Yes, possibly, most of those techniques can be done with xp400 as well, much more control on pc side.. but when a circuit is troublesome trying to read in circuit can take a long time with trial and error.. in most cases I'll just lift a pin or 2, or just pull the chip since it usually takes just a minute.. If you have experience removing components I'd recommend lifting Vcc and S or just pulling the chip, if not in circuit reading options may be better, it's not hard to rip a pad or burn a chip with too much heat. Especially on this board you would need to mix with low melt solder to remove in a timely fashion.. Thanks for the input brother, loved the lightning truck series btw 👍🏾
@@globalcommerce7654 yeah me I just use the xp400pro cause it’s the best I got and if I do 2 reads and they don’t match I just hot air it off and move on with life. One day I might get an ar32 but it’s not high on the priority list. The lightning truck I’m still waiting on 2 things for it to be completely finished hopefully. This gm strike has put a hold up on getting a new hvac control module and a passenger front window switch lol.
If you already had the flash files couldn't you just write it with the IM608 and the XP400?. Just trying to write a flash without manufacturer software and hardware.
On this ecm, eeprom contains security data but the ecm data the actually controls the engine is stored on the mcu, most programmers cannot successfully manipulate this mcu, quicker and easier to just flash and update to the relevant calibration to the exact vehicle/engine it will serve.
@globalcommerce7654 writing a file with hp tuners. I've tried grounding the top solder joint for a second and trying to re write the original file with no luck. it just says no protocol detected.
very insightful. thanks for the videos
change your smoke detector battery
Yes sir!
can you do the pinout with gbox ?
great video man
if it possible to programming used pcm with witech2
If ur taking the eeprom can you not just put the original eeprom into the donor?
Yes
AR32 will read and write that one in circuit
Yes, possibly, most of those techniques can be done with xp400 as well, much more control on pc side.. but when a circuit is troublesome trying to read in circuit can take a long time with trial and error.. in most cases I'll just lift a pin or 2, or just pull the chip since it usually takes just a minute..
If you have experience removing components I'd recommend lifting Vcc and S or just pulling the chip, if not in circuit reading options may be better, it's not hard to rip a pad or burn a chip with too much heat. Especially on this board you would need to mix with low melt solder to remove in a timely fashion..
Thanks for the input brother, loved the lightning truck series btw 👍🏾
@@globalcommerce7654 yeah me I just use the xp400pro cause it’s the best I got and if I do 2 reads and they don’t match I just hot air it off and move on with life. One day I might get an ar32 but it’s not high on the priority list. The lightning truck I’m still waiting on 2 things for it to be completely finished hopefully. This gm strike has put a hold up on getting a new hvac control module and a passenger front window switch lol.
Pls can I use the software with j2534 device
No, it requires oem micropod2 or our version.
@globalcommerce7654 pls I have clone micropad2 but I can't flash any ECU with it when I am using it with CDA6 I get JSON error
Pls can you help me
Where l can buy the special wires you used to read the eeprom ?
amzn.to/48Q595o
👍🏾
If you already had the flash files couldn't you just write it with the IM608 and the XP400?. Just trying to write a flash without manufacturer software and hardware.
On this ecm, eeprom contains security data but the ecm data the actually controls the engine is stored on the mcu, most programmers cannot successfully manipulate this mcu, quicker and easier to just flash and update to the relevant calibration to the exact vehicle/engine it will serve.
Does cda6 provide diagnostics along with programming? Will you remotely install it if we buy?
Yes, instead of Bench mode I select, you would pick vehicle mode, every purchase comes with remote TeamViewer installation. Windows 7-11
Can you un brick gm p01 ecm
Depends.. how did you brick it?
@globalcommerce7654 writing a file with hp tuners. I've tried grounding the top solder joint for a second and trying to re write the original file with no luck. it just says no protocol detected.
Can i use a Autel J2534 passthru for the CDA software..?
No requires original micropod2 or our version..
I'm interested in the price.
Globalcommerceca.com
How can I get cda6? Do you sell that software?
Globalcommerceca.com
Can CDA6 work on windows 10
Yes