Adam you deliver practical, useful information that costs nothing to receive and for anyone to whine about your intro I'm not sure where they'd go to find it but I wish they would. Please keep the wisdom flowing, you are an amazing EUC resource keeping us all safe and informed. 6 pac Gord
Couple of things to note/correct: Lynx does balancing at lower voltage also. It uses different bms ic than all other previous leaperkim wheels. That ic is what enables smart bms features and also controls balancing mosfets that bleed voltage using resistors. I couldn't find exact ic just from pictures or battery test pdf, so I don't know exact conditions for balancing to happen(is only in charging or is it always when voltage difference is too high). But I can confirm that it works, I have set charger to 4.15v/cell for more than 20 cycles. And smart bms shows at max 0.017v voltage difference between cells. Also I wouldn't recommend 22A charging on sherman S. Manufacturer states maximum charging rate to be 15A. I have fried bms in sherman s, and wheel has been disassembled for more that half year due to slow communication from manufacturer. It broke while not in charger, but I have used 20a charger on it before that. It should not affect anything since Bms uses exactly same port for wheel use and charger. You'd get a lot more charging current with hard braking than with charger. But you'll never know.. investigation is still ongoing. Also please refrain from talking about politics. World events are much more complicated that we make them to be..
One thing to note: being a coward isn’t the right way to live. If you can’t face or understand a simple matter you shouldn’t be riding an electric vehicle mate, you might hurt yourself 🇵🇸
Adam the voltage on the display menu is a cosmetic value, it can also be miscalibrated (sometimes by a whole volt), you have to check the value of the BMS with the APP which is correct and then calibrate the display value according to that. Also you don't have to think about riding only to 20%, that is for individual cells, wheel only lets you ride to about 3.14V per cell before tiltback (113V) unless you enable low battery mode.
Great info... much of the info your provided applies to any wheel (the various settings and the theory behind the settings, info about charging and battery life, suspension setup, etc.). So I found many useful tips that I haven't been able to find elsewhere (I don't have the Veteran). So once again., awesome video and you rock 🥰
NOTE:: 23:48 Adam, leaving High-Speed mode on, will drain your battery faster even at normal speeds. Here's the relevant quote: "Torque is proportional to field flux * current. So field weakening will cause an increase in current to maintain torque." Google "Using field weakening to increase max speed of an EUC?" for the source article with links to physics papers on this
You should read your own sources: Field weakening activates and uses more current at higher RPM's not at lower RPM's, the whole point of using field weakening is to increase RPM.
Then why it is off by default? FW has a cost of increasing current, more current means more heat, motor and controller and all the wiring runs hotter at higher current
If you want to save your setting change faster you can just hold the ok button again to exit settings mode. That works on the Patton at least. Also when changing the numbered values, you tap the ok button to go up as seen here, but you can also short longpress the ok button (about 1-1.5 second press) to go down.
@@mr_wrongway No problem, thanks for the great video, I'm gonna have to go update my Patton now so I can get the button volume control, because that beep on turning off is SO LOUD.
People keep characterizing the 100% charge issue as a problem on hills. I'm having the 100% charge issue on streets with a downward slope, not terrain the anyone would consider a hill. Thx for the video.
Hey! love the videos man. I am thinking of getting my first EUC. I watched your Top 6 Beginner EUC video, but I gotta say. I am not completely convinced. I do get they are slower/more comfortable wheels but I want something I can invest a lot of time in and really push to it's limit, eventho it might be harder for a beginner. I would like to be able to reach a speed of around 80km/h (more doesnt matter of course, since one can always drive slower). I dont plan on driving that fast, but I would like to be able to, if I change my mind in the future. I plan on using it more on regular streets, so the tire should be more on that side, but I would also like to casually drive around the forest or more "off-road" terrain and maybe do some jumps in the future. Is there a good hybrid wheel thats capable of both but leans more on the "road-side" of things? I would also like something with suspension. I heard the Begode Master V4 and EX30 is really good and they also cost under 3 k on sale. Any help would be highly appreaciated. 🙂
WW. Great content! Have you tried using snowboard/ski boots? They have a stiff upper that allows you to leverage the heel/toe pressure by simply moving your hips forward and back. I’ve used snowboard boots on my wheel. (I don’t use power pads) It feels different but there’s definitely more control for acceleration/braking. I don’t have to use as much upper body. I think it strengthens the interface between rider and wheel. You have a lot of experience and skill and more than one device, so I value your opinion. If you can, try it. If you think there’s potential for it, give me a reply. Thnx.
