Superb video sir. Although the maths went over my head, that’s because I need to learn more. In terms of understanding the flow of things, this is a brilliant video thank you. Keep up the good work
For the negative half cycle Vo = - Vi not as he explained in the video, since the output voltage should be in both cycles positive and being Vo = -Vi in the negative part makes sense ! Since the input will be negative and the negative from the rule will make the output voltage positive ...
00:06 Full wave rectifiers improve DC output to 100%. 01:43 Full wave bridge rectifier has high AC component and low efficiency. 03:08 Calculating output voltage for positive and negative half cycles 04:54 Output voltage (vo) can be calculated using Kirchhoff's voltage law 06:30 Output voltage of full wave bridge rectifier with different diode models. 08:13 Analysis of the circuit for the negative half cycle 09:44 Full wave bridge rectifier provides output voltage equal to VI. 11:20 Full wave bridge rectifier provides better output waveform than half wave rectifier.
Also in my understanding of a full wave rectifier is that the current flows in the same direction through the load resistor resulting in the correct movement of a motor hook up, especially when 2 filter capacitors are connected with a voltage regulator on the output.
In the negative half cycle the phase difference of input and output is 180 degree... But it was not cleared in your lecture... To get it is needed to gain VO=-Vin.... But you get VO=Vin...
At the output across the load resistor of the full wave rectifier in my understanding the positive waves will not fall below .7 volts which is the turn on voltage of the rectifier diodes. That means the output will not fall to zero.
Sir For the negative half cycle the input is below the x axis and if output equals input in the negative half cycle so why is it above the axis i.e in the positive region?
The actual terminology for the rectifier diodes is also forward bios and reverse bios in terms of the measurement at the anodes and cathodes, not voltage.
There are two current references, the conventional current from positive to negative and this is old before atom, electron and neutron detection. the second current is the electron current from negative to positive.
when the pot difference of the input current is higher then in cap then capacitor is charged and when the pot difference is lower then pot difference of capacitor then it supply residual current
May I ask a question? I'm always having this simple question : In AC circuit we say the polarity is constantly changing. If this is true , why we always get the hot wire on only one cable when using a test pencil ? Thank you
when you hold the tester, you are connected to the ground, the resistance in your body is high enough than earth, so you don't get shocked and the circuit is complete. try holding the tester in a way the the metallic pin at the end doesn't touch your body, you won't get any hot wire, or light.
In half wave rectifier examples...we substitute diode for voltage/battery (FB) and open circuit (RB)? But in full wave it's short circuit (FB) and open circuit (RB)?
why you are inconsistent with your explanation? During the -ve cycle if Vo = Vi, then the output waveform should contain the signal below the time axis because the Vi is below the time axis for -ve cycle.
@@mohamedkalith5965 for the negative half cycle Vo = - Vi not as he explained in the video, since the output voltage should be in both cycles positive and being Vo = -Vi in the negative part makes sense ! Since the input will be negative and the negative from the rule will make the output voltage positive ...
I don't understand how anyone who cares about understanding this stuff can dislike his videos. Superb pedagogical work. Simply outstanding. Thanks.
It just doesn't make sense. This channel's video is better than many academics I know.
Dafuq
Angreji nahi ati Bhai unhe Jo dislike marte h🤣🤣..
Chup sali
crazy d riding
This was very helpful! I wonder why this is so underrated? More people need to see this!
Thanks a lot for this amazing life-saving lecture!
I promise that after I graduate and get a good paying job, I will support your channel. My god are you helpful!
Update: I donated :)
@Ammar Ahsan Nope, going to my 3rd year this coming september! ^_^
What if you don't get a good paying job?
@@VarsneyaSrinivas just smile and leave bro no one needs your negativity here
That's such a nice initiative. We definitely owe a lot to this channel.
job to UPPCL me tab lagegi jab tu 2500000 dega
Superb video sir. Although the maths went over my head, that’s because I need to learn more. In terms of understanding the flow of things, this is a brilliant video thank you. Keep up the good work
Thank you: another excellent, clearly explained tutorial.
Im lucky that i found this channel on utube
For the negative half cycle Vo = - Vi not as he explained in the video, since the output voltage should be in both cycles positive and being Vo = -Vi in the negative part makes sense ! Since the input will be negative and the negative from the rule will make the output voltage positive ...
00:06 Full wave rectifiers improve DC output to 100%.
01:43 Full wave bridge rectifier has high AC component and low efficiency.
