Installing OctroPrint On Your 3D Printer Has Never Been Easier! (Pi Zero 2 W OctoPi Guide)

Поделиться
HTML-код
  • Опубликовано: 28 авг 2024

Комментарии • 210

  • @SentryGaming275
    @SentryGaming275 24 дня назад +1

    I have no words... I just turned my simple Ender 3 Pro into a Bambu Lab A1, I don't even have to use the printer's old school interface anymore, I can just control it from my phone! Thank you so much, this is one of the most helpful 3D printing tutorials I watched yet.

  • @cynic5581
    @cynic5581 2 года назад +4

    Thank you! I bought a Raspberry Pi 4 back when I thought I was able to be clever. Needless to say it sat around unused. Following your steps I got it set up with my Ender3v2 for a much more convenient printing setup! Thanks again!

  • @rwz
    @rwz 2 года назад +17

    To prevent the pi powering the printer you can put some tape over the usb power pin on the usb-a side.

    • @JarredSutherland
      @JarredSutherland 2 года назад +2

      I wanted to not only thumbs up this but comment, very important step!

    • @3dFirefly
      @3dFirefly 2 года назад +1

      oh wow! I wish I thought of that before cutting the power wire on my cord. Kapton tape probably would be good to use.

    • @spaghettigod1794
      @spaghettigod1794 Год назад

      what the heck

  • @alanb76
    @alanb76 10 месяцев назад

    It's the Pi Zero 2 W. Now that we can actually get them, this is useful!

  • @prongATO
    @prongATO 2 года назад

    Going to have to say, you have the coolest logo of any 3D printing channel!

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Thank you very much 😊

  • @pieyed1302
    @pieyed1302 2 года назад +4

    Great video! Thanks. I would like to see the next step... installing Mainsail/Klipper on an OctoPi setup.

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Thank you Pi! I am not sure if I can run Mainsail unless it is a dual boot scenario but the Klipper side will definitely be happening :).

    • @pieyed1302
      @pieyed1302 2 года назад

      @@ModBotArmy Cool! Thanks

  • @thornbottle
    @thornbottle 10 месяцев назад

    Thanks for this video, just got an ender 3 vs neo today and didnt know really what to do with my pi 2 zero, so now ive turned my printer wireless :)

  • @therealmakmillion
    @therealmakmillion 2 года назад +3

    I got two of these in a few days back and need to get them set up, but they sure do look beastly with that “new” SOC! Can’t wait to really push them to see how much they’ll take.

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Yeah I am loving this board. It is such a good blend of price to performance.

  • @domenicprinzivalli8318
    @domenicprinzivalli8318 2 года назад +2

    Definitely interested in seeing an octoklipper vid. Thanks for the awesome videos!

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      I will make it happen. Thanks for watching :)

  • @ObsequiousV4
    @ObsequiousV4 5 месяцев назад

    I was initially under the impression that octoprint replaced the Ender 3's firmware and board. Thanks for this video. I would have added a pi to my setup long ago had I realized it was a separate entity

  • @ethzero
    @ethzero 2 года назад +5

    I know OctoPrint/PI isn't recommended on a Raspberry PI Zero 1, but a 2 makes sense give the spec bump.

  • @Twin_Flyer
    @Twin_Flyer 2 года назад +3

    Perfect timing! Been trying to use that imager and wondering why I could not see my Pi on the network. I somehow missed the part where you choose the right OS! Worked perfect after this vid, Thanks!!

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Sweet! Happy to hear :) Enjoy!

  • @ChadLower
    @ChadLower 2 года назад

    Love it. This dude is genius. Finally got my raspberry on the Wi-Fi.

  • @occamraiser
    @occamraiser 6 месяцев назад

    The OCTOPI build on the Pi Zero 2 W took me about five minutes. It was remarkable and needed no setting up.
    BUT if you want VNC and all the other Raspberry pi GUI based interface in addition to Octoprint - go the 'install octoprint onto an existing Raspberry pi' route, not the all-in-one octopi build method. My RPI won't support the standard 'startx' GUI because octopi is a subset of the standard Raspbian.

  • @johnbickford9221
    @johnbickford9221 2 года назад

    I love Micro Swiss and as a bonus they are based in Minnesota about 25 miles from me.

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Hey! How cool. Always awesome to support a US company making products in the US.

