The 4 facet way specifically for those that can't grind drills by hand on a bench grinder......a very clever simple device that will make drill sharpening an easy task.
0:34 you need to do it with some feeling! In teh video one can see that the back of the drill is flipping upwards, this causes an error in sharpening the drill!
I think the reason for this small flip upwards, probably when the drill angle fixer/holder touches the drill slider, may be some slight angle misadjustment (the drill angle fixer/holder is by its 1 screw fixing over only may be 10mm not at an exact 90° angle to the drill axis, I guess this flip upwards will disappear when you flip the drill angle fixer by 180° because then a 91° angle causing a flip upwards should revert to a 89° causing a flip downwards which the drill is not doing, because downwards it is supported by the several sections drill slider over its total length). I think this flip upwards is small and will reduce the clearance angle only by a neglectable tiny bit. Expanding the drill angle fixer/holder to 2 or even 3 sections could eliminate this drill upwards flip, because over for example 50mm the deviation from 90° should be much less than over just 10mm. But such expanded drill angle fixer/holder will increase cost and makes handling more inconvenient and therefore the easiest way to tackle this inherent small weakness would be to apply sufficient push down force by your hand to avoid the flip upwards.
Hello Jose, you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html For further questions, please feel free to contact us under info@kaindl.de Best regards KAINDL-Team
kaindlde Hola, gracias por atenderme. El precio que me pone en la dirección que me indica me parece muy bueno, ya haré el pedido vía PayPal. Gracias de nuevo
See the drill moving as the operator makes it touch the wheel. The geometry is wrong for sharpening a twist drill.. This cannot result in a quality sharpening of the drill.
I think you are misunderstanding this movement. This movement is included to show, that BEFORE starting the grinding you have to adjust the cutting lip to be horizontal as exact as possible . In my view the geometry of this solution is quite smart (includes 180° flip over to grind the second lip and a V-grooved holder that support equal lenght grinding for both cutting lips/edges and a fine adjustment/end point for grinding to accommodate this) and using a flat diamond wheel avoids all the adjustment/angle change problems associated with the round front of a stone grinder. With a price of about 200 Euro this lowest cost solution by a professional in drill grinding (you can find much more expensive Kaindl solutions for professional drill grinding) may however be only of interest for rather wealthy hobbyists who want to have a clean solution giving them full control on both, point angle as well as especially the extremely important clearance angle at the cutting lips/edges. With the 825 attachment made by General (Taiwan) there do exist a much cheaper solution, but this does only give you control on the point angle while the clearance angle is NOT really under your control. At only 10% of the cost of the Kaindl solution many hobbyists may prefer a $25 drill holder/feeder only to a 200€ solution that includes also the holder for a flat diamond grinder wheel (or at higher cost even the diamond grinder wheel), as for most hobbyists the clearance angle on the 825 attachment seems to be OK in practice. The most cheap grinding solution however is grinding by your hand, which requires you to fully understand what you have to do/how you have to hold and move the drill on specific grinders and to have a good feeling in your hands in combination with good eyes and some help tools like a drill gauge to adjust the point angle and the length of cutting edges to be equal, while the clearance angle can only be roughly get right be looking at the chisel edge angle to roughly be/result in 135° when the clearance angle is roughly on target.
Hello Dante, you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html For further questions, please feel free to contact us under info@kaindl.de Best regards KAINDL-Team
Guten Tag Walter von der Vogelweide, vielen Dank für Ihren Kommentar. Anders als beim Kegelmantelschliff, wird hier auf der KSS ein 4-Flächenschliff auf Plan vorgenommen. Die Vor- und Zurückbewegungen sind hierbei essenziell notwendig, um den Bohrer zu schleifen. Wie in dem Video in 1:34 zu sehen ist, wird die Genauigkeit des Schleifergebnisses dadurch nicht beeinträchtigt. Mit freundlichen Grüßen Ihr KAINDL-Team
Это предварительная заточка т. е. грубая. Задняя часть не должна вымирать + тут нет подрезки середины сверла что даёт нагрузку на сверло - острие тупое,
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html For further questions, please feel free to contact us under info@kaindl.de Best regards KAINDL-Team
Сергей,этот станок стоит как подержаный автомобиль,немчура скромностью не отличалась.Пробовал найти алмазный диск,но таких нет.Выход один,колхозить что-то из советских или китайских,наши кулибины уже сделали подобные станки и по функционалу не хуже.
