting a bearing or crank Than only you adress people ." He did not know how to fix a crank bearing and crank shaft..properly with proper tools.. Its ironic..tragidy now a days..!" So please don't go rude any time.
I am attaching a link for workshop manual. in that youll find a complete wiring diagram on page no. 6-1 so refer that if you like. if you still facing a prob about a particular component then ill try and make a video on that. link to download workshop manual - drive.google.com/open?id=0B4gusOWOdLHLMzVkYlNFVm1Qdms
My dear friends why u hit the bearing with hammer??? And why u let ur crankcase dirty?? And why u hit the crankshaft when put in??,, my brother i suggest u to use special tool to assembly all of that,,
+Anita Bika I'm running no 4 .....I don't know the prices ....but my advice would be if you have oem block on your bike then don't replace ....coz the one which you get in spares r not of OEM quality ...so my advice will be insert a sleeve in your original block and use that ...once u insert a sleeve you can again start from std size piston.
+JAYAKRISHNAN bala use rod or a screwdriver and hold it against the magneto. stuck the other end in sprocket teeth, so that it locks the sprocket in place for you to unscrew the nut.
Coz in many cases reed valve is the real culprit...ppl change crank bearings n engine bearing but it doesnt helps like in your case...reed valve usually costs around 450 -500...dont buy aftermarkets use orignal one.
Brother, How much does it cost for this kind of repair? Let's say I let the mechanic do everything, how long does it take to complete the job and cost, please? Thank you!!
Hi there, like to tell you something , that is you actually forgot tightening all the nuts with a proper torque wrench giving exact value, gauge has to checked in piston ring, and like many more things where has to be done, the performance comes after all measurements. You did lots of mistakes while fitting like bearing, clutch plates, friction plates. Plz next time use of proper tool's and then make video. Regards
Your videos help to understand the heart of an RX. Great work.
Heat the crankcase freeze the bearings it'll slide in effortlessly.
exactly
Hi Rajas, Very nice video and thanks for uploading. I have a RX100 and I am going to open the engine mostly to inspect the connecting rod (giving slight noise) Also I will be replacing the clutch plates. This video will surely help. Good job bro.
thanks man!!!!! and all the best.
This tutorial is absolutely helpful Rajas
Thanks for uploading the videos, it's very helpful videos for rx lovers. well most of the parts you covered both for rx100 and rx 135. if possible make something on Electrical wiring and all. that will be very helpfull
I am exactly 500's viewing-person of your video.
hey Rajas, I think you forgot to add HOW NOT TO in front of the title or even better you could simply rename it to How to rebuild an engine using a hammer and tyre iron.
Ek no. 🙏
Use mapgas to heat up the case and the bearings will drop straight in. As has already been said never ever hit a bearing the way you are. And never force the crankshaft in as you did. It will throw the crank out of balance. Use a puller or heat a steel bar up and place it on the bearing for a couple of minutes and the crank will drop straight in with no damage.Why have you fitted a gasket between the two crankcase halves, it does not need one. I could go on with all that is wrong with this build. I suggest you put the hammer down, buy some proper tools and learn how to assemble an engine correctly.
You r right sir.. Even though people came to flex there dramas in you tube..its panic.
He did not know how to fix a crank bearing and crank shaft..properly with proper tools.. Its ironic..tragidy now a days..
Whoa alas the assembly video is here 👍😃
+mohd saad heheh yes mohd Saad .....sry to keep you waiting this long :p
My mechanic says, gasket shouldn't be used for crankcase. It increases the distance between the two halves and creates problems like power loss and gear shifting. Please put your views.
Really appreciate the hardworknbro
Great video, thanks!
Clean the entire engine with the brake cleaner or any degreaser not rub with the hacksaw blade
Super bro do more thanks
Nice Video Brooo...
Sir Yamaha Rx 100, enging, me compreshar kaam lag raha hai, reesh, chor ane par band ho jati, hai, ring piction, dalane, se tik ho jayegi,.
