Blazin' on second skin!!/s. Love the honesty. I wish the guys would recommend brands that they aren't distributers of - more often. Regardless this channel is insane with the amount of real info and sheer output of content.
Great job guys. If possible it would be nice to see more involvement/feedback before and after from customers like you’ve done in previous videos. Again, great job!!!
I just bought front infinity component speakers & the kicker key 200.4 for my ‘19 F150. Why didn’t you have the rear speakers on the for kicker key sound setup?
Question on the f150s and fast rings. Do you have to trim the middle ring ? Or they fit into place without interference ? And just trim the plug and the outer ring... (18 F150)
This is going to be my next career... I've always loved to do installs. Back in the 90's it wasn't so complicated... Is there a school for car audio and fabrication?
Impressive!! Know where i can get some 6x9 speaker brackets for 2015 altima. Ive checked everywhere and can't find any. Everyone says they just drop right in, but they dont
Next time you guys get a f150 in, could you use your signal thingymagigy to test and see if the signal going to the tweeters is high pass or full range please? I'm thinking of replacing the tweeter with 3.5 inch coxial speaker but idk if the signal from the radio is only for the tweeter.
You're a really good installer and know what you're doing. So it's kind of sad to hear you go off about the fast rings being so wrong. That foam is almost entirely acoustically transparent. It will offer some mild attenuation and diffusing for higher frequency sound, but it will in no way do what you describe or what the maker claims. This is mostly due to the low mass open cell foam they are using. The concept is 100% accurate, but the material they are using is not proper. The reason the manufacturer uses that foam is to stop rattling of the parts against one another, not to "enhance bass". Bass frequencies won't even notice that material. Even if it was closed cell higher density foam that would actually perform like you are saying, low frequencies will completely ignore it. There is a reason why "Bass Traps" are huge heavy behemoths. They need to be. A little piece of lightweight open cell foam stuck to your door isn't going to do a single thing for your bottom end. Please, take some time to read up on acoustic treatment and stop selling this snake oil to your customers.
The way I understand it is the round speakers produce a more accurate sound compared to the oval speakers. Yes you can get more volume with larger cone area but I don't thing the quality is there.
I’m in the process of sound dampening my 2003 F-150 and my god it sucks. I’m doing the inside of the doors and it’s so hard for me to reach. Your arms and hands get torn up doing that. The holes are only half the size then this truck in your video. I had to cut the sheets in half just to fit.. Very time consuming.
I forgot which car audio RUclipsr has a video on a quick way. Just like everything prep is the most important part. If you don't clean the surface it is possible for the deadener to fall off.
dj kritical I did all that. I’m not worried about it coming off. It just was horrible to have your hands bent like that to get in there. My truck did not have large openings they were small in the doors. But it’s done now and is worth it
Always love the fact that you guys are using the factory locations and keeping the stock look. I HATE the trend nowdays where everyone is making speaker pods for the pillars. It looks cheap and tacky.
that tweeter install was absolute artwork.
I love that fabrication of the tweeter mount. We need more installers like you and Fernando here in Hawaii.
Blazin' on second skin!!/s. Love the honesty. I wish the guys would recommend brands that they aren't distributers of - more often. Regardless this channel is insane with the amount of real info and sheer output of content.
The amount of effort put into every step of the process.. I’m totally blown away
Thanks again for taking the time and showing us your beautiful work!
Great job guys. If possible it would be nice to see more involvement/feedback before and after from customers like you’ve done in previous videos. Again, great job!!!
I dig it. Itd be more like a high production show on discovery. Still Awesome production tho, deano.
Always a good show.
You guys rock.
I would live to see a full video install on a JL Wrangler. Can you do a video?
Do you sell those morel acrylic tweeter pieces also? Looking at these same speakers for a 2015 Ford F150 crew
Test the fast ring In the door and trim one and use it as a a guide to trim the other door its not so much of a pain to cut when it's not on the door
Are you going to get the New floating screens from Kenwood and pioneer?
I just bought front infinity component speakers & the kicker key 200.4 for my ‘19 F150. Why didn’t you have the rear speakers on the for kicker key sound setup?