Wikipedia sagt: Die hohe Affinität des Eisens zum Kohlenstoff des Diamanten lässt nur in seltenen Fällen eine wirtschaftliche Bearbeitung von Stahl zu. Der Kohlenstoff aus dem Diamanten diffundiert mit zunehmender Temperatur in den Stahl, womit die Standzeit des Werkzeugs stark begrenzt ist. lasst euch nicht verarschen.. :D
Sehr geehrter Herr Hack, vielen Dank für Ihren Kommentar. Sie beziehen Ihre Information auf eine PKD-Beschichtung (Polykristalliner Diamant) wie in Wikipedia beschrieben. Unsere Diamant-Sichtschleifscheibe (Art. 10450) ist eine aus echtem Diamant belegte Sichtschleifscheibe. Es handelt sich nicht um eine künstliche hergestellte, CBN oder PKD-Belegung. Für weitere Fragen können Sie sich gerne unter der info@kaindl.de an uns wenden. Mit freundlichen Grüßen Ihr KAINDL-Team
kaindlde habt ihr überhaupt eine Ahnung von eurem Handwerk? Das ist allgemein eine Eigenschaft von Diamant! Und übrigens... CBN ist für das bearbeiten von HSS und andere stahlsorten geeignet.
Bei der Schärfung eines Bohrers kommt es meiner Meinung nach nicht in erster Linie auf wirtschaftliche Bearbeitung = möglichst hoher Abtrag an, sondern darauf, dass der Bohrer bezüglich Spitzenwinkel und Schneidewinkel sehr exakt und sauber geformt wird. Auf gar keinen Fall darf die Bohrerspitze überhitzt werden wie es bei wirtschaftlicher Bearbeitung wohl sofort der Fall wäre, denn Überhitzung (sichtbar an Verfärbung des Stahls) würde die Härte des Stahls reduzieren, der Bohrer wäre selbst bei bester Formgebung innerhalb kürzester Zeit wieder stumpf. Weil Überhitzung der Bohrerspitze vermieden werden muss kann man also doch eine nicht wirtschaftliche Bearbeitung per Diamantscheibe einsetzen zumal die Diamantscheibe ja den Riesenvorteil hat, dass sie mit ihrer seitlichen Belegung eine sehr glatte Schleiffläche zur Verfügung stellt, während die Front eines Schleifsteins immer rund ist, was die genaue Einstellung insbesondere des Schneidewinkels viel schwieriger gestaltet, wenn nicht praktisch sogar unmöglich macht. In alten US Bohrhilfen findet man aufgrund der Probleme mit der Rundheit der frontseitigen Schleiffläche bei Schleifsteinen manchmal die heute aus Sicherheitsaspekten nicht zulässige Schärfung von Bohrern an der Seite eines Schleifsteins gezeigt.
@@user-hk5qk8em3p ,это одна из лучших заточек сверла,есть повтор этой приспособы,по словам автора,отверстия после сверловки,соответствуют диаметру сверла!!!!))))))
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html For further questions, please feel free to contact us under info@kaindl.de Best regards KAINDL-Team
Mein Meister sagte: Wenn man sowas nicht von Hand ☝️ schleifen kann sollte man sich einen neuen Job suchen :D.* Außer bei den großen Bohrern ab 20mm, da ist so eine Vorrichtung Top.
Приспособа то хорошая, но недоделанная (ещё и дрель к ней нужна!), а за 16тыр я столько свёрл новых накуплю, что для неё уже и места не достанется!!!!!!!!!!
Ich schleife alle meine Bohrer seit 30 Jahren frei Hand. Gelernt ist gelernt.
Is this a 4-facetgrining. Looks like a easy way to get a complicated/good result.
I suppose this equippment can be bought?
A very good video.
das ist fantastisch.
A little bit sloppy, but the principal is one of the best I've seen. I shall make a more sturdy version myself.
Nice tool mr.
Хороший помощник. Молодцы немцы.
Даже при такой оснастке, сверло клюет при подаче, ( в первом этапе заточки ).
El mejor de todos.
👍👍👍👍👍👋👋👋👋👋
Wunderbar
Hola me compré esta máquina y va de lujo sobre todo la uso para afilar mis hojas circulares de sierra
A guarentee for exact angel? But the prize?
Danke schön!
Wow Amazing idea...
Very good..👍👍👍👍👍🆗
Super video
Donde puedo comprar la herramienta?
Какие градусы наклона направляющей площадки,относительно диска?БЛАГОДАРЮ.