  • @kristofferbenjamin6854
    @kristofferbenjamin6854 2 года назад

    @ModBot FING app reccomended:
    Hey! You said the easiest way to see the pi ip adress was logging into the router. I used to do the same, until i started having to set up pis at my workplace where i dont have access to the router, and had to rely on the hostname.
    UNTIL: i discovered an app called "FING" that scans the network and shows devices as well as online time, hostname and so on. It even has an option to wake on lan, ping and ssh via an ssh app. The app is definitely reccomended! it's available on both IOS and Android, and is a lot easier thatn logging into router, no matter how easi that may be ;)

  • @bwselectronic
    @bwselectronic 2 года назад

    Thanks. I just managed to get a Canakit Pi 0 2w kit. Your tutorial should come in handy.

  • @Noah-Davis
    @Noah-Davis 2 года назад

    I was looking up how to do this less than an hour before you posted this video, lol.

  • @RussDahlberg
    @RussDahlberg 2 года назад

    Pi Imager is dope. So much faster than hunting for IMGs and using etcher.

  • @baivesan
    @baivesan 2 года назад +19

    I'd love to see how well Klipper will run on that. I do have several projects, that would innclude installing klipper on a printer and i'd rather not have to buy a full size PI, they are rather expensive.

    • @4thfrom7
      @4thfrom7 2 года назад

      I'm in exactly the same position.

    • @varunpatel1988
      @varunpatel1988 2 года назад +3

      It runs really well. I installed it on my ender 3.

    • @corey640
      @corey640 2 года назад +2

      $45 is "rather expensive"?

    • @adameichler
      @adameichler 2 года назад +1

      Kossel Linear Plus, Klipper, Fluidd, Pi Zero 2, no webcam, runs lovely.

    • @baivesan
      @baivesan 2 года назад +7

      @@corey640 More like 80$ where i live, 10% of my monthly salary.

  • @glennedward2201
    @glennedward2201 Год назад

    Hmm, I’ve got an H6 orange pi. Read somewhere it will work. Orange pi had more features and expansion and also allowed me to use a full size solid state drive to install the operating system to.

  • @zk_6312
    @zk_6312 7 месяцев назад

    Of course you can use the octoprint with klipper though you do have to make some changes to octoprint to get it to work with klipper.

  • @theoldpcguy
    @theoldpcguy 2 года назад

    Great video, good luck finding one though! Only one reseller had any in stock, 32, limit one per customer. Actually all models were sold out pretty much everywhere.

  • @jon9947
    @jon9947 2 года назад

    Awesome video. Wish I had bought more of the Rock64 boards when they were so cheap on Amazon, so was pretty excited about this new Pi.

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      I dont know if I am familiar with the Rock64, maybe I am haha. Is it a small 64 bit sort of all in one computer like the Pi?

    • @the_arcanum
      @the_arcanum 2 года назад

      @@ModBotArmy yup, it's a nice contender for low power sbc home servers when you can't afford AsRock or SuperMicro SOC itx boards. It's a bit more evolved than the RaspBerry Pi.

    • @jon9947
      @jon9947 2 года назад

      @@ModBotArmy Its the same size as the Pi, and power wise its right about in the middle of the Pi3 and Pi4. I missed the super cheap train, if you read the reviews on it there was some people who picked them up for $5ish, I bought mine when they were $15. It came with 100% of everything you would need to use it, a power brick, a case, a micro sd card. It even came with a small little screen, the screen was sorta useless for Octoprint, but extra is extra.
      Probably would have made a nice SBC for a small/cheap NAS too, as it has USB 3 and gigabit ethernet. Amazon has since sold out of them, and every time they restocked them, the price went up.

  • @RamonInNZ
    @RamonInNZ 2 года назад

    You can disable the 5V wire in the connector between the Pi Zero and the printer - comms only need the data and grounds wires to be connected.

  • @ized88
    @ized88 2 года назад +1

    I'm trying octoprint on my old fire 7 tablet next. Would probably be the cheapest solution for me, as you already have a cam and Touchscreen, too.

    • @wayneuk
      @wayneuk 2 года назад

      i was using a old phone but battery kept killing over n crashing the printer

    • @ized88
      @ized88 2 года назад

      @@wayneuk get a y cable for around 3€?

