You can actually change the mounting bracket to work on the stem. As noted on page 4 of instructions, there are four screws holding the bracket together, removing the screws allows a half turn, and then you'll be able to mount onto the stem. Also as noted in another comment, packaging includes three extra cadence sensor magnets/spare magnets. Stacking the three together they stick nicely to the backside of the peddle nut, work perfectly, eliminating the need for the cable ties and sensor mounted to your crankset.
Clint, it would be nice if you did this same video for recumbent bicycles. Most recumbents can't use the integrated speed/cadence sensor as the crank is too far away from the chainstays. The only exception maybe the Cruzbike.
If your sensor isn't reading, try getting some : 10mm X 2mm Round Disc Strong Rare Earth Magnets Neodymium N52.Take 1 or 2 of them and attach them ( they're SUPER strong) on your spoke magnet. Then your computer should work just fine.
.. and thank you for wheel measuring. never thought of putting the measure on the ground. I would mark with chalk start point, end point and measure afterwards. Too much fuss, you way is much better. But I do recommend riding the bike, not walking, especially fir MTB with lower pressure tyres - effective radius of the tyre may be up to 1cm lower (6cm in length). not huge mistake (3-5%) but still
Which wheel for speed sensor (MTB). I always thought that placing on front wheel is better (no skid, locked wheels while braking etc), but many many friends of mine believe rear is better. which one you recommend? I am speaking of speed only sensor, like the newer Garmin sensors
+Sergey Kessel I like to do the front wheel just because there's a shorter range between the sensor and head unit. Also there's less chance of oil and grime getting on it. Also you don't have the chance of your foot hitting it. So I would say the front you have a Cadence Sensor. But the new Garmin sensors actually go on the Hub which is a really neat idea. I would still put it on the front wheel.
+FestusHaggen1 I put it on my daughter's bike and she has not been riding much lately so it's hard to really say how it's held up. It's not as well made as a CatEye computer by any means but it does the job.
just curious why would you go with a cycling computer when you have a Garmin (GPS) and Cadence Sensor and speed sensors? or was this just for video content? your doing a great job by the way
great video however, if I see one more video with you using scissors or toenail clippers to trim zip ties I will lose my mind. I work in telecom and I have thrown people off the job for not using flush cut to trim them. A good pair will cost 10 buck or less and trim it "flush" with no sharp edges. Please obtain a pair, or if necessary I will send you a pair. they are also called diagonal cut pliers. sorry this is one of my many pet peeves.
+lloydy_paul Moto Style. Not too many people use it. It's probably most popular in cyclocross where you want your left hand on the rear brake when you're coming into the barriers with your right hand on the top tube.
![Digital Circus Episode 4 [TRAILER]](http://i.ytimg.com/vi/abZtsmMUbJo/mqdefault.jpg)
Great vid! Rookie cyclist so I don’t know much yet, but this video really helped me out. Thanks!
Thanks for the info. Especially getting the circumference with the tape measure 👍🏿👍🏿
Awesome man, I have the exact same Suaoki computer, thanks for walking me through
You can actually change the mounting bracket to work on the stem. As noted on page 4 of instructions, there are four screws holding the bracket together, removing the screws allows a half turn, and then you'll be able to mount onto the stem. Also as noted in another comment, packaging includes three extra cadence sensor magnets/spare magnets. Stacking the three together they stick nicely to the backside of the peddle nut, work perfectly, eliminating the need for the cable ties and sensor mounted to your crankset.
Clint, it would be nice if you did this same video for recumbent bicycles. Most recumbents can't use the integrated speed/cadence sensor as the crank is too far away from the chainstays. The only exception maybe the Cruzbike.
Thank you for a helpful video. I watched 2 others before yours and neither were of any help. Good Job!
You can find wheel circumference by measuring radius x 6 plus 5%
If your sensor isn't reading, try getting some :
10mm X 2mm Round Disc Strong Rare Earth Magnets Neodymium N52.Take 1 or 2 of them and attach them ( they're SUPER strong) on your spoke magnet. Then your computer should work just fine.
.. and thank you for wheel measuring. never thought of putting the measure on the ground. I would mark with chalk start point, end point and measure afterwards. Too much fuss, you way is much better. But I do recommend riding the bike, not walking, especially fir MTB with lower pressure tyres - effective radius of the tyre may be up to 1cm lower (6cm in length). not huge mistake (3-5%) but still
Thanks for all the steps! Really helped me out. Any idea why my cadence sensor is not picking up? The computer doesn't seem to be reading it.
+EarthPlaysMCPE they have to be pretty close to the wheel magnet. Of course make sure the battery is good in it.
Hi. Can Runtastic bike or Sport Tracker work with this sensor. Is it bluetooth Smart or Ant+ sensor?
giant for life. 😍very informative video! 👍
Which wheel for speed sensor (MTB). I always thought that placing on front wheel is better (no skid, locked wheels while braking etc), but many many friends of mine believe rear is better. which one you recommend? I am speaking of speed only sensor, like the newer Garmin sensors
+Sergey Kessel I like to do the front wheel just because there's a shorter range between the sensor and head unit. Also there's less chance of oil and grime getting on it. Also you don't have the chance of your foot hitting it. So I would say the front you have a Cadence Sensor. But the new Garmin sensors actually go on the Hub which is a really neat idea. I would still put it on the front wheel.
+Clint Gibbs yes, liked both new Garmin sensors, so easy to install and remove. especially cadence
How has that Suaoki computer held up? $20.00 on Amazon. Just curious if it's a good computer or not?
+FestusHaggen1 I put it on my daughter's bike and she has not been riding much lately so it's hard to really say how it's held up. It's not as well made as a CatEye computer by any means but it does the job.
just curious why would you go with a cycling computer when you have a Garmin (GPS) and Cadence Sensor and speed sensors? or was this just for video content? your doing a great job by the way
+pjbtruck that was for my daughter's bike. You are correct in that I only use a Garmin on my bikes.
Sir, could you state the model of that computer?
How do you turn the computer off
so one sensor is measuring the bike speed. what is the other one for..?
+Munther G-mail cadence
guess i have to google it. thanks
+Munther G-mail basically the RPM of your pedals
basically your average speed
the frequency
Pourquoi mettre le capteur à l'arrière ?
Am i the only one noticing Kevin Costner is talking?
Nope. I've heard that a lot 🙂
great video however, if I see one more video with you using scissors or toenail clippers to trim zip ties I will lose my mind. I work in telecom and I have thrown people off the job for not using flush cut to trim them. A good pair will cost 10 buck or less and trim it "flush" with no sharp edges. Please obtain a pair, or if necessary I will send you a pair. they are also called diagonal cut pliers. sorry this is one of my many pet peeves.
real cyclists have rear brake on the left!
Amen
+lloydy_paul Moto Style. Not too many people use it. It's probably most popular in cyclocross where you want your left hand on the rear brake when you're coming into the barriers with your right hand on the top tube.
moto cyclists you mean, not real cyclists? ;)
We're all real cyclist :)
+Clint Gibbs think it's a bit regional to be honest. In Australia the rear brake is always on the left.