Hi Adam. Today I rode my new Lynx and found that the speed reading is a little higher than the GPS speed. Do you happen to know how to calibrate the speed reading?> Would be great to know. Thanks.
Hello Adam, my lynx is brand new but it seems that my compression damper makes no difference whatever I do to it. Rebound however is noticeacle ... I don't know if it's normal for the compression to make very little to no difference...
There’s a setting in a menu you left out on this video, one that’s in the lynx instruction book, has to do with cell balancing. But as per usual, the instructions for it are vague. If you look a page 3.2 and 3.3 there’s a mention “set running background time to perform battery balancing” and there’s a button press procedure to get to that setting. Anyone have any idea of what that is all about. Is there a balancing function on the wheel itself?
Bonjour Adam, merci pour cette excellente vidéo ! Serais-tu me recommander une viscosité pour le remplacement de l’huile de suspension présent dans ma Patton 66 pour une utilisation standard mix entre route et chemin souvent autour de 50km/h ? Merci pour ton aide 😊✌️
So i just got my Lynx today and my last wheel was an MSP. I have several thousand miles on the MSP but the Lynx makes me feel like i know nothing. Turns are either hard or just too wobbly. Feel like i have to relearn to ride entirely. Currently using 65% Ride mode but if anyone has advice on making it less unstable in turns i would appreciate it. It may just be that I have to get used to the weight increase of this new wheel
Apparently some people don't have the option of fast-forwarding on their device 🙄 You are guests here on his channel and I think he can talk about whatever he wants. After all, there's more to life than EUCs. He can also decide for himself what to do with his hair 🙄 Anyway, thank you for this video. Nicely shown and explained 😊
Don’t care about war or your politics. I watch EUC content you escape worldly issues for a moment and just want to be entertained. I’m only interested in your opinions on EUC’s not your politics.
Talking about politics, no matter how much you believe it yourself, is harmful to each creator. I agree, I come here to listen about technology, to take a break from the rest of things in the world. Not to listen about politics
No, compression means how the suspension behaves when it compresses, preload means that the spring is preloaded and will sag less when you step on the wheel
Please don't take this the wrong way. But please leave out the politics. We are here for EUC content. Make a new politics channel, by all means promote it. I have a general idea about the topic and have no real interest in learning more. You are a skilled rider and I enjoy watching so I want to see your channel grow but this is not the play.
How entitled must you be to tell someone how they should run their channel and what topics they should discuss? 🤔 "I have a general idea about the topic and have no real interest in learning more." Said the human ostrich as they buried their head in sand, unaware that real ostriches do no such thing.
@@space.youtube what is your deal? im giving constructive criticism, he is free to do what he wants to. the bigger picture is it will drive people away from the channel. im not wrong either, just look at how many people echo what im saying.
I don't have stake in the matter, I am south American. But I think any genuine discussion about suffering or civilians should start by. I feel sorry for the 1000s of people that Palestinian terrorist killed in October past year, some of them burn in the their own houses, and all the still kidnapped in Gaza, followed by the victims of the Israeli RESPONSE. the fact you mention one and don't mentioned the other makes your unfair and bias. everyone should try to remain unbiased. in the case of Ukraine, the is no argument there. Russia should leave Ukraine.
You're either brain washed, or a random pro israeli talking point generator. History didn't begin on the 7th of October, but lets pretend it did for the purposes of this discussion. Does anything that happened on the 7th justify what has happened since? You either value life, or you don't. You either believe people are equal, or you don't. You either oppose the senseless, unnecessary slaughter of innocent civilians, or you do don't. You either believe in justice, or you don't. You either know the difference between justice and indiscriminate retribution, or you don't. If you don't, then what happened on the 7th is ok, and you have no reason to complain about it. If you do, then you'd want those who committed the atrocities to be punished, and the collective punishment of every Palestinian in Gaza, regardless of whether they were involved or not to stop. I know these things, Mr Wrongway seems to, why don't you? 🤔 There is no "both sidesing" what is happening in Gaza.
I love your videos, but we are here only to learn about EUCs, not about politics. It is sad to see how universities in USA are being destroyed by radicals.
Not as sad as how democracy is being destroyed by establishment propaganda and wilfully ignorant people who uncritically believe the narrative they're spoon fed.