  • @mlubecke
    @mlubecke 2 года назад +1

    This is great 👍🏻 stuff. Thank you so much 😊

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Absolutely! Thanks for watching :)

  • @jamesnewnam9889
    @jamesnewnam9889 2 года назад

    I would love to see the OctoKlipper video. I just got my Pi 0 Wireless v2 today, so that would be a cool project for it.

    • @ModBotArmy
      @ModBotArmy  2 года назад +2

      It sounds like there is a lot of interest in this so I will see if I can make it happen in the next few weeks :)

  • @michaellindborg1510
    @michaellindborg1510 2 года назад

    Yes, OctoKlipper would be awesome!

  • @joell439
    @joell439 2 года назад

    👍😎👍. Definitely like to see octroklipper install

  • @FutaNoKami
    @FutaNoKami 2 года назад

    I'm going to try this in combination with a "USB ETHERNET HUB HAT VOOR RASPBERRY PI ZERO" So i can have the stability of wired internet and some more usb slots for e.g. cameras or connecting to the printer instead of the flimsy micro usb port. I will also use the printer power supply with a dc-dc converter so i dont need external usb power.

  • @entropic7768
    @entropic7768 2 года назад

    Thank you, very easy to follow

  • @The1Perfume
    @The1Perfume Год назад

    YESSSS PLEASE!!!! Octoklipper!!!

  • @davidolsson
    @davidolsson 2 года назад

    I vote for bying an old android and run octo on that. Same price, higher specs and camera included!

  • @JimBell20
    @JimBell20 2 года назад

    Please consider modifying the case lid and add some holes/slots for heat dissapation. I, for one. don't want the fully enclose the pi without providing some way for the heat to get out.

  • @techdegenerate286
    @techdegenerate286 2 года назад

    TOTAL Interested!!!!

  • @RixtronixLAB
    @RixtronixLAB 2 года назад

    Nice video clip, keep it up, thank you for sharing it :)

  • @matthewsuggs1637
    @matthewsuggs1637 2 года назад +1

    good luck getting the pie 02w, i've been waiting to buy several but none of them have came in stock.

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Sorry to hear. They have been easier to find in the US than I would have imagines.

  • @CharlesLeo
    @CharlesLeo 2 года назад +2

    Hey thanks for the simple walkthrough as I’m new to Pi altogether and am receiving my board soon. Here’s a question: are you able to install other software onto the Pi 2 W alongside Octoprint as well? I’m thinking it might be nice to run something like Vaultwarden, or would you just suggest a different route?

  • @37Kilo2
    @37Kilo2 2 года назад

    I was going to use a pi zero 2 on my new Prusa, but they're sold out everywhere. Guess I'll be using my pi 4 since it's on hand.

  • @douglasdweck6804
    @douglasdweck6804 2 года назад +1

    Where can I get a Raspberry Pi Zero 2 W? It seems impossible to find.

  • @MorrWorm8
    @MorrWorm8 Год назад

    So surely you can run this with the pi 3 A+? It’s the exact same thing. I like it because well because I actually have one and can’t get a pi zero 2

  • @-HOSS-
    @-HOSS- 2 года назад +1

    Hello, thank you for your video. Do you lose any functions by using the pi zero compared to using the pi 3 or 4?

  • @saltyscorpion2151
    @saltyscorpion2151 2 года назад +4

    Great video. Where are you finding the Pi 2s for $15? Amazon prices in the US are 3 times that cost.

    • @andreamitchell4758
      @andreamitchell4758 2 года назад +2

      I got one yesterday at microcenter, they sell out quick though
      in store only too I think

    • @saltyscorpion2151
      @saltyscorpion2151 2 года назад +2

      @@andreamitchell4758 Thanks

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      I got them from Digikey :)

    • @Pickle312
      @Pickle312 2 года назад

      Any idea on how long their back order wait is?

    • @throwitatthewall6289
      @throwitatthewall6289 2 года назад

      Go to the official Pi website and click what you want to buy and they will show you a list of stores you can get it from. I had to go through about 4 before I found one with them in stock. I ordered it about two days ago.

  • @martshal
    @martshal 2 года назад

    Hoping you do follow this up with a octoprint/klipper/pi zero 2.

  • @joshuawilliams3525
    @joshuawilliams3525 10 месяцев назад

    I followed the steps but for some reason the pi won't connect to the wifi network. I tried connect via ethernet cable and that works but when I disconnect the cable, I get disconnected. Can you off any advice?