Зависит от состояния точильщика , пиво-4,8 градуса , водка - 40 градусов 😂
muito bom aonde comprar?
DANKE!!!
Lucian Camargo Marmol can bhajan
me gustaria cuanto dinero cuesta y si es posible conseguirlo gracias
olá como adiquerir esta ferramenta e quanto ela custa
The 4 facet way specifically for those that can't grind drills by hand on a bench grinder......a very clever simple device that will make drill sharpening an easy task.
Muy bueno, donde se puede comprar? en Argentina
Amazing, thanks
0:34 you need to do it with some feeling! In teh video one can see that the back of the drill is flipping upwards, this causes an error in sharpening the drill!
I think the reason for this small flip upwards, probably when the drill angle fixer/holder touches the drill slider, may be some slight angle misadjustment (the drill angle fixer/holder is by its 1 screw fixing over only may be 10mm not at an exact 90° angle to the drill axis, I guess this flip upwards will disappear when you flip the drill angle fixer by 180° because then a 91° angle causing a flip upwards should revert to a 89° causing a flip downwards which the drill is not doing, because downwards it is supported by the several sections drill slider over its total length).
I think this flip upwards is small and will reduce the clearance angle only by a neglectable tiny bit. Expanding the drill angle fixer/holder to 2 or even 3 sections could eliminate this drill upwards flip, because over for example 50mm the deviation from 90° should be much less than over just 10mm. But such expanded drill angle fixer/holder will increase cost and makes handling more inconvenient and therefore the easiest way to tackle this inherent small weakness would be to apply sufficient push down force by your hand to avoid the flip upwards.
Happy new time ☺
This stuff is DIY?
Hallo, ich frage nuch wo ich das Albun Schärf den Mechanismus zun Schärfen des Bohrer, in Spanien. Danke
Hello Jose,
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html
For further questions, please feel free to contact us under info@kaindl.de
Best regards
KAINDL-Team
kaindlde Hola, gracias por atenderme. El precio que me pone en la dirección que me indica me parece muy bueno, ya haré el pedido vía PayPal. Gracias de nuevo
Very good idea
How much is the rate for that meachine???.
Please send us an e-mail with your request to g.woerz@kaindl.de
See the drill moving as the operator makes it touch the wheel. The geometry is wrong for sharpening a twist drill.. This cannot result in a quality sharpening of the drill.
No doubt, probably just a cheap solution for hobbyists and homeowners.
I think you are misunderstanding this movement. This movement is included to show, that BEFORE starting the grinding you have to adjust the cutting lip to be horizontal as exact as possible .
In my view the geometry of this solution is quite smart (includes 180° flip over to grind the second lip and a V-grooved holder that support equal lenght grinding for both cutting lips/edges and a fine adjustment/end point for grinding to accommodate this) and using a flat diamond wheel avoids all the adjustment/angle change problems associated with the round front of a stone grinder.
With a price of about 200 Euro this lowest cost solution by a professional in drill grinding (you can find much more expensive Kaindl solutions for professional drill grinding) may however be only of interest for rather wealthy hobbyists who want to have a clean solution giving them full control on both, point angle as well as especially the extremely important clearance angle at the cutting lips/edges.
With the 825 attachment made by General (Taiwan) there do exist a much cheaper solution, but this does only give you control on the point angle while the clearance angle is NOT really under your control. At only 10% of the cost of the Kaindl solution many hobbyists may prefer a $25 drill holder/feeder only to a 200€ solution that includes also the holder for a flat diamond grinder wheel (or at higher cost even the diamond grinder wheel), as for most hobbyists the clearance angle on the 825 attachment seems to be OK in practice. The most cheap grinding solution however is grinding by your hand, which requires you to fully understand what you have to do/how you have to hold and move the drill on specific grinders and to have a good feeling in your hands in combination with good eyes and some help tools like a drill gauge to adjust the point angle and the length of cutting edges to be equal, while the clearance angle can only be roughly get right be looking at the chisel edge angle to roughly be/result in 135° when the clearance angle is roughly on target.
Das ist gut.
Такая заточка сойдёт для дерева
Hola donde lo venden y cuanto sale. Gracias
Hello Dante,
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html
For further questions, please feel free to contact us under info@kaindl.de
Best regards
KAINDL-Team
und der Bohrer kippelt im Prisma, kann dann ja nicht besonders genau sein, etwas besser als mit Hand angeschliffen
Guten Tag Walter von der Vogelweide,
vielen Dank für Ihren Kommentar.