Do you want to use the whole piece of fast ringon for the inside piece? Instructions say trim to .5" wonder what sounds better
Very nice professors
Question on the f150s and fast rings. Do you have to trim the middle ring ? Or they fit into place without interference ? And just trim the plug and the outer ring... (18 F150)
This is going to be my next career... I've always loved to do installs. Back in the 90's it wasn't so complicated... Is there a school for car audio and fabrication?
How do these Morels compare to the Rockford power series, Jl C2 series, etc.
Rockford speakers suck
It'll be the back police dean!! Lol
Any risk with the passenger airbag when running the wire to the tweeter or is the wire fished behind the airbag?
Impressive!! Know where i can get some 6x9 speaker brackets for 2015 altima. Ive checked everywhere and can't find any. Everyone says they just drop right in, but they dont
Crutchfield!!!
@@tatialo37 I tried there too, but im not coming up with anything at all
Next time you guys get a f150 in, could you use your signal thingymagigy to test and see if the signal going to the tweeters is high pass or full range please? I'm thinking of replacing the tweeter with 3.5 inch coxial speaker but idk if the signal from the radio is only for the tweeter.
Do you recommend the speaker baffle ?? Have you install them before ??? Hope you guys answer :(
Why is it so hard to find speaker adapters for a Ford Figo Trend 2014 model ?
Which would rather have a 6.5 or 6x9.
I went with 6X9 on the front doors of my Silverado, Pioneer TS D69C for better mid-bass.
Can this install work with the B&O system on the f150?
Is the morel components better than infinity , avatar and dd-redline?
Depends what model
Are morel speakers sord of high end?
have you guys done any 15+ f150 with extended cab?
ruclips.net/video/CiVSjUuPn3A/видео.html
You're a really good installer and know what you're doing. So it's kind of sad to hear you go off about the fast rings being so wrong. That foam is almost entirely acoustically transparent. It will offer some mild attenuation and diffusing for higher frequency sound, but it will in no way do what you describe or what the maker claims. This is mostly due to the low mass open cell foam they are using.
The concept is 100% accurate, but the material they are using is not proper. The reason the manufacturer uses that foam is to stop rattling of the parts against one another, not to "enhance bass". Bass frequencies won't even notice that material. Even if it was closed cell higher density foam that would actually perform like you are saying, low frequencies will completely ignore it. There is a reason why "Bass Traps" are huge heavy behemoths. They need to be. A little piece of lightweight open cell foam stuck to your door isn't going to do a single thing for your bottom end.
Please, take some time to read up on acoustic treatment and stop selling this snake oil to your customers.
Has anyone been able to do bypass on pioneer dmh-w4660nex ? Video cuts off after going 10mph.
Tomorrow
I'm never going to understand replacing 6X9s with smaller speakers. It seems sacrificial to me even if a subwoofer will be used.
The way I understand it is the round speakers produce a more accurate sound compared to the oval speakers. Yes you can get more volume with larger cone area but I don't thing the quality is there.
Cheap 6/9, expensive 6.5!!!
@@DevinderAthwal306 Kicker Solo-Baric claim otherwise.
I’m in the process of sound dampening my 2003 F-150 and my god it sucks. I’m doing the inside of the doors and it’s so hard for me to reach. Your arms and hands get torn up doing that. The holes are only half the size then this truck in your video. I had to cut the sheets in half just to fit.. Very time consuming.
I forgot which car audio RUclipsr has a video on a quick way. Just like everything prep is the most important part. If you don't clean the surface it is possible for the deadener to fall off.
dj kritical I did all that. I’m not worried about it coming off. It just was horrible to have your hands bent like that to get in there. My truck did not have large openings they were small in the doors. But it’s done now and is worth it
Cool!!!
Always love the fact that you guys are using the factory locations and keeping the stock look. I HATE the trend nowdays where everyone is making speaker pods for the pillars. It looks cheap and tacky.
Marriage is not a verb.
Soundskins Rings are way better than Stinger, though.