I don't get it not every RUclips channel has to become a whole politic channel if I want politics I'll freaking go to Fox News I don't need you to say it here thank you
I'd suggest you refrain from bringing politics into your videos, I'll start losing more respect for you than I already have.. I'd prefer to continue being a subscriber of yours😬
💯 why would I take advice from some random guy who reviews electric unicycles it's not like he's some politician just some random dude with purple hair who likes watermelon
Regarding the "increasing prorests" in the United States, for example, the 300 protesters arrested at Columbia University do not speak for the other 20,000,000 people that live in the New York City metro area. Just like the rest of America, about .0015 of 1% percent of the population are protesting on behalf of Hamas, Iran, and Gaza
thumbs down from me today as I tune into our channel for euc content and not political commentary. I lost interest as soon as you start telling me how to think about world issues. start a separate channel for this type of thing
Well. I unsubbed awhile ago because if I wanted the political update I'll seek it out on my own. Just wanted the EUC stuff. I'll never make this mistake again, farewell wrongway.
Free Palestine 🇵🇸 you OG bro, best way to find the cowards among us is looking at the comments section. It bothers them so much that they can’t just ignore it. We are taking it back🇵🇸
Great video, really informative. It's a resource to all Lynx owners, both current ant future. And much respect for not being afraid to speak your mind. #FreePalestine #CeasefireNow #BDS
@@mr_wrongwaybro this war is turning everybody into 2 year olds we are not in 5th grade just review the unicycles and nobody gives a damn about your political views you're not Fox News
Ah, the classic mix-up between Chanel and channel-always a delight in text debates! It's rather amusing how a single typo can lead to such a fragrant confusion. Speaking of which, it appears a few punctuation marks missed their stop along your grammar train-quite the runaway sentence, wouldn't you say? If you're doling out style advice, perhaps consider investing in a few commas and periods; they truly complete any ensemble. And while we're shopping, might I suggest a dash of humor? It's the one accessory that never goes out of style!
Technical aspects of this video are excellent. Thank you for your time and commitment to the technical issues.
Adam you deliver practical, useful information that costs nothing to receive and for anyone to whine about your intro I'm not sure where they'd go to find it but I wish they would. Please keep the wisdom flowing, you are an amazing EUC resource keeping us all safe and informed. 6 pac Gord
The best EUC ever made
Yep
Couple of things to note/correct:
Lynx does balancing at lower voltage also. It uses different bms ic than all other previous leaperkim wheels. That ic is what enables smart bms features and also controls balancing mosfets that bleed voltage using resistors.
I couldn't find exact ic just from pictures or battery test pdf, so I don't know exact conditions for balancing to happen(is only in charging or is it always when voltage difference is too high).
But I can confirm that it works, I have set charger to 4.15v/cell for more than 20 cycles. And smart bms shows at max 0.017v voltage difference between cells.
Also I wouldn't recommend 22A charging on sherman S.
Manufacturer states maximum charging rate to be 15A.
I have fried bms in sherman s, and wheel has been disassembled for more that half year due to slow communication from manufacturer.
It broke while not in charger, but I have used 20a charger on it before that.
It should not affect anything since Bms uses exactly same port for wheel use and charger. You'd get a lot more charging current with hard braking than with charger. But you'll never know.. investigation is still ongoing.
Also please refrain from talking about politics. World events are much more complicated that we make them to be..
One thing to note: being a coward isn’t the right way to live. If you can’t face or understand a simple matter you shouldn’t be riding an electric vehicle mate, you might hurt yourself 🇵🇸
@@matincdk6965 wtf are you on about?
Adam the voltage on the display menu is a cosmetic value, it can also be miscalibrated (sometimes by a whole volt), you have to check the value of the BMS with the APP which is correct and then calibrate the display value according to that. Also you don't have to think about riding only to 20%, that is for individual cells, wheel only lets you ride to about 3.14V per cell before tiltback (113V) unless you enable low battery mode.
Great info... much of the info your provided applies to any wheel (the various settings and the theory behind the settings, info about charging and battery life, suspension setup, etc.). So I found many useful tips that I haven't been able to find elsewhere (I don't have the Veteran).
So once again., awesome video and you rock 🥰
Looking forward to your final review of this wheel.
NOTE:: 23:48 Adam, leaving High-Speed mode on, will drain your battery faster even at normal speeds. Here's the relevant quote: "Torque is proportional to field flux * current. So field weakening will cause an increase in current to maintain torque." Google "Using field weakening to increase max speed of an EUC?" for the source article with links to physics papers on this
You should read your own sources: Field weakening activates and uses more current at higher RPM's not at lower RPM's, the whole point of using field weakening is to increase RPM.
