Tips. Very important if you would like to saw with precision. (avoid torsion as much as possible)! Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade,it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / HITACHI C12RSH2 / Bosch GCM 8 SDE / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact. (This also is the case with the Miter saw without the slide rails). If you want you can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood about +- 20 mm thick to this with the normal handle positioned on the right side of the Miter saw (the wood it will remain in place until the test is completed). Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut. If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing (test is completed). Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade. Conclusion: how further away the handle is from the saw blade how more chance of torsion in the aluminum housing.(don't go for that).
Last Ryobi tool up close I saw about 10 years ago and it felt crappy and cheap but I see they come a long way, just got myself Ryobi table saw, and Im very happy with it. Mitre saw is next on the list. Thanks for the review.
Chris C that's just with the cloth bag, i have this funnel connected to my dust collector in the back of the miter saw station that's supposed to collect some of the dust in the air, but I think it might be time to empty the bag - looks pretty full, so that might be part of the problem 😂. Haven't tried it with the shopvac connected to the saw yet.
Trond-Daniel Kvalvik hei! Prøver å huske om jeg sjekket evt. Justerte den når jeg monterte den, men klarer ikke huske.. tror min skal være rimelig rett, skal ta å dobbeltsjekke når jeg kommer hjem om den faktisk er det. Min ble bare sånn halveis montert i sagbordet på denne videoen, den er ikke helt den samme dimmensjonen som den gamle saga, så har måtte finjustere høyden og en masse andre ting siden.
Hei! Jeg hadde samme Bosch som du hadde. Jeg kjøpte nylig en Festool Kapex 120. Har aldri vært borti lignende. Bare gode ting å si. Spesielt på støvoppsamling (med støvsuger). Ikke billig, men kampanjedager og demo sag hjelper. Liker løsningen din bak sagen 👍🏻
Stian Hammervold ja, det er ALT for dyre. Men jeg er så lur at jeg har sort benk og blir gal av å se sagmugg overalt. Prisen var 16000, men fikk den for 11000 2 dager gammel. Dave Stanton på RUclips har mye om denne sagen. Anbefales å se :)
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Tips.
Very important if you would like to saw with precision. (avoid torsion as much as possible)!
Always choose a Miter saw with a handle positioned in a vertical line above the saw blade.
Everything must be aligned, slide rails, handle, and saw blade,it is much better this way the blade will not tilt.
Because there is some torsion in the aluminum housing .
And choose an engine with softstart on it to prevent wear of the gear and worm shaft.
It is very important that everything is aligned.
Here are some examples to show how the handle must be positioned above the blade.
Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / HITACHI C12RSH2 / Bosch GCM 8 SDE / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact.
(This also is the case with the Miter saw without the slide rails).
If you want you can test it yourself at home if there is torsion in the aluminum housing.
Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood about +- 20 mm thick to this with the normal handle positioned on the right side of the Miter saw (the wood it will remain in place until the test is completed).
Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine.
Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut. If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing (test is completed).
Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade.
Conclusion: how further away the handle is from the saw blade how more chance of torsion in the aluminum housing.(don't go for that).
I bough this recently. There are no holes in the fence for attaching a wooden fence extension. Did you drill any? If so, any tips?
How accurate is it? Males perfect 90/45 degrres cuts?
So how would you answer your question after three years? Did you downgrade or upgrade?
A little of both 😉 it can cut bigger lumber than my old saw, but the dust collection is absolutely terrible..
Does this saw have positive mitre stops at set angles like 45 and 22.5? Thanks
Yes it does 😊
How do I ajust the laser?
How is the build of the saw, is it sturdy or feels bit cheap ??
+landlash now that i've gotten used to it, it feels good. The build quality is pretty good.
They don't make this anymore... The new one is a lot better
Last Ryobi tool up close I saw about 10 years ago and it felt crappy and cheap but I see they come a long way, just got myself Ryobi table saw, and Im very happy with it. Mitre saw is next on the list. Thanks for the review.
how are you finding the saw?
Chris C I've gotten used to it now and it works alright, but the dust collection sucks.. the dust goes everywhere!!
Stian Hammervold is that with an extractor or just the cloth bag? Thanks for the reply.
Chris C that's just with the cloth bag, i have this funnel connected to my dust collector in the back of the miter saw station that's supposed to collect some of the dust in the air, but I think it might be time to empty the bag - looks pretty full, so that might be part of the problem 😂. Haven't tried it with the shopvac connected to the saw yet.
@@stianhammervold I have mine connected to a shopvac and it's still poor
Har samme sag selv og opplevde da at 0 grader ikke var helt 0. Virker som den må finjusteres men har ikke kommet så langt. Har du opplevd det med din?
Trond-Daniel Kvalvik hei! Prøver å huske om jeg sjekket evt. Justerte den når jeg monterte den, men klarer ikke huske.. tror min skal være rimelig rett, skal ta å dobbeltsjekke når jeg kommer hjem om den faktisk er det. Min ble bare sånn halveis montert i sagbordet på denne videoen, den er ikke helt den samme dimmensjonen som den gamle saga, så har måtte finjustere høyden og en masse andre ting siden.
Hei! Jeg hadde samme Bosch som du hadde. Jeg kjøpte nylig en Festool Kapex 120. Har aldri vært borti lignende. Bare gode ting å si. Spesielt på støvoppsamling (med støvsuger). Ikke billig, men kampanjedager og demo sag hjelper. Liker løsningen din bak sagen 👍🏻
Heldiggris!! Festool er drømmen - en dag ;) synd de koster heroin! men man får også kvalitet.
Stian Hammervold ja, det er ALT for dyre. Men jeg er så lur at jeg har sort benk og blir gal av å se sagmugg overalt. Prisen var 16000, men fikk den for 11000 2 dager gammel. Dave Stanton på RUclips har mye om denne sagen. Anbefales å se :)
السلام على من اتبع الهدى من ابن احصل على واحدة المرجو ا
امساعدة