I could be a good video if you use appropriate tool for right part of engine not to use hammer on bearings use dead hammer or use cold method or hot method .overall good efforts but need to improve it please.
Are dada te neutral chi position cha ball hota to nahi dakhvla ..?
The 2 fork shifts for gears 1st,2nd and 3rd are identical?. Same thing?. My vehicle have gear slipping.. one of this fork shift got damaged.it is hard to find this part.is it really same? The numbers showing on it is different.
My doubt is that, do the crank and its moving parts of RX get sufficient lubricant from the 3% 2T oil we mix with petrol ?
Hello sir Rajas G i have one question
Can you please suggest me I want to fix nitrogen shocks rear for my rx 100
Which is the best fit
Don't use still hummer
Use,proper tools like brass hummer and hard plastic material hummer
bro you have installed your gear sprocket idle other way round..change it before it damages itself along with your gear kick
+Aditya Roy yup you r right ....it's the other way around ....but its a spur gear so should not be any problem.....but let me confirm this...and I'll update you on this
Thanks for pointing out the mistake I totally missed it :)
cool bro.. my assembly has finished but it is not generating any spark, need to get it checked with a mechanic
Aditya Roy check all wiring connections. It happend with me missed connecting cdi wire.
mohd saad i know the fault is with the wiring, but i am no wiring expert.. have to take it to a mechanic
You need not be a wiring expert just to check for any dissconnections or loose connection. Follow the wiring diagram if needed. If the bike was running fine before restoring the it might be just a minor problem.
hii rajas bro.... i have problem in my rx100 mene apni rx ko abhi 2 week pehle restore karaya hai ..50mm gouest poiston dala hai... $ bolck original old yamaha ka hi hai....... mejhe problem ye aa rahi hi ki bike me pickup nhi aaa rha ..plz suggest me bike ko kitna time(km) lagega sahi pickup aane me
Super video All in one
please Make a video of Electrical system of Bike
Any particular thing in electrical system, that you want me to cover.
Headlight indicator blinking issue and horn !
Yamaha rx 100 main kon konsi bearings lgta hain with number?
Rx 100 mein six hole silencer lagane ke baad bhi sound loud nahin aa raha hai. Kya aap reason bata sakte hai
Thanks for your video. I subscribed you
Thank you for showing your support. :)
Keep it up👍
You are wrong ....
Even though people came to flex there talent..now a days.. in 'you tube."...its panic...!
So first you please taught the working principles. Than use proper tools, while fitting a bearing or crank
Than only you adress people ."
He did not know how to fix a crank bearing and crank shaft..properly with proper tools.. Its ironic..tragidy now a days..!"
So please don't go rude any time.
Sir i want to ready my rx 135 bike. Please tell me where i have to give you or meet you
Brother how to increase height of the fornt fork pipe?
Plz make the same kind of video of libero 125 yamaha..
Bro tell about oil change in Yamaha Rx 100 give complete details where oil flows where it consumed
Bai mera Rx 100 engine oil ka rah hai sayad iske leye mujhe kya karna hoga
Never tap bearings
Bro, Can I get total estimation for fully restoration of RX100 , and your workshop location tooo.
brother please make a video on wireing also with full connections.. please...
I am attaching a link for workshop manual. in that youll find a complete wiring diagram on page no. 6-1 so refer that if you like. if you still facing a prob about a particular component then ill try and make a video on that.
link to download workshop manual - drive.google.com/open?id=0B4gusOWOdLHLMzVkYlNFVm1Qdms
My dear friends why u hit the bearing with hammer??? And why u let ur crankcase dirty?? And why u hit the crankshaft when put in??,, my brother i suggest u to use special tool to assembly all of that,,
bro plz tell me which cylinder size are u using n wht are the prices of original rx100 n rx135 standard cylinder piston kit????