Then why it is off by default? FW has a cost of increasing current, more current means more heat, motor and controller and all the wiring runs hotter at higher current
@@Alejandro388 it draws more current at high speeds only
If you want to save your setting change faster you can just hold the ok button again to exit settings mode. That works on the Patton at least. Also when changing the numbered values, you tap the ok button to go up as seen here, but you can also short longpress the ok button (about 1-1.5 second press) to go down.
Thanks for the insights!
@@mr_wrongway No problem, thanks for the great video, I'm gonna have to go update my Patton now so I can get the button volume control, because that beep on turning off is SO LOUD.
Great video, thanks alot, it helps a bunch , and im using your code to get the charger 👍
Thank you for touching in on the conflict, truly a horrible situation....😟
People keep characterizing the 100% charge issue as a problem on hills. I'm having the 100% charge issue on streets with a downward slope, not terrain the anyone would consider a hill.
Thx for the video.
Hey! love the videos man. I am thinking of getting my first EUC. I watched your Top 6 Beginner EUC video, but I gotta say. I am not completely convinced. I do get they are slower/more comfortable wheels but I want something I can invest a lot of time in and really push to it's limit, eventho it might be harder for a beginner. I would like to be able to reach a speed of around 80km/h (more doesnt matter of course, since one can always drive slower). I dont plan on driving that fast, but I would like to be able to, if I change my mind in the future. I plan on using it more on regular streets, so the tire should be more on that side, but I would also like to casually drive around the forest or more "off-road" terrain and maybe do some jumps in the future. Is there a good hybrid wheel thats capable of both but leans more on the "road-side" of things? I would also like something with suspension. I heard the Begode Master V4 and EX30 is really good and they also cost under 3 k on sale. Any help would be highly appreaciated. 🙂
This is a great video with a lot of useful information. And I got my Lynx only 6 days ago 😂
Wheee!
My Lynx came with small rubber pieces and a buzzer that I don't know what to do with. The Lynx rocks!
It’s a spare fuse and beeper in case you need them.
Hello Adam thank you for All of your work. If you have to choose beetween patton and V14 which would your choose ?
I am so glad you are talking about this❤
WW. Great content!
Have you tried using snowboard/ski boots?
They have a stiff upper that allows you to leverage the heel/toe pressure by simply moving your hips forward and back.
I’ve used snowboard boots on my wheel. (I don’t use power pads)
It feels different but there’s definitely more control for acceleration/braking.
I don’t have to use as much upper body.
I think it strengthens the interface between rider and wheel.
You have a lot of experience and skill and more than one device, so I value your opinion.
If you can, try it.
If you think there’s potential for it, give me a reply.
Thnx.
Thank you greatly appreciated
How to set up for the Sherman L.
The ride mode, and do the high speed mode Press on always or not? And the acceleration Asisdent set up to 15 or 20?
Hi Adam. Today I rode my new Lynx and found that the speed reading is a little higher than the GPS speed. Do you happen to know how to calibrate the speed reading?> Would be great to know. Thanks.
Hello Adam, my lynx is brand new but it seems that my compression damper makes no difference whatever I do to it. Rebound however is noticeacle ... I don't know if it's normal for the compression to make very little to no difference...
No politics please, we dont need propaganda but information. Thanks
What about the 2 silver screws on each shock? I can't seem to find any info on what to do with those
Using a CE200 to measure voltage, my charger stock was running 152.6v before I reset it back to 151.2-3
There’s a setting in a menu you left out on this video, one that’s in the lynx instruction book, has to do with cell balancing. But as per usual, the instructions for it are vague. If you look a page 3.2 and 3.3 there’s a mention “set running background time to perform battery balancing” and there’s a button press procedure to get to that setting. Anyone have any idea of what that is all about. Is there a balancing function on the wheel itself?
I subscribed because of your support for Palestine ... great video brother
Cheers mate!
Bonjour Adam, merci pour cette excellente vidéo !
Serais-tu me recommander une viscosité pour le remplacement de l’huile de suspension présent dans ma Patton 66 pour une utilisation standard mix entre route et chemin souvent autour de 50km/h ?
Merci pour ton aide 😊✌️
Hello! You’re welcome :) I don’t know actually … please ask on forums!
Was tried Shinko 241 at 32 psi.. almost killed myself how unstable it was, but at 26psi its start to shine. So psi depends much on tire thread
What is on your head?