  • @minerwilly
    @minerwilly 2 года назад

    Great video and very helpful, thanks.
    But £ is a pound sign ;)

  • @BuildThoseSkills
    @BuildThoseSkills Год назад

    $15 board? I wish!! Where can I get one of these for $15? I found some on Amazon for $120! Over the last few years there seems to be a great shortage of Raspberry Pi, unless you just want an older model or a pico, they cost an arm and a leg. What's going on with RPi these days?

  • @fagustini
    @fagustini 2 года назад +1

    Your video was very helpful and I installed octoprint on a pi0 w 2.. only issue is if the pi is still powered up I can't turn off my printer... it's a faint screen but it's still on until I un-power the pi. I purchased the cable you recommended from amazon but it must have data and power capability... any ideas???

    • @ModBotArmy
      @ModBotArmy  2 года назад

      I have seen others either physically block the 5v pin with something like a piece of tape or a bit more aggressive cut the cable and cut the 5v line.

  • @wayneuk
    @wayneuk 2 года назад +2

    i found the pi4 way quicker in loading files over the zero2 w

  • @609lawson
    @609lawson 2 года назад

    Hi, just got my ender 5 pro and want to run it wireless like you have done here, I just wanted to check with you since this video was made months back and ask you if there was newer items and software I should get Thanks

  • @slabua
    @slabua 2 года назад

    Micro-to-micro usb otg cables for convenience also exist.

  • @MorrWorm8
    @MorrWorm8 Год назад

    Noob here. The OctoKlipperPi is available. That a good choice to go with?

  • @Deathbysnusnu125
    @Deathbysnusnu125 2 года назад

    got octopi set up on mine. then went to try out the next morning. Board seems to have died somehow :( Won't power up or anything.

  • @iPrintDreams3D
    @iPrintDreams3D 2 года назад

    Thank you for the video. Took me a while to understand that I had to wait for octopi to auto login and then grab IP from network on computer or through internet provider.

  • @cyganskieoko
    @cyganskieoko Год назад

    Whi po zero w is not enought? Can You explain why You need pi zero w 2? For this

  • @webflys
    @webflys Год назад

    Pi Zero W working great too 👍

  • @levireidhead
    @levireidhead 2 года назад

    On the Pi Zero 2W, how do I physically connect my Logitech c270? and which is the best plugin for viewing and time lapse?

  • @The_Traveling_Clown
    @The_Traveling_Clown 2 года назад +3

    I've been thinking about upgrading my Ender 3 V2 to a linear rail system. Is it worth it and where can I find one not shipped from china??

    • @WatsitTooyah
      @WatsitTooyah 2 года назад +3

      I've seen on another video that it doesn't really make a difference in print quality.

    • @bentracy7463
      @bentracy7463 2 года назад +2

      I've been running a couple modified E3Ps for a while now and I don't see a need for a linear rail setup. Once you have them tuned in, print accuracy is completely fine for most projects (I use mine primarily for functional parts).

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      I would argue not a huge noticeable difference. It is going to be stiffer and I would be curious to see if it has much affect on tolerances but I think it is a pretty overkill mod. That being said it has never stopped me before so if you want to I say hell yeah. The low cost ones can be decent if you do not mind shipping and cleaning them when you get them.

    • @The_Traveling_Clown
      @The_Traveling_Clown 2 года назад

      @@ModBotArmy Is the length for the Ender 3 v2 linear rails 300mm or 400mm??

  • @V8ToYy
    @V8ToYy 2 года назад

    please someone show this setup with a wired connection to the internet. it should be easy but cannot figure it out, only ever get shown wireless setup. i tried just plugging the ethernet into the pi and no luck, its working over wirelss but the camera is lagging behind about 5 mins so wont a better more stable connection but seems like you cant, even tho theres a ethernet port on the board

  • @nahpeasohian
    @nahpeasohian Месяц назад

    Can I use a Micro USB to Micro USB cable instead of what you recommended? Thanks!

    • @Icee_Spise
      @Icee_Spise 23 дня назад

      i'm sure that will work👍

  • @zigeprivate7468
    @zigeprivate7468 2 года назад

    I bought the RPI zero 2 w, installed the OctoPrint, everything works just fine exept for the webcam, I could not get it working, it just wont connect

  • @Dumdadum76
    @Dumdadum76 2 года назад

    9:52 I can’t seem to find the shaper 3d software you’re using. Could you please provide a link? Many thanks!

