Oh it’s definitely a need.. but then again everything I want seems to become a need but then I have to convince the wife that it’s a need and that’s the tricky part.😜
great work, it is impressive. How did the hollow pins go when you were using full pressure. the wall thickness seems a bit light and I would be concerned abut them shearing.
Hello, dear friend. You have made a very beautiful, powerful and fast device. May I ask what type of oil pump and with what liter (gallon) you used? Thank you.
What are the wires connected to get the cylinder to extend and retract? I see the pedals, but not what they are connected to that enables reverse flow. Great video by the way!
Thanks J Topel..There are two solenoids that are activated. One for up and one for down. If the up pedal is hit it activates the solenoid and opens the valve for the up hose and the opposite for down. Hope that makes sense.
Hi Paul, I scored the hydraulic power pack unit off of Craigslist for $500. I can’t find the same unit I have but here is one with the same specs and basically the same thing I am using. I can tell you, they aren’t cheap but I have occasionally seen them used for sell online at good prices. www.grainger.com/product/36ND80?gucid=N:N:FPL:Free:GGL:CSM-1946:tew63h3:20501231
Mark R is correct.. I used the largest beams I could get my hands on that wouldn’t cost me an arm and a leg. I checked with every metal building fabricators in my area to see if they had cutoffs from previous jobs. I lucked out and got these for $200. 😃.
The rig looks awesome man. I too am thinking of building my own press. A little problem Though. I life in a country that has little or no component for building a press. My only solution is to orde via Amazon or other company that do online order. The electric pump your using looks better then when you do the manual up and down via a Control Valve. I was wondering what kind of pump assemble you are using. I hear you talk about a solenoid switch's inside the tank. i would be happy if you can provide more info about the power pack unit. I mean where did you buy yours and which website can i look for more info about this type of power pack. Hopefully i can then make a decision when i want to buy one. Also, where did you get that beast of a Hydraulic Cylinder. Thank u in advance and hope to see you begin with your knife journey...👌👌👍🤙
Thanks for watching my video .. To answer your question, I bout my power unit second hand and it already came set up with the solenoids on it. The solenoids just open and close the valves for the hydraulic flow so it can be controlled with electronic switch. This is how I use the foot pedal. My unit came with 6hp motor and 11 gpm pump which sits inside the Hydraulic fluid reservoir attached to the underside of the motor. The u it’s can be pretty pricy new and may not be the most economical way to run a press but I just happened to luck out. I think it would be fairly easy to build your own unit, the pump it uses is very a very standard pump you would fine on wood splitters. As far as the hydraulic cylinder goes, I found it online at www.surpluscenter.com/hydraulics/ 🙏🤙🤙
@@ShalohaCreations Thank u for answering my questions. Like your attitude and the way you make it look so easy. I think i wil build my own like you said. Thanks again and keep up the nice Attitude. PEACE👍✌
I got the I beam from a local builder that builds steel buildings, they were cut offs. The hydraulic ram I bought online from hydraulic surplus, and the power unit I found on buy sell trade used.👍
Hi Katy, there are no plans at this time for this build.. I may in the future start providing plans for my builds, but haven’t gotten that techy yet;) I basically read a bunch of forums and looked at a lot of pictures on line, to build the one I have. If you ever decide to build and have any questions I can answer for you along the way, I would be more than happy to help. Thanks
@@carlocomodi7779 Prego, pero io non sono l’ huomo che ha fatto il video. Io sono mezzo italiano e parlo e capisco un po di italiano…. Pero non tanto come spagnolo e serbo-croato (la famiglia di mia mamma e italiana di Mezzana, vicino a Trento, la famiglia di mi papa e di Serbia, di Belgrado). Io sono nato en gli stati uniti 😊.
@@carlocomodi7779 Cuesto e un link a altro video per una pressa scimilare, en la descrizzione di cuesto video che links per un “plan” con la informazzione per la construzionne de la pressa. Sorry, my Italian is limited. There are other videos online with more detailed information about how to make one of these, like the video linked here. ruclips.net/video/q58iInuNtRY/видео.html
RUclips either has too much great content or the promoting algorithm is broken. Your videos tend to have less than 1k views. And this isn't the only clearly very proficient maker channel with such a low amount of publicity I've seen lately. I remember a time when having an audio where you could actually here talking properly was "production quality" in the maker community here. Here's hoping the youtube algorithm wakes up some day soon.