Haha bro lost it
It’s hair
Will cells ballance when we full charge even if we lowered the output woltage inside the charger on that tiny knob?
On the Lynx it should be balanced, on older Veteran wheels it should balance at full voltage (not overvoltage)
So i just got my Lynx today and my last wheel was an MSP. I have several thousand miles on the MSP but the Lynx makes me feel like i know nothing. Turns are either hard or just too wobbly. Feel like i have to relearn to ride entirely.
Currently using 65% Ride mode but if anyone has advice on making it less unstable in turns i would appreciate it. It may just be that I have to get used to the weight increase of this new wheel
Apparently some people don't have the option of fast-forwarding on their device 🙄
You are guests here on his channel and I think he can talk about whatever he wants. After all, there's more to life than EUCs. He can also decide for himself what to do with his hair 🙄
Anyway, thank you for this video. Nicely shown and explained 😊
Is there difference in torque if you are on High speed Off/On?
I never noticed any. Probably at high speed there is a difference :)
Don’t care about war or your politics. I watch EUC content you escape worldly issues for a moment and just want to be entertained. I’m only interested in your opinions on EUC’s not your politics.
Talking about politics, no matter how much you believe it yourself, is harmful to each creator.
I agree, I come here to listen about technology, to take a break from the rest of things in the world. Not to listen about politics
The subject is too important not to be mentioned 🇵🇸🍉
@@mr_wrongway your purple hair alone expresses where you lie politically. No need to verbalize it.
@dustinhankins2153 he changed a lot through the years for the worst. That is very sad
Some subjects we can afford to ignore, but shouldn’t. He has his platform and is using it the way he feels is right.
Can you get the full 15 amps from plugging in the wall in the usa?
He isnt in the USA so I dont think he knows that answer.
It depends on the outlet. In the EU you can usually pull up to 3 kW from the wall plug.
why do i have no number mesurements on my lynx app? i can change the settings but i see no numbers just the line 😮
Weird!
I also don't see the numbers in the application
Same here. Maybe this happens on certain phones
Isn’t compression and preload the same thing?
No, compression means how the suspension behaves when it compresses, preload means that the spring is preloaded and will sag less when you step on the wheel
Pidzoom - sends to Poland?
I think they do!
What happened to your seat? Is that just dirt on it?
Yeah the mudguard is too short and the mud sprays onto the seat when it’s wet
@@mr_wrongway Ah ok I have one coming in next week..
Are you happy with it? Comfort wise and practicality?
Please don't take this the wrong way. But please leave out the politics. We are here for EUC content. Make a new politics channel, by all means promote it. I have a general idea about the topic and have no real interest in learning more.
You are a skilled rider and I enjoy watching so I want to see your channel grow but this is not the play.
How entitled must you be to tell someone how they should run their channel and what topics they should discuss? 🤔
"I have a general idea about the topic and have no real interest in learning more."
Said the human ostrich as they buried their head in sand, unaware that real ostriches do no such thing.
@@space.youtube what is your deal? im giving constructive criticism, he is free to do what he wants to. the bigger picture is it will drive people away from the channel. im not wrong either, just look at how many people echo what im saying.
@@levelfift33n See previous comment.
please don't take this the WROOONNNG WAY!!!
I don't have stake in the matter, I am south American. But I think any genuine discussion about suffering or civilians should start by. I feel sorry for the 1000s of people that Palestinian terrorist killed in October past year, some of them burn in the their own houses, and all the still kidnapped in Gaza, followed by the victims of the Israeli RESPONSE. the fact you mention one and don't mentioned the other makes your unfair and bias. everyone should try to remain unbiased. in the case of Ukraine, the is no argument there. Russia should leave Ukraine.
It doesn’t compare, you can’t pay any attention to the oppressor, unless you have a frame of hitler hanging at your house mate, do you? Free 🇵🇸
Taking people's homes and forcing them into an open air prison tends to create extremists.
You're either brain washed, or a random pro israeli talking point generator. History didn't begin on the 7th of October, but lets pretend it did for the purposes of this discussion.
Does anything that happened on the 7th justify what has happened since?
You either value life, or you don't.
You either believe people are equal, or you don't.
You either oppose the senseless, unnecessary slaughter of innocent civilians, or you do don't.
You either believe in justice, or you don't.
You either know the difference between justice and indiscriminate retribution, or you don't.