Anders als beim Kegelmantelschliff, wird hier auf der KSS ein 4-Flächenschliff auf Plan vorgenommen. Die Vor- und Zurückbewegungen sind hierbei essenziell notwendig, um den Bohrer zu schleifen.
Wie in dem Video in 1:34 zu sehen ist, wird die Genauigkeit des Schleifergebnisses dadurch nicht beeinträchtigt.
Mit freundlichen Grüßen
Ihr KAINDL-Team
Me gusta , afila fresas? Cuál es su costó?
www.kaindl.de/de/werkzeuge-tools/werkzeuge-schaerfen/kaindl-schaerf-station-kss.html
Вещь. Но я без этого научился точить..... За пол дня, и нех уже станка. Победители..... Епта....
Boa dia parece- me uma boa máquina aonde posso comprar em Portugal? Obrigado.
Please take a look: www.kaindl.de
Wenn man Bohrer schon nicht richtig schreiben kann, wie kann man dann eine gute Schleifvorrichtung bauen?
Это предварительная заточка т. е. грубая. Задняя часть не должна вымирать + тут нет подрезки середины сверла что даёт нагрузку на сверло - острие тупое,
Wo kann ich diesen Anhang hier in Mexiko bekommen?
Bộ đa may này ở đâu bán vậy shop
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html
For further questions, please feel free to contact us under info@kaindl.de
Best regards
KAINDL-Team
Як можна придбати такий станок?
Сергей,этот станок стоит как подержаный автомобиль,немчура скромностью не отличалась.Пробовал найти алмазный диск,но таких нет.Выход один,колхозить что-то из советских или китайских,наши кулибины уже сделали подобные станки и по функционалу не хуже.
@@user-eo2rr7jq6z один диск стоит больше 3000₽.
احسنت ستاذ 🌹🌹🌹👏👏👏👏💐💐💐👆👆👆💝💝💝💝👍👍👍👍💕💕💞💞🌺🌺🙋♂️🙋♂️🙋♂️🙋♂️
Wikipedia sagt: Die hohe Affinität des Eisens zum Kohlenstoff des Diamanten lässt nur in seltenen Fällen eine wirtschaftliche Bearbeitung von Stahl zu. Der Kohlenstoff aus dem Diamanten diffundiert mit zunehmender Temperatur in den Stahl, womit die Standzeit des Werkzeugs stark begrenzt ist.
lasst euch nicht verarschen.. :D
Sehr geehrter Herr Hack,
vielen Dank für Ihren Kommentar.
Sie beziehen Ihre Information auf eine PKD-Beschichtung (Polykristalliner Diamant) wie in Wikipedia beschrieben.
Unsere Diamant-Sichtschleifscheibe (Art. 10450) ist eine aus echtem Diamant belegte Sichtschleifscheibe. Es handelt sich nicht um eine künstliche hergestellte, CBN oder PKD-Belegung.
Für weitere Fragen können Sie sich gerne unter der info@kaindl.de an uns wenden.
Mit freundlichen Grüßen
Ihr KAINDL-Team
kaindlde habt ihr überhaupt eine Ahnung von eurem Handwerk? Das ist allgemein eine Eigenschaft von Diamant! Und übrigens... CBN ist für das bearbeiten von HSS und andere stahlsorten geeignet.
Bei der Schärfung eines Bohrers kommt es meiner Meinung nach nicht in erster Linie auf wirtschaftliche Bearbeitung = möglichst hoher Abtrag an, sondern darauf, dass der Bohrer bezüglich Spitzenwinkel und Schneidewinkel sehr exakt und sauber geformt wird. Auf gar keinen Fall darf die Bohrerspitze überhitzt werden wie es bei wirtschaftlicher Bearbeitung wohl sofort der Fall wäre, denn Überhitzung (sichtbar an Verfärbung des Stahls) würde die Härte des Stahls reduzieren, der Bohrer wäre selbst bei bester Formgebung innerhalb kürzester Zeit wieder stumpf.
Weil Überhitzung der Bohrerspitze vermieden werden muss kann man also doch eine nicht wirtschaftliche Bearbeitung per Diamantscheibe einsetzen zumal die Diamantscheibe ja den Riesenvorteil hat, dass sie mit ihrer seitlichen Belegung eine sehr glatte Schleiffläche zur Verfügung stellt, während die Front eines Schleifsteins immer rund ist, was die genaue Einstellung insbesondere des Schneidewinkels viel schwieriger gestaltet, wenn nicht praktisch sogar unmöglich macht. In alten US Bohrhilfen findet man aufgrund der Probleme mit der Rundheit der frontseitigen Schleiffläche bei Schleifsteinen manchmal die heute aus Sicherheitsaspekten nicht zulässige Schärfung von Bohrern an der Seite eines Schleifsteins gezeigt.
