First did you download the Acorn Installation manual ? It's explained there. Use the Centroid CNC Users forum. Post a fresh report and ask your question there. But it IS explained in the installation manual which can be found on Centroids website
I ran this test and had no problem, but after connecting it to the VFD, the voltage was severely loaded down, reading about a third of what it should be, and was jumping around. Turned out that not shielding the cable carrying the analog command to the VFD is a BAD idea, at least for my setup.
Marty, If this was working and now not getting any output but everything else is working fine. What have I screwed up LOL. I was trying to wire it to a KBSI-240D so clearly I did something wrong.
Thanks Marty. Somehow I missed this in all the prior videos I watched. How do I calibrate these settings so that the spindle is running at close to the RPM my g-code is setting. I have a 24K spindle that I use for carving wood most of the time around 10K to 12K but when cutting fine inly pieces the spindle speed goes way up. Thanks...
Hello Marty, can this test be done after the fact? I bought my board before this test existed and my machine is all assembled and VFD is hooked up..Also do I need to update to the latest version of Acorn for this test to work? Thanks for your help
Do we have to hook up our spindle to a VFD? I've modified all my manual machines to run off of DC treadmill motors that run off of around 110vdc and range between 2 and 3 HP. I was hoping do the same with a cnc taig lathe. Would this be possible Marty? Thanks.
@@martyscncgarage5275 Hi Marty, thank you for your reply. Sorry if I sound ignorant; I'm very new to this all.. With my manual machines I wired up a circuit with a speed controller. It has a potentiometer that changes the voltage and the motors' rpm. I had seen a comment from you under one of Franco CNC's videos about a KBSI-240D or a similar product for applications without a VFD. Would that type of setup work for a treadmill motor?
@@backyardmachinist depends on the speed controller you use but yes, most likely. You can always just use a relay output assigned to SpinFwd to turn on and off your motor controller with M3/M5 commands. Will be up to you to set the speed
Marty how would you help me make more videos of the primary ACORN setup. Very good video. Marty como ayudaria que hiciera mas videos de la configuración primaria de ACORN. Muy buen video.
Please post your support question to the Centroid User Forums. centroidcncforum.com/viewforum.php?f=60&sid=eebe5077be996b3b456e81548813e52d Be sure to explain your setup, pictures, what kind of spindle drive/VFD etc. Also please post a FRESH Report, F7 Utilities, F7 Create Report. All Acorns are tested before they leave the factory and you are supposed to do a bench test and check the spindle output before connecting anything.
![Megan Thee Stallion - Bigger In Texas [Official Video]](http://i.ytimg.com/vi/QxTkZTLWdo4/mqdefault.jpg)
My acorn CNC when I drive my X axis 24 inches it actually moves 24 1/4 inches. How do I fix that
First did you download the Acorn Installation manual ? It's explained there.
Use the Centroid CNC Users forum. Post a fresh report and ask your question there. But it IS explained in the installation manual which can be found on Centroids website
I ran this test and had no problem, but after connecting it to the VFD, the voltage was severely loaded down, reading about a third of what it should be, and was jumping around. Turned out that not shielding the cable carrying the analog command to the VFD is a BAD idea, at least for my setup.
Make sure you only ground the shield at the Acorn end and only to one common ground point.
Marty, If this was working and now not getting any output but everything else is working fine. What have I screwed up LOL. I was trying to wire it to a KBSI-240D so clearly I did something wrong.
Post your question along with details of your build on the Centroid Acorn User forums
Thanks Marty. Somehow I missed this in all the prior videos I watched. How do I calibrate these settings so that the spindle is running at close to the RPM my g-code is setting. I have a 24K spindle that I use for carving wood most of the time around 10K to 12K but when cutting fine inly pieces the spindle speed goes way up. Thanks...
Go to the Centroid Users forum, look in the Acorn knowledge base first page VFD Tuning
Hey Marty can you explain what the limit spindle analog output to 0-5 volt option in the Acorn 4.8 update .
Primarily for spindle drives that only take 0-5vdc. However, remember that signal still need to be isolated
Hello Marty, can this test be done after the fact? I bought my board before this test existed and my machine is all assembled and VFD is hooked up..Also do I need to update to the latest version of Acorn for this test to work? Thanks for your help
Yes you can do it and yes you must (and should) upgrade to the latest version of CNC12
Do we have to hook up our spindle to a VFD? I've modified all my manual machines to run off of DC treadmill motors that run off of around 110vdc and range between 2 and 3 HP. I was hoping do the same with a cnc taig lathe. Would this be possible Marty? Thanks.
How will you change speed
@@martyscncgarage5275 Hi Marty, thank you for your reply. Sorry if I sound ignorant; I'm very new to this all.. With my manual machines I wired up a circuit with a speed controller. It has a potentiometer that changes the voltage and the motors' rpm. I had seen a comment from you under one of Franco CNC's videos about a KBSI-240D or a similar product for applications without a VFD. Would that type of setup work for a treadmill motor?
@@backyardmachinist depends on the speed controller you use but yes, most likely. You can always just use a relay output assigned to SpinFwd to turn on and off your motor controller with M3/M5 commands. Will be up to you to set the speed
Okay, thank you for confirming 🙏 Great videos!
@@backyardmachinist KBSI-240D is most likely what you will need. Search that on the Centroid Acorn User Forum
Does the maximum speed depend on your spindle motor or do you have to bench test with 0 and 3000 rpm?
The Spindle Bench test Macro requires you to set the software 0 to 3000
@@martyscncgarage5275 Awesome thanks! So this can be changed after to my spindle speeds correct? I plan on running my spindle between 16000-24000 rpm
@@janvirbrar4181 correct
Marty how would you help me make more videos of the primary ACORN setup. Very good video.
Marty como ayudaria que hiciera mas videos de la configuración primaria de ACORN. Muy buen video.
Vamos hacer mas videos nuevos.
@@martyscncgarage5275 Gracias
I'm getting 0 volts at the analog output.. bad board?
Please post your support question to the Centroid User Forums. centroidcncforum.com/viewforum.php?f=60&sid=eebe5077be996b3b456e81548813e52d
Be sure to explain your setup, pictures, what kind of spindle drive/VFD etc. Also please post a FRESH Report, F7 Utilities, F7 Create Report. All Acorns are tested before they leave the factory and you are supposed to do a bench test and check the spindle output before connecting anything.
Did you run the spindle bench test as shown in this video?