  • @primoziskra6394
    @primoziskra6394 2 года назад

    Hello. Is it posible to configure marlint through raspberry? will be any tutorial for this. Thanx

  • @grakka72
    @grakka72 2 года назад

    Hmm The PI has a camera onboard, just have to connect to the pi !? Don't need the use of USB!?

  • @uksuperrascal
    @uksuperrascal 2 года назад

    Imager will not install on ubuntu studio 18.4 - Pi Legacy OS is better it is all plug and play no setting to worry about.

  • @kslim34
    @kslim34 2 года назад

    What's the software of choice that is used for editing and creating your designs?

  • @rockcityfpv9117
    @rockcityfpv9117 2 года назад

    I use a Banana pi M2 Zero... its nice but may convert to this one based on this video

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Is that a clone of the pi Zero? I know there are some other similar boards based on the Pi. Not sure I have heard of the Banana though.

    • @rockcityfpv9117
      @rockcityfpv9117 2 года назад

      @@ModBotArmy YEP same form-factor and pin out ... everything that PI Zero is now. FYI I ordered the new Pi Zero W2 since it has better support and compatibility.
      The Banana Pi was no slouch just sucky camera support

  • @ZeonsZone
    @ZeonsZone 2 года назад

    Sweet video! Curious, if you have a pi 3 b+ do you think it is worth spending the time and money to upgrade to a pi 4 8gb to run octoprint or other software for a voron, or do you think the 3 b+ would be suitable and able to handle the software and run a cam or 2?

  • @mikeneron
    @mikeneron 2 года назад

    I hooked this up tonight and could only get it working if I plugged the USB OTG cable into the 2nd port. If I used the first port it just wouldn't work, so I gather that is by design. I had some right angle USB OTG cables I was hoping to use, but those are out as they would block the power one. Will have to order a left angle one to make it a bit neater, but luckily had a straight one that will work for the time being. It's nice to have a Pi devoted to each printer.

  • @FLQ309L
    @FLQ309L 2 года назад

    I have a epax 156 do you think this will work for my printer?

  • @priyan776
    @priyan776 2 года назад

    Great video. If you know, will you be able to do a video "how to add multiple webcams to octoprint"? The old method doesn't work anymore or I'm doing something wrong.

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Not something I have done. Would the reason for this be to make cool timelapses from different angles? Or just if a print gets tall to make sure nothing if failing?

    • @priyan776
      @priyan776 2 года назад

      @@ModBotArmy I like to put one camera to the Filament roll since I have couple web cams laying around. There is a multi cam plugging in plugging manager, but I did not had any luck.

    • @priyan776
      @priyan776 2 года назад

      @@ModBotArmy ruclips.net/video/FzpBgEG_ksw/видео.html
      This is so outdated.

  • @TOjoe1strow
    @TOjoe1strow Год назад

    So did he need any visual interface to identify if what he did worked?

    • @TOjoe1strow
      @TOjoe1strow Год назад

      I was under the impression I needed to see how the pi handled the os

  • @TwanJaarsveld1
    @TwanJaarsveld1 2 года назад

    What if the light just doesn't show anything

  • @3rutu5
    @3rutu5 2 года назад

    Damn, got excited, then realised i only have the Pi Zero W.......

  • @holgerst3607
    @holgerst3607 Год назад

    can i use the raspberry pi zero 1?

  • @Zanezzzzzzzzz
    @Zanezzzzzzzzz 2 года назад

    I wish i did this instead of preordering a pi 4 thats never coming

  • @madebyandre_
    @madebyandre_ 2 года назад

    OctoKlipper please!

  • @etienne_fpv8946
    @etienne_fpv8946 2 года назад +1

    Modbot? do you have a discord?

    • @ModBotArmy
      @ModBotArmy  2 года назад

      In video description 😬

  • @darkonikolic8377
    @darkonikolic8377 2 года назад

    Thanks a lot, does it live stream well with Pi camera?

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Everything I have seen points to yes absolutely.

  • @michaelbailey1420
    @michaelbailey1420 11 месяцев назад

    I had an orange pi 3 that im using for octo print now. the useless H6 orange pi 3.

  • @lucasi8455
    @lucasi8455 2 года назад

    How to set a good 2 axys or 3 axys CNC using rasp?