+Anita Bika I'm running no 4 .....I don't know the prices ....but my advice would be if you have oem block on your bike then don't replace ....coz the one which you get in spares r not of OEM quality ...so my advice will be insert a sleeve in your original block and use that ...once u insert a sleeve you can again start from std size piston.
Why hammer the bearings and cases? Use a nylon hammer instead
Bro how do you tighten small sprocket wheel nut?
+JAYAKRISHNAN bala block the rear wheel.
Rajas Gadkari I was removed the engine from the frame.... I needs to replace small sprocket, how can we remove and replaced it
+JAYAKRISHNAN bala use rod or a screwdriver and hold it against the magneto. stuck the other end in sprocket teeth, so that it locks the sprocket in place for you to unscrew the nut.
Broo u make vedio for new bike pulsar n all detalis like bearing n t chain n all of parts plsssss
Bhai i want same sount in my rx... please ya topic war ek video banav same ya bike sarkha sound paije please bhau
ill make try to make video on this ....
And that's how you don't replace a bearing.
Full wiring kise feeting kartay hai video banao
9:20 I lost my eardrums 🙂🔫
Ye wet kaha milyga
how much bearing in engine
I have replaced the bearings and reset the crank.
But still there is some.noise near bore
Like this. ruclips.net/video/zW91KYslCOI/видео.html.
It is running in new bore piston.
Change reed valve
mohd saad is it because of reed valve? Can u explain bro?
mohd saad jus a doubt
Coz in many cases reed valve is the real culprit...ppl change crank bearings n engine bearing but it doesnt helps like in your case...reed valve usually costs around 450 -500...dont buy aftermarkets use orignal one.
Hi Rajas if I need some help for assembling my RX100 then you can help me?
Yes, surely. You can DM me on instagram @rajasgadkari
Or mail me my email address is rajasgadkari@gmail.com
Aap ka dukaan kaha par h
Brother, How much does it cost for this kind of repair? Let's say I let the mechanic do everything, how long does it take to complete the job and cost, please? Thank you!!
it should cost around 2000 - 2300 rs , including labor .....duration not more than 2 days.
Thank you so much!
My bike problem clutch noise plz help bro
Crean ka Karcha kitna hai
Hi there, like to tell you something , that is you actually forgot tightening all the nuts with a proper torque wrench giving exact value, gauge has to checked in piston ring, and like many more things where has to be done, the performance comes after all measurements.
You did lots of mistakes while fitting like bearing, clutch plates, friction plates.
Plz next time use of proper tool's and then make video.
Regards
Rx135 5,speed 2000 model coneccting road milega @,price
Aap kidhar ke ho
Aurnagabad, Maharashtra.
Bro please help just now fully restored but 3 gear problem how to fix it
+Vignesh P three gears or 3rd gear?
What is the prob exactly?
Rajas Gadkari when I put the third gear Automatically natural
Vignesh P ok...kya 4th gear me ja Rahi he gadi ??? Ya 3 se age nahi ja Rahi?
Ap modefy karna ha to Rx Ko 4 stroke armachor aur magnat laga ka dehkaw top bolaga ap tof modefakashon karna walaho ap sakaga
What is the total price
haha . in the philippines the name rx 100 is rs 100 no crank case gasket and diffirent cylinder block.
Suzuki Max hundred start Nahin rahi ho rahi hai ho jayegi RPM set Nahin ho raha hai
How can i contact you brother
Ye gari slow me ni khari hori
Na munna na, bearings ko hathode se nahi marna chahiye, use proper tools.
Bhajan Meera RX Undertaker main engine oil chamber Fat Gaya repairing Mein Kitna Padega
4 no crank rod 🧐
Pestan pen ma bus sestsm kaameyaba ha ha kalaa pucha ha mestare
Bro any contact details of you i have some problems with my engine rx100 1994 model
you can DM me on instagram @rajasgadkari or you can mail me at rajasgadkari@gmail.com
Hi