I sure haven’t figured out the algorithm yet but sure hope at some point it will start to work in my favor. Thanks for noticing all the work I put into this stuff, much appreciated 🙏🤙
@@ShalohaCreations In case you're interested, Veritasium (science channel) made two videos on the subject; “My video went viral. Here’s why” and “Clickbait is unreasonably effective”. They're not gospel, but have a fair few good points with some data to back it up. I mean I personally kinda despise the generic youtube clickbatey stuff (shocked face, pointing or looking at something, an arrow pointing at it, a title like "You'll never believe how good this toast tastes when it's prepared with the SECRET ingredient!"), but I can't deny that it works. At least for now. You don't have to sell your soul to the devil and there is such a thing as over-doing it, but the amount of youtube-uninterest your videos get, it just makes me sad. There's no reason (good content quality, non-marginally interesting subject matter, decent sound quality and editing) that this channel shouldn't be able to do a lot better.
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
I appreciate your genuineness...Shaloha my friend
Shalom my friend, thanks for watching! 🙏🤙
This is definitely a Need vs Want issue for me
Do I need one like that… no
Do I want one like that… Hell ya !!!
Oh it’s definitely a need.. but then again everything I want seems to become a need but then I have to convince the wife that it’s a need and that’s the tricky part.😜
Awesome job. Well done 👍 cheers J
Thank you joshuadelisle 🤙
Blown away by yours skills and knowledge. Brilliant 👍🏼
Thanks again Davesaxon 🙏🤙
I have the slugger saw you have , love that saw. One of the best thing I have bought.
Absolutely.. I agree 🤙🤙
Looks like a great tool to have at your disposal! Looking forward to knife number 2!
Thanks Zengineer.. you and me both😜
Little sketchy but nicely rigged. Big credit for a fantastic build.... Very nice video
Thanks Danwerkman.. yes the build was a little sketchy, but I like to live on the dangerous side 😜 🙏🤙
great job mate,........I want one, 👍
Thanks Geoffrey, I think you should build one for sure ;)
Great job
Thank you 🙏🤙
Hey great build. I've built over a dozen hyd forging presses and yours has some improvements but overall awesome job man.
Thanks joeldavis9473 🤙
great work, it is impressive.
How did the hollow pins go when you were using full pressure. the wall thickness seems a bit light and I would be concerned abut them shearing.
Thanks for watching.. honestly I had the same concern at the time when I installed them, but haven’t had any issues. 🤙
awesome job!
Thank You Craig 🤙
Good job 👏🏽
Thanks James Ball 🙏🤙
Hello, dear friend. You have made a very beautiful, powerful and fast device. May I ask what type of oil pump and with what liter (gallon) you used? Thank you.
It’s 11 gpm pump with 6hp electric motor, and 15 gallon hydraulic fluid 👍🤙
thanks👍
What are the wires connected to get the cylinder to extend and retract? I see the pedals, but not what they are connected to that enables reverse flow. Great video by the way!
Thanks J Topel..There are two solenoids that are activated. One for up and one for down. If the up pedal is hit it activates the solenoid and opens the valve for the up hose and the opposite for down. Hope that makes sense.
Can you share what power unit you used & where I came from? Thanks. Awesome video!
Hi Paul, I scored the hydraulic power pack unit off of Craigslist for $500. I can’t find the same unit I have but here is one with the same specs and basically the same thing I am using. I can tell you, they aren’t cheap but I have occasionally seen them used for sell online at good prices.
www.grainger.com/product/36ND80?gucid=N:N:FPL:Free:GGL:CSM-1946:tew63h3:20501231
How did you calculate what size of beams to use?
The biggest he had
Mark R is correct.. I used the largest beams I could get my hands on that wouldn’t cost me an arm and a leg. I checked with every metal building fabricators in my area to see if they had cutoffs from previous jobs. I lucked out and got these for $200. 😃.