  • @andreamitchell4758
    @andreamitchell4758 2 года назад

    Just bought a pi zero 2 w yesterday and was thinking of using it for this
    but I am wondering if for my needs a 1st gen pi zero W will do
    ender 3 pro and jus for simple printing , can you explain the differences ? how much slower is it?
    I have a wyze v2 I was going to use for a camera with it's original FW or RTSP FW
    so I won't be using a camera with it , I guess I could use the pi zero 2 W with the wyze cam connected to it via USB if I flash the wyze web cam FW to the camera and view it through octoprint instead of wyze app

    • @housinit
      @housinit 2 года назад +1

      Where did you manage to find a place to order them from? They're sold out everywhere I'm looking.

    • @andreamitchell4758
      @andreamitchell4758 2 года назад

      @@housinit Microcenter , in store
      1st time they came in stock they sold out in a day , about a week later they were back
      they had 25+ not sure if there still in stock now thought that was few days ago

    • @ModBotArmy
      @ModBotArmy  2 года назад +2

      Totally up to you. I used the gen 1 with no cam and didnt mind it. Hell I ran them in a farm config and had no issues. I have not done a side by side speed wise but if you already have the original zero w maybe try that and see how you feel.

  • @Ron_Ventura
    @Ron_Ventura 2 года назад

    I have Octopi set up on a Pi 4. Can I just plug in the microSD card without going through the install process?

    • @ModBotArmy
      @ModBotArmy  2 года назад

      That is a great question. I cannot see why not, however I am not entirely sure if there is anything done on first boot that would sign the micro sd card to a specific pi. I dont think that would be the case. If you do please let me know the outcome.

    • @Ron_Ventura
      @Ron_Ventura 2 года назад

      And I’d really LOVE to know where I can get one of these for $15. Looking on Amazon (Australia) they are nearer AU$100. I know our dollar is weak, but it’s not that weak.

  • @twinturbostang
    @twinturbostang 2 года назад

    Does this work in parallel with Marlin then? For some reason I thought it replaced it and was the printer's new "firmware".

    • @paulradford4100
      @paulradford4100 2 года назад +1

      Marlin stays as the firmware for your printer.
      Octoprint is loaded on to the raspberry pi, which is connected to the USB on the printer like an external device.
      The pi simply sends the gcode to the printer via the USB.
      Basically, Octoprint gives you WiFi control (by Web interface), which is actually very useful. It can also use a camera to allow you to watch the print without being right next to it and a bunch of other useful stuff

    • @twinturbostang
      @twinturbostang 2 года назад +1

      @@paulradford4100 Thanks!

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Yup! So it is just an interface between the Octoprint and Marlin on your printer :). For Klipper it is a different scenario as it is its own firmware that runs on the Pi.

  • @mateng7707
    @mateng7707 2 года назад

    I have a voron. A pi zero would not be powerful enough to run klipper. So it’s not the perfect choice

    • @ModBotArmy
      @ModBotArmy  2 года назад

      This is a pi zero 2 which is powerful enough to run klipper 👍

  • @the0bone
    @the0bone 2 года назад

    Wasn't there a need to SSH into the PI to enlarge the storage to the full SD card?

    • @ricks1936
      @ricks1936 2 года назад

      No, its automatic now on the current releases of octopi.

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Yeah I believe that was only with the older method of manually installing. With the current setup there is no need.

    • @the0bone
      @the0bone 2 года назад

      @@ModBotArmy I followed your steps yesterday and the boot partition was very small and 7GB where unformated till I added them.
      SSH into the PI
      sudo raspi-config
      // first to make sure all is fine
      update
      // after that into advanced
      expand_rootfs
      // and
      Finish

  • @6yjjk
    @6yjjk 2 года назад

    Go ahead and take a shot every time he says "go ahead and" :P
    Useful content though.

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      Don’t! Haha unless you have nothing to do.

  • @aliciahoflack138
    @aliciahoflack138 2 года назад

    you know a good blocker that blocks the power on usb for my ender 6? i have no idea what to look for? i do live in eu.

    • @paulradford4100
      @paulradford4100 2 года назад +1

      I used an old USB cable and peeled off the outer sleeve. I cut a section of the red v++ wire and used electrical tape to cover the wires.
      I felt this to be necessary, as the printer would try to power from USB (dim glow on printers screen). In my mind this is dangerous and must be looked at, as 5he USB bus is not meant to supply 24v and worst case scenario is fire.
      I have heard of folks attaching USB to the computer before powering on the printer - the result being a corrupt firmware on the printer and a fried USB bus on the computer.
      Be aware if your printer lights up by USB...

