Very good job! I like how you bent the overhead arm to accommodate a guide for the blade and the use of a hinge with a spring. It reminded me of the "presser foot on a sewing machine to keep the material under pressure. I would use this new machine mostly for wood, aluminum, and plastics and use the metal bandsaw for steel. You can make a removable table for the bandsaw, or a table that the bandsaw fits into. I made one out of steel and the table is 300mm x 300mm and my bandsaw mounts onto it. It can be removed, but it stays setup most of the time. I enjoyed that you showed your mistakes and how you fixed them. We learn from our mistakes and even after 50 years of woodworking, I still make mistakes! Lol.
Thank you for all the comments. I'm very happy. It's important to learn from failure. And it seems like we'll continue to make mistakes. I was really encouraged to have a senior like you speak to me. Thank you so much 😊
![[Jigsaw table] How to make a jigsaw table that is easy to put on and take off](http://i.ytimg.com/vi/TU7Fw4gKuEE/mqdefault.jpg)
![[DIY] ジグソーテーブルとワークベンチを合体! Unite the Jigsaw table and Workbench ZC0007](http://i.ytimg.com/vi/YH7XT2zzdWc/mqdefault.jpg)
Very good job! I like how you bent the overhead arm to accommodate a guide for the blade and the use of a hinge with a spring. It reminded me of the "presser foot on a sewing machine to keep the material under pressure. I would use this new machine mostly for wood, aluminum, and plastics and use the metal bandsaw for steel. You can make a removable table for the bandsaw, or a table that the bandsaw fits into. I made one out of steel and the table is 300mm x 300mm and my bandsaw mounts onto it. It can be removed, but it stays setup most of the time. I enjoyed that you showed your mistakes and how you fixed them. We learn from our mistakes and even after 50 years of woodworking, I still make mistakes! Lol.
Thank you for all the comments. I'm very happy. It's important to learn from failure. And it seems like we'll continue to make mistakes. I was really encouraged to have a senior like you speak to me. Thank you so much 😊
鬼目ナットを付ける時にボンドを付けるのは鬼目ナットの固定ではなく、穴を開けた所の補強の為だそうです☝
自分も最初は塗っていませんでしたが、それを知ってからは塗るようになりました👍
最初のアングル製作で手曲げであそこまでキレイに曲げれるのは凄いですね😲しかも捻りまで😳
ガイドのベアリングから外れるのなら長いブレードを使うのも良いのではないでしょうか🤔
いつもありがとうございます😊
なるほど‼️穴の補強ですか‼️
そう言われると腑に落ちます‼️
ならボンドの種類も考えたほうが良さそうですね😀
ありがとうございます🙇
アングルは簡単に曲がりますよ🎶
捻りも意外に簡単に綺麗に曲がります👀
ジグソーのブレードって種類によっては短いヤツしか無いんですよ､､､特に鉄用や曲線用は､､､😳
@@DIYSUNDAY 曲線用は確かに短いのしか見たことないですね🤔
今回も創意工夫がすごいですね。失敗点も見られるのが良かったです。
溶接機は半自動ですか？手棒ですか？
ありがとうございます😊
失敗も含めてそのまんまで行こうと思ってます‼️
あえて言うならもっと失敗してます😭
溶接は半自動です🎶
@@DIYSUNDAY 失敗してこその仕上がり！素晴らしいです♪
溶接のコツといえばいいのかわかりませんが、溶接は「電気の熱で母材とワイヤが溶け合う」が基本と考えて
①母材の表面の黒皮は除去して光った状態にする。→鉄同士が一番溶けやすい。
②油分は除去しておく。→油分が熱せされると被膜になって溶けにくい。
③溶接前にバーナーで温めておく。→温度が上がる時間が短くなり溶けやすくなる。
をやるだけで結構違いますょ。
@@WiiKDIY しっかり下準備をした方が良いんですね🙆
今度試してみます😊
アドバイスありがとうございます‼️