If you don't, then what happened on the 7th is ok, and you have no reason to complain about it. If you do, then you'd want those who committed the atrocities to be punished, and the collective punishment of every Palestinian in Gaza, regardless of whether they were involved or not to stop.
I know these things, Mr Wrongway seems to, why don't you? 🤔
There is no "both sidesing" what is happening in Gaza.
This did not start October last year, this started 75 years ago, you have to start from the beginning, you are on the wrong side of history
The apartheid started 75 years ago. Stop being a fascist
I love your videos, but we are here only to learn about EUCs, not about politics. It is sad to see how universities in USA are being destroyed by radicals.
It is sad to see you not being intellectually capable of supporting what’s right or being an ignorant imbecile. Either way mate free 🇵🇸
Not as sad as how democracy is being destroyed by establishment propaganda and wilfully ignorant people who uncritically believe the narrative they're spoon fed.
Yes FREE Palestine, thank you for recognise what’s going on in the world.
Yeah free Palestine, because they are so peaceful and friendly to their neighbours :D
People seem to forget October the 7th.
@@skampster people seem to forget a lot more...
I don't get it not every RUclips channel has to become a whole politic channel if I want politics I'll freaking go to Fox News I don't need you to say it here thank you
I'd suggest you refrain from bringing politics into your videos, I'll start losing more respect for you than I already have.. I'd prefer to continue being a subscriber of yours😬
October 7th will never be forgotten, don't do this to yourself 👀
WILL NOT BE TAKING AN ADVICE FROM A DUDE WITH PINK HAIR .
💯 why would I take advice from some random guy who reviews electric unicycles it's not like he's some politician just some random dude with purple hair who likes watermelon
Regarding the "increasing prorests" in the United States, for example, the 300 protesters arrested at Columbia University do not speak for the other 20,000,000 people that live in the New York City metro area. Just like the rest of America, about .0015 of 1% percent of the population are protesting on behalf of Hamas, Iran, and Gaza
You statistics are as good as your profile picture mate, filled with words you can’t properly comprehend. Stick to your balls yeah? Free 🇵🇸
thumbs down from me today as I tune into our channel for euc content and not political commentary. I lost interest as soon as you start telling me how to think about world issues. start a separate channel for this type of thing
Veteran fix your damn pwm reported to apps ffs
Free free Palestine 🇵🇸
Well. I unsubbed awhile ago because if I wanted the political update I'll seek it out on my own. Just wanted the EUC stuff. I'll never make this mistake again, farewell wrongway.
Mr dirt surfer. Let's all agree. China is the country we should support. Chinese EUC's for the win!
Free Palestine 🇵🇸 you OG bro, best way to find the cowards among us is looking at the comments section. It bothers them so much that they can’t just ignore it. We are taking it back🇵🇸
How's the watermelon😂
bye bye
Going to unsubscribe if this political nonsense continues from an increasingly woke creator.
Great, have fun blasting disaster on your couch mate! 🇵🇸
Goof@@matincdk6965
Continue sleeping 💁♂
If you want to ride a one wheeled vehicle, accept some one sided narratives, wildman. Don't get soft on me
Great video, really informative. It's a resource to all Lynx owners, both current ant future.
And much respect for not being afraid to speak your mind.
#FreePalestine
#CeasefireNow
#BDS
Bot
Bot
@@joeyfaze2088 It's like you have no sense of irony 🤣
@@space.youtube BOT!
Please done ruin your Channel
I don’t use Chanel
My man ran out of brain cells, Israel took a number of this one! Keep it to yourself mate
@@mr_wrongwaybro this war is turning everybody into 2 year olds we are not in 5th grade just review the unicycles and nobody gives a damn about your political views you're not Fox News
You edited your comment and still couldn't structure a correct sentence 🤡
Ah, the classic mix-up between Chanel and channel-always a delight in text debates! It's rather amusing how a single typo can lead to such a fragrant confusion. Speaking of which, it appears a few punctuation marks missed their stop along your grammar train-quite the runaway sentence, wouldn't you say? If you're doling out style advice, perhaps consider investing in a few commas and periods; they truly complete any ensemble. And while we're shopping, might I suggest a dash of humor? It's the one accessory that never goes out of style!
FREE PALESTINE!! 🍉🍉🍉🍉
Ok nobody gives
It's a freaking electric unicycle channel not Fox News
Lol
ALL THIS stuff over price LOL LOL
China didn't let "rainbow flag western riders" ride a euc for straights!😮