    • @ModBotArmy
      @ModBotArmy  2 года назад

      You mean to prevent the Pi from trying to power the printer or to prevent the printer from trying to power the Pi? I have never ran this but if you did want to I have seen some use a thing tape strip to cover the 5V line. Or as mentioned below you can also remove the outer cover and cut the connection of the 5v line.

    • @aliciahoflack138
      @aliciahoflack138 2 года назад

      @@ModBotArmy the ender 6 seems to like put power on the 5V and that makes it that the printer sometimes just doesn't power on properly. i really want to use octoprint but i don want to fry it or my printer. i saw another youtuber using a blocker between the printer board and the pi. thought maybe you know were to find this, is it save to just disconnect/cut the 5V?

  • @PandaChan89
    @PandaChan89 2 года назад

    Can I use the gpio pins for the mk3s like I could with prusa print?

    • @ModBotArmy
      @ModBotArmy  2 года назад

      It should not be an issue. This does draw a bit more power but I swore I saw a few posts in Prusa forums saying it was no issue. I would double check just to be safe before.

  • @audiophileuser
    @audiophileuser 2 года назад

    octoklipper please :)

  • @Themakersworkbench
    @Themakersworkbench 2 года назад +3

    Pressing CTRL + X (CMD+X) in Raspberry Pi Imager will open the advanced configuration setup menu. You can set the WIFI and SSH access there before burning the image, and remove the supplicant.wpa and .ssh file edits. I made a video about it a few months back.
    ruclips.net/video/eS-N8NCB9rk/видео.html&t

  • @mitofun6967
    @mitofun6967 2 года назад +1

    Yep but 60 usd for pi z 2 is too much !;(((

  • @DougSisco1
    @DougSisco1 2 года назад

    So why is the title “Octrorprint”?

  • @mushroom5912
    @mushroom5912 2 года назад

    No link for the pi :/

    • @bennylloyd-willner9667
      @bennylloyd-willner9667 2 года назад

      I've read a few comments here that they sell out quickly so the advise someone wrote is to go to the official pi website and get links there. It can't be that hard to Google some shops tho.

  • @jnssmnsn
    @jnssmnsn 2 года назад

    Does this work on a Creality CR10S Pro V2 ?

    • @ModBotArmy
      @ModBotArmy  2 года назад

      Should not be an issue. Just connect over USB.

    • @jnssmnsn
      @jnssmnsn 2 года назад

      @@ModBotArmy Actually after researching online the CR10 / CR10s pro v2 seems to have problem with it. People reporting gantry crashing into various places, so definitely not something you want to recommend to people without them looking into it !

  • @melbatoast1985
    @melbatoast1985 Год назад

    i can't with "lybary"

  • @siedliko
    @siedliko 2 года назад

    £16 zero 2 W + £15 webcam C270 + £4 some cables
    So for £35 you are ready to control and watch the printer.

  • @cnc-maker
    @cnc-maker 2 года назад

    PSST! Pi Zero 2W ;)

    • @ModBotArmy
      @ModBotArmy  2 года назад +1

      lol updated. Thank you :)

    • @andreamitchell4758
      @andreamitchell4758 2 года назад

      I still think pi zero w 2 makes more sense
      R PI foundation dun goofed
      I was searching for w2 and nothing was coming up when trying to buy one
      W 2 makes more sense IMO

    • @jerseybarrier64
      @jerseybarrier64 2 года назад +1

      So I took the plug and ended up getting a pi zero w which may have been a mistake. I got an error message from Octoprint saying this pi is and never will be supported. It did seem to connect but now not sure I should stick with it. Guess I need to now upgrade to a 2W. Anyone using the pi zero w?

    • @andreamitchell4758
      @andreamitchell4758 2 года назад

      @@jerseybarrier64 have you tried using an older version of the octoprint image? maybe Daniel could suggest one?

    • @jerseybarrier64
      @jerseybarrier64 2 года назад

      @@andreamitchell4758 thanks and no have not. The board is working but sounds like I may run in to stability issues. This is all new to me (thanks Daniel ;) )

  • @bryannamba1560
    @bryannamba1560 2 года назад

    Has anybody installed a Pi on a Lerdge board???