This is the first time ive had a diesel and let alone working on a car in the engine and your ranger videos are crazy on point. Thank you so much for saving me lots of money
Love your ending bloke ! I too give away so much info on my channel from years of both my fathers experience as well as my own.... and then it takes more effort and time to make, edit and publish helpful vids along the similar lines as yours... now I simply ask for beers ( via a paypal account ) and many do oblige, some very generously. keep up with the shared knowledge, it helps and is appreciated even when most won`t show gratitude. cheers ;-)
Thanx for informing... just replaced injector 2 + 3. After having all 4 tested by a Denso and Bosch certified diesel specialist, turned out no 2 + 3 piezo part failure. But knocking still remains...🤔 Tomorrow morning I will follow your instructions. Greetings from Ambon, Maluku Ranger XLT 2.2 T6/PX1 2013 engine rebuild 01-2024
Excelente video,tengo Ford Ranger 2017. Ya me repare una averia de ADblue,con el Forscan,realmente funciona el programa. Tenia algo de miedo,si algun dia tengo que programa algun injector,pero veo que es muy sencillo,la faena sera la parte mecanica,seguire tus videos.👌
Hi ! you make great informative videos which have been very helpful in the past. I recently replaced injector number 3 on my 2.2 Everest 160 BHP and it was coded, but the vehicle is making a rough sound when accelerating and is also shaking a bit when I rev it while it is idle, Do you have any idea why does this happen ? I was reading on the internet about Pilot learn procedure will that help ?
Excellent!! i have done the what you mention on the programming of the injector but my car did not start. All i did was replacing the injector, the truck did not start. After the coding and before replacing the injector it was ok but just consume too much fuel. so i want to replace it. it show the cam sensor on the faulty but after replacing the sensor it is still the same fault. what can goes wrong?
Is it possible to temporarily override the control module to stop it from shutting the injector on a weak cylinder. Pretty sure I have a valve problem causing a low contribution situation. It shuts down cylinder one for 50 seconds and then restores power to the injector. I just found your channel and the content is great. Thank you!!!
Quick follow up question. Have you used Forscan to perform an injector re-learn ?? Injectors are noisy and have been suggested to run a relearn but never seen were this function is done thru Forscan ?? Any assistance/guidance would be appreciated. Thanks
I can't code an injector, because I don't see the diagram with the engine, I only see three numbers 4*, 5, 6, that's exactly how it appears and I can't write it!
This is the first time ive had a diesel and let alone working on a car in the engine and your ranger videos are crazy on point. Thank you so much for saving me lots of money
Love your ending bloke ! I too give away so much info on my channel from years of both my fathers experience as well as my own.... and then it takes more effort and time to make, edit and publish helpful vids along the similar lines as yours... now I simply ask for beers ( via a paypal account ) and many do oblige, some very generously. keep up with the shared knowledge, it helps and is appreciated even when most won`t show gratitude. cheers ;-)
Thank you... for taking the time out of your day to educate us....I now have the ELM327 USB ,just need the laptop when my wife's not looking lol.
Thanx for informing... just replaced injector 2 + 3. After having all 4 tested by a Denso and Bosch certified diesel specialist, turned out no 2 + 3 piezo part failure. But knocking still remains...🤔 Tomorrow morning I will follow your instructions.
Greetings from Ambon, Maluku
Ranger XLT 2.2 T6/PX1 2013
engine rebuild 01-2024
Excelente video,tengo Ford Ranger 2017.
Ya me repare una averia de ADblue,con el Forscan,realmente funciona el programa.
Tenia algo de miedo,si algun dia tengo que programa algun injector,pero veo que es muy sencillo,la faena sera la parte mecanica,seguire tus videos.👌
Thank you for sharing your knowledge, brother.👍
Hi ! you make great informative videos which have been very helpful in the past.
I recently replaced injector number 3 on my 2.2 Everest 160 BHP and it was coded, but the vehicle is making a rough sound when accelerating and is also shaking a bit when I rev it while it is idle, Do you have any idea why does this happen ?
I was reading on the internet about Pilot learn procedure will that help ?
Awesome buddy, your a legend
Can you use a OBD2 scanner to do injectors coding???
Awesome video 👍
Excellent!! i have done the what you mention on the programming of the injector but my car did not start. All i did was replacing the injector, the truck did not start. After the coding and before replacing the injector it was ok but just consume too much fuel. so i want to replace it. it show the cam sensor on the faulty but after replacing the sensor it is still the same fault. what can goes wrong?
spray starting fluid down the intake & run it on the starting fluid for about 10 seconds, i suspect you have air in your fuel lines
amigo despues que codifica inyectores tiene que programar inyeccion pilotada y programar precion de bomba de alta????
Is it possible to temporarily override the control module to stop it from shutting the injector on a weak cylinder. Pretty sure I have a valve problem causing a low contribution situation. It shuts down cylinder one for 50 seconds and then restores power to the injector. I just found your channel and the content is great. Thank you!!!
the contribution must be way out of whack for it too do that, never heard of shutting down a cylinder
Que scanner usastes? Sirve para reprogramar inyección pilotada??
Simple👍
Thanks mate
Quick follow up question. Have you used Forscan to perform an injector re-learn ?? Injectors are noisy and have been suggested to run a relearn but never seen were this function is done thru Forscan ?? Any assistance/guidance would be appreciated.
Thanks
I am also looking for assistance
Did you figure this out? Anyhelp would be great thanks
Want to know too
Hi do I need the paid version to code injectors?Or wil the 2 months trial version also work
What other things can you do on forscan like this?
quite a few things, remove seatbelt/lights chimes, check temps/boost etc,
Correction numbers are on top
Can you post a picture of the tool you are using please sir... And thank you
Sorry got it from your video 👆🏻
What is torque for injector hold down bolt
from memory 10nm plus 180 degrees
Thank u
Can U do this on the free version or do U have to get the licence?
licence, it's $15 per year
I can't code an injector, because I don't see the diagram with the engine, I only see three numbers 4*, 5, 6, that's exactly how it appears and I can't write it!
could be a software glitch, i would reinstall Forscan