Hola buen día muy buen video gracias por la explicación, tienes algún video para el desarme del fusor de la Hp M551?. Por otro lado la grasa que ocupas para las Hp 4015 RM1-4554 o RM1 4579 necesita una grasa de alta velocidad, alguna marca o link de compra en aliexpress o algún otro lugar donde adquirir la correcta ?, de antemano muchas gracias
Buenas tardes! Excelente video, buena explicación. Realice el proceso como el video pero al encender da error 50.22.00 error de fusor. Alguna indicación? Gracias
Thank you for your question. Please note error 50.22.00 means the machine does not detect the heating element is warming up. Following is the troubleshooting procedure: 1. After getting the error check if the fixing film is hot or cold. If it is hot, then the likely reason of the problem is that the thermistors inside the fuser unit are dirty or not properly seated. Reassemble the fixing film assembly making sure the thermistors are clean and properly seated. If the fixing film is cold, then proceed to step 2. 2. Check the resistance between fuser unit contacts as it is shown at 8:53 in the video (the normal resistance for 110V fuser units is lower than showed in the video). You will likely find the circuits are open. If so, you will need to find where the circuit is exactly open: o The heating element connector is not fully seated o The thermoswitch is open o The heating element is installed in wrong direction o The heating element is broken or defective Thank you for your interest!
Excelente, no me parece correcta la colocación de la grasa sobre el heating, yo la distribuyo uniformemente sobre el centro del calefactor en todo el largo. Cómo ejemplo dibujar un círculo y sobre la parte de arriba de este, una línea horizontal, el círculo sería el rodillo de presión y la línea horizontal, el heating. Saludos
Thank you for your input! We appreciate it. CET recommends smoothing out the grease on the heating element and removing the excess grease. That reduces the risk of the excess grease becoming oxidized and contaminating the working surface.
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Thanks so much... This really help alot. I really appreciate you 💯 you saved my ass today.
Hola buen día muy buen video gracias por la explicación, tienes algún video para el desarme del fusor de la Hp M551?. Por otro lado la grasa que ocupas para las Hp 4015 RM1-4554 o RM1 4579 necesita una grasa de alta velocidad, alguna marca o link de compra en aliexpress o algún otro lugar donde adquirir la correcta ?, de antemano muchas gracias
Buenas tardes! Excelente video, buena explicación. Realice el proceso como el video pero al encender da error 50.22.00 error de fusor. Alguna indicación? Gracias
Thank you for your question. Please note error 50.22.00 means the machine does not detect the heating element is warming up. Following is the troubleshooting procedure:
1. After getting the error check if the fixing film is hot or cold. If it is hot, then the likely reason of the problem is that the thermistors inside the fuser unit are dirty or not properly seated. Reassemble the fixing film assembly making sure the thermistors are clean and properly seated. If the fixing film is cold, then proceed to step 2.
2. Check the resistance between fuser unit contacts as it is shown at 8:53 in the video (the normal resistance for 110V fuser units is lower than showed in the video). You will likely find the circuits are open. If so, you will need to find where the circuit is exactly open:
o The heating element connector is not fully seated
o The thermoswitch is open
o The heating element is installed in wrong direction
o The heating element is broken or defective
Thank you for your interest!
Great video.
Thank you!
excelente vídeo
Glad it is helpful!
Excellent!
Thank you!
Great.
Thanks!
@@CETGroupUSAInc And Great again.
So clear/
Excelente, no me parece correcta la colocación de la grasa sobre el heating, yo la distribuyo uniformemente sobre el centro del calefactor en todo el largo. Cómo ejemplo dibujar un círculo y sobre la parte de arriba de este, una línea horizontal, el círculo sería el rodillo de presión y la línea horizontal, el heating. Saludos
Thank you for your input! We appreciate it.
CET recommends smoothing out the grease on the heating element and removing the excess grease. That reduces the risk of the excess grease becoming oxidized and contaminating the working surface.
Great video
Thank you!