Quanto è la velocità di movimento della pressa? Utilizzi due pompe? Potrei sapere quale tipo di pompa hai utilizzato? Grazie
I bought a used pump from marketplace. Can’t remember the brand, but it pumps upward of 11gpm
What kind of pedal did u use
I used this one.. a.co/d/92mQMFX
The rig looks awesome man. I too am thinking of building my own press. A little problem Though. I life in a country that has little or no component for building a press. My only solution is to orde via Amazon or other company that do online order. The electric pump your using looks better then when you do the manual up and down via a Control Valve. I was wondering what kind of pump assemble you are using. I hear you talk about a solenoid switch's inside the tank. i would be happy if you can provide more info about the power pack unit. I mean where did you buy yours and which website can i look for more info about this type of power pack. Hopefully i can then make a decision when i want to buy one. Also, where did you get that beast of a Hydraulic Cylinder. Thank u in advance and hope to see you begin with your knife journey...👌👌👍🤙
Thanks for watching my video .. To answer your question, I bout my power unit second hand and it already came set up with the solenoids on it. The solenoids just open and close the valves for the hydraulic flow so it can be controlled with electronic switch. This is how I use the foot pedal. My unit came with 6hp motor and 11 gpm pump which sits inside the Hydraulic fluid reservoir attached to the underside of the motor. The u it’s can be pretty pricy new and may not be the most economical way to run a press but I just happened to luck out. I think it would be fairly easy to build your own unit, the pump it uses is very a very standard pump you would fine on wood splitters. As far as the hydraulic cylinder goes, I found it online at www.surpluscenter.com/hydraulics/
🙏🤙🤙
@@ShalohaCreations Thank u for answering my questions. Like your attitude and the way you make it look so easy. I think i wil build my own like you said. Thanks again and keep up the nice Attitude. PEACE👍✌
where did you get your parts from?
I got the I beam from a local builder that builds steel buildings, they were cut offs. The hydraulic ram I bought online from hydraulic surplus, and the power unit I found on buy sell trade used.👍
Fancy Tortilla press 🤭💓❤💓
Hahaha… yes, I like my tortillas supper thin 😜😁🤙
is there a plan available? maybe a link?
Hi Katy, there are no plans at this time for this build.. I may in the future start providing plans for my builds, but haven’t gotten that techy yet;) I basically read a bunch of forums and looked at a lot of pictures on line, to build the one I have. If you ever decide to build and have any questions I can answer for you along the way, I would be more than happy to help. Thanks
About to do some "sketchy stuff" 😅
Yep 😜
Posso sapere quanto è la corsa del pistone? Grazie
Lui ha detto treidiecci inches (13), e trentatrei centimetri (33cm)
Grazie, e complimenti per i video!
@@carlocomodi7779
Prego, pero io non sono l’ huomo che ha fatto il video. Io sono mezzo italiano e parlo e capisco un po di italiano…. Pero non tanto come spagnolo e serbo-croato (la famiglia di mia mamma e italiana di Mezzana, vicino a Trento, la famiglia di mi papa e di Serbia, di Belgrado). Io sono nato en gli stati uniti 😊.
@@carlocomodi7779
Cuesto e un link a altro video per una pressa scimilare, en la descrizzione di cuesto video che links per un “plan” con la informazzione per la construzionne de la pressa.
Sorry, my Italian is limited. There are other videos online with more detailed information about how to make one of these, like the video linked here.
ruclips.net/video/q58iInuNtRY/видео.html
@@firmamentbubbleboyaskstobe7076 Grazie di nuovo
6" cylinder with a 3-1/2" bore? Does not compute.
RUclips either has too much great content or the promoting algorithm is broken. Your videos tend to have less than 1k views. And this isn't the only clearly very proficient maker channel with such a low amount of publicity I've seen lately.
I remember a time when having an audio where you could actually here talking properly was "production quality" in the maker community here.
Here's hoping the youtube algorithm wakes up some day soon.
I sure haven’t figured out the algorithm yet but sure hope at some point it will start to work in my favor. Thanks for noticing all the work I put into this stuff, much appreciated 🙏🤙
@@ShalohaCreations In case you're interested, Veritasium (science channel) made two videos on the subject; “My video went viral. Here’s why” and “Clickbait is unreasonably effective”. They're not gospel, but have a fair few good points with some data to back it up.
I mean I personally kinda despise the generic youtube clickbatey stuff (shocked face, pointing or looking at something, an arrow pointing at it, a title like "You'll never believe how good this toast tastes when it's prepared with the SECRET ingredient!"), but I can't deny that it works. At least for now.
You don't have to sell your soul to the devil and there is such a thing as over-doing it, but the amount of youtube-uninterest your videos get, it just makes me sad. There's no reason (good content quality, non-marginally interesting subject matter, decent sound quality and editing) that this channel shouldn't be able to do a lot better.
promosm 🤗
🙏🙏🤙
Bla-bla
Bla
I want a wonky knive! Looks like fun. Enjoy….
Hahaha.. I’m good at wonky.. I could make that happen. ;)