как говорится со знаменитой немецкой точностью не поспоришь
Хрень это а не заточка.
@@user-hk5qk8em3p ,это одна из лучших заточек сверла,есть повтор этой приспособы,по словам автора,отверстия после сверловки,соответствуют диаметру сверла!!!!))))))
Где купить такой?
Terima kasih
اداة سهلة وعملية
неплохо.
la quiero donde puedo comprar ayude
you will find more information at kaindl.de/en/werkzeuge-tools/werkzeuge-schaerfen-sharpening-tools/kaindl-schaerf-station-kss.html
For further questions, please feel free to contact us under info@kaindl.de
Best regards
KAINDL-Team
Not stable construction
Este foarte important să știi cum să ascuți nu numai un spiral .
Good 👍
Oki
With + english text running please n re upload herr. Danke
🧔👍💥
كم سعرالمنتج
Mein Meister sagte: Wenn man sowas nicht von Hand ☝️ schleifen kann sollte man sich einen neuen Job suchen :D.*
Außer bei den großen Bohrern ab 20mm, da ist so eine Vorrichtung Top.
presadora para tablero de puertas
EASY WITH HAND TO SHARP THE DRIL NO NEED OF ANY ATACHMENT
why can't you just use your hand, that would be much faster
Good
Wenn Sie einen Bohrer auf diese Weise zu schärfen , können Sie perfekt quadratische Löcher bohren!
good👍👍👍👍
in diesem Video wird richtig böse getrixt. Die Zustellungsabstände passen vom ersten zum zweiten Schliff überhaupt nicht.
Gia bal nhieu
fantastic complicated super torture
ok
Grazie per le
What?
Можно еще раз помедленнее и по русски?
Я записываю..
Учите, язык людей умной нации.
@@user-nz2jm6fy9j и кто умный
@@user-zj9et2yd4q
Нация.
@@user-nz2jm6fy9j скромно. так какая все таки? или что?
@@user-zj9et2yd4q
Пардон мадам, это информация не для средних умов, ваше сознание не выдержит.
Цена устройства
Ручками и глазками
Ein recht wackelige Vorrichtung.
Cheaper to buy new drill bits.
Куто задумано!
LOOOL
Haw can I get a small band saw?
Stukkend
Hand is much faster
рукожопная приспособа
Приспособа то хорошая, но недоделанная (ещё и дрель к ней нужна!), а за 16тыр я столько свёрл новых накуплю, что для неё уже и места не достанется!!!!!!!!!!
Дрель можно снимать и пользоваться отдельно.
Хорошая идея, при оборудовании наждака, вертикальная стойка. Надо будет подумать.
🧐😎👍
Idioma português
Mal afilada la broca!
Nachdem ich 10 amerikanische Dilettantenvideos gesehen habe... ahhh.
Dónde lo venden el aparato
The KSS can be found in our online shop:
www.kaindl.de/de/werkzeuge-tools/werkzeuge-schaerfen/kaindl-schaerf-station-kss.html
V
дасыс фантастиш)))
"фантастиш" - и коню понятно. А вот, над "дасыс" мне пришлось поламать голову, пока понял, что это - "das ist"
Заточка совершенно не годная, поэтому и сверлит плохо.
No entiendo ni madres ...!!!!!!!!!!!!!!!!!!!!!!!!!!
💕💕💕💕💕👏👏👏🌹🌹🤝🤝🤝🤝💖💖💖💖👆👆👆👆👆🌺🌺💝💝💝🌷🌷👍👍👍👍💐💐👋👋👋👋
this is really bad way how to sharpen a drill bit
Заточка хуёвенькая получилась,просверленное отверстие треугольное получилось.
А так идея не плохая.
da schleife ich meinen bohrer lieber selbst an xD und warum wurde beim rohr bohren das video geschnitten? schien ja doch nicht so richtig zu bohren xD
lol, ein geschärfter Bohrer sollte SO NICHT aussehen
Why not?
Marrakka Q FG t tttty
... und jetzt warten wir mal auf deine "Theorie", warum der (dieser) Schliff falsch ist.