Design Centrifugal Pump use Solidworks
HTML-код
- Опубликовано: 20 авг 2024
- In this video i show you how to design a Centrifugal Pump in Solidworks.
I hope this video will help you to design use solidworks
Just enjoy it, and like it.
Thanks For Watching
Click this link below to see playlist Solidworks Tutorial For Beginner
• Solidworks Exercise 1 ...
And click link below to see Solidworks Lesson
• Solidworks Tutorial Le...
Follow my Instagram @thirdkoniago if you want to get more information
/ thirdkoniago
#ThirdKoniago #SolidworksTutorial #CentrifugalPump
At 18:32 I am getting an error "cannot knit sheets together", I have followed everything exactly and have double checked everything, what should I do?
please check your insert parameter
@@EngineerKoniagoI’m having the same problem idk where to see the insert parameters
hello sir, I have problem with lofted cut feature dont work and the message appear create intersecting geometry. how can fix it. Many Thanks for video's
take another look at the steps again.
maybe you click the wrong parameter
hi, I am getting an error while making loft command at 18.40 "cannot knit sheets together" do you have solutions
Maybe you need to check loft parameter..
@@EngineerKoniago i been following according to the video but i dont see any changes to the loft parameter. any suggestion?
@@Savier283 Open the sketch created at 16:00 and modify circle radius to 10mm and centerline length to 10 mm
@@alessandroscardi2210 thank u bro
I am also having this issue and tried the solution commented here and now it is saying intersecting geometry. Does anyone know how to fix these issues?@@kathickg9559
Why did you offset inlet from center
For make inlet cocentric with turbine Blade.
@@EngineerKoniago both inlet and turbine blade can be placed in centre,then why did you do offset
You could use shell instead of offset, would've save you minutes
thanks for advice
At 19:35 the circle in the front plane becomes smaller 19:36 than the initial 20mm. When I attempt the loft cut using the previous circle I get this error " Rebuild error: The feature couldn't be created because it would product self-intersecting geometry". I can send a screenshot so you help understand the precise problem. What are the changes you made so I can follow along.
please check again the selection points and the cut loft parameter
@@EngineerKoniago I am stuck at the same time point the lofted cut is not working at the given parameters. There was a skip in the video please explain
@@debabratadas9762 its different skecth, new sketch, offset entities, reverse 3mm.
Bang kenapa di menit 18.35, Ada notif " Rebuilds Errors, Cannot knit sheet together.
Mohon penjelasannya
How did u solve this problem bro please give information @mumachix
Hello, I think the turbine blades are in the wrong direction to push the water ^^
ruclips.net/video/_qubBlxAiH0/видео.htmlsi=9So1oYTWC8F33bI0
I fix the direction in this video.
I hope you like it...
@@EngineerKoniago yes thank you for the tutorial 👍
Parabéns!
Hi sir
Is there not impeller modeling?
To simulate this, i discover casing modeling. But haven't seen impeller
Great job
Thanks You
At 18:32 I increased the line length (in the vid it's 8 mm) to 25 mm, it stopped giving me the error
Hello, I am getting error at 18:32 the centerline parameters is giving rebuild error. Please guide me through it.
please check again what parameter your click
hello, what is the standard that you used in sizes of your volute casing? may I ask the source
hello, thank you for your videos, i want to do the simulation part in comsol instead of solidworks for my reasrch, if i tried to import this model in comsol will it works ??
(because i have made a pump's model from another software before but when i try to import it to comsol it shows me a warning)
hi.
maybe you can save as file into step or parasolid file. and you can inport the file into Solidworks
Please send us the solidwork file....
the loft part is not working for me...
even after checking the parameters.
can i send u the file and fix it for me?
What's your computer ?? CPU, RAM, Monitor Card ?
just a photato PC
Bang apakah ada settingannya, karna saya sudah mencobanya beberapa kali loftednya ttp tidak bisa 18:16 mohon penjelasannya bang🙏🙏
nggak ada settingan nya bang.
coba chek parameter yg di input nya dah bener apa blum.
Bang knpa di menit 18:38 ada notif " rebuild errors, cannot knit sheets together
Mohon penjelasannya bang
kemungkinan karna parameter nya ngaak support di knit bang coba di cek lagi titik2 parameter nya
@@EngineerKoniago cara ceknya gmna bang, soalnya saya sudah mengikuti seperti yg abang buat. Saya sudah mencoba mengulangnya hampir 10 kali, tetapi masalahnya sma saja.
@@EngineerKoniago atau saya blh dm abang tentang permasalahannya?
What is the material selected for this part
Casting bro
Sir geometry will be available?
Sure
@@EngineerKoniago thank you sir but Sir, how can I get the file?
@@EngineerKoniago sir plz send your mail
Sir can u give the sldpart plz I need it urgently
Please at 18:36 , I am getting the error message “ Cannot knit sheets together”
I will be really glad if you can help out
Thanks
please check parameter you insert
@@EngineerKoniago I clicked on the First circle and the base circle and used the curve as the centerline parameter
Is there a way I can send you a video to show you that exact place and how I did it?
why dont you center the propeler ?
hello i cannot knit the feature
hello sir, please chek the parameter again.
Di menit 3:05 kok gw ga ada option make pierce ya?
Coba chek lagi clik garisnya dah bener belum
give me planes ,please
Just Follow The Tutorial
Music is irritating
Not irritating it is very mesmerizing and relaxing❤
Bg kok eror nya menit 18:25 "cannot knit sheets together"
Mohon jelaskan bg soalnya ada tugas besar dan jelaskan pakai bahasa indo bg🙏
Perhatiin lagi parameter Loft nya bang.
Inggrisnya Aneh bang, Bahamas indo saja
Namanya juga lagi belajar bang wkwkwkw
@@EngineerKoniago bang, ini size nya darimana ya ? datasheet komponen yg abang punya ya ?