03:08 Calculating output voltage for positive and negative half cycles
04:54 Output voltage (vo) can be calculated using Kirchhoff's voltage law
06:30 Output voltage of full wave bridge rectifier with different diode models.
08:13 Analysis of the circuit for the negative half cycle
09:44 Full wave bridge rectifier provides output voltage equal to VI.
11:20 Full wave bridge rectifier provides better output waveform than half wave rectifier.
Whenever I get a paying job..I will support your channel..thank you for these amazing videos
Also in my understanding of a full wave rectifier is that the current flows in the same direction through the load resistor resulting in the correct movement of a motor hook up, especially when 2 filter capacitors are connected with a voltage regulator on the output.
Thank you so much for your excellent and brief explanation you helped me so much !!!
Sir you r doing great work ..Thanku so much for all these lectures
ppl watching this playlist even after 8 years ☠☠
Amazing...
Ur lecture is sooo clear...
Thank u
Random person :no one can explain physics that perfectly
Neso academy :May I come in..!!!
The best channel in youtube i guarantee at and love you sir
Really dig the color scheme haha, great video too
In the negative half cycle the phase difference of input and output is 180 degree... But it was not cleared in your lecture... To get it is needed to gain
VO=-Vin.... But you get VO=Vin...
thank you
watching 1 day before exam
2hrs before exam😅
@@kadarivinay5226 same watching 2 hours before exam
in case of negative half cycle, V out== minus(V in), you did wrong in KVC.But output waveform you have drawn correct
at 8:29 the graphs for all three cases will start and end at 0 and pi only, right?
At the output across the load resistor of the full wave rectifier in my understanding the positive waves will not fall below .7 volts which is the turn on voltage of the rectifier diodes. That means the output will not fall to zero.
This is true only for a rectifier with a capacitor filter. For rectifier without filter, output becomes zero at the start of every half cycle.
please add filter circuits
Sir
For the negative half cycle the input is below the x axis and if output equals input in the negative half cycle so why is it above the axis i.e in the positive region?
The actual terminology for the rectifier diodes is also forward bios and reverse bios in terms of the measurement at the anodes and cathodes, not voltage.
Great video. Thank you!! I am sharing this to more friends :)
Shouldn't the arrow be from negative to positive since current flow is the movement of electrons and electrons flow from negative to positive ?
mutum arnica current flows opposite to the movement of electrons.
There are two current references, the conventional current from positive to negative and this is old before atom, electron and neutron detection. the second current is the electron current from negative to positive.
Hello, direction of current is opposite to the flow of electrons...
Thank you very much, your lecture is perfectly clear!
Great tutorial :) Please keep posting
Can You make a video on how the capacitor works to smoothen the output of this circuit?
(This video was really helpful by the way)
study filters, that will cover what you need.
when the pot difference of the input current is higher then in cap then capacitor is charged and when the pot difference is lower then pot difference of capacitor then it supply residual current
Video quality 480 p❌
Content quality 4k ✅
Better than college lectures.
This video was amazing.
Neatly explained. Thanks.
Hi. I'd like to make a *FULL BRIDGE RECTIFIER!!!*
Ok. We will make a tutorial for you.
*Get your FULL BRIDGE RECTIFIER shirts now!*
why is Vo -ve? in -ve cycle
Can you make your query more clear?
Thank you very much sir.
while constructing a full-wave rectifier, a student mistakenly has swapped the terminals of d3 as depicted in figure below. explain what happens
Your teaching is amazing ! Thank you !
Mashallah Great Jazakallah Sir
Thank You Sir
May I ask a question? I'm always having this simple question : In AC circuit we say the polarity is constantly changing. If this is true , why we always get the hot wire on only one cable when using a test pencil ? Thank you
when you hold the tester, you are connected to the ground, the resistance in your body is high enough than earth, so you don't get shocked and the circuit is complete. try holding the tester in a way the the metallic pin at the end doesn't touch your body, you won't get any hot wire, or light.
Sir please make a video on filters in rectifiers
Thank you for this video. This helps me a lot. All things about this Bridge Type Full Wave Rectifier is clear to me.
Pls explain the capacitor portion in detail, why it gets smoothen ?
Capacitor retains the max voltage and discharges slowly, so the output become more smoother compared to a rectifier without filter...
In half wave rectifier examples...we substitute diode for voltage/battery (FB) and open circuit (RB)?
But in full wave it's short circuit (FB) and open circuit (RB)?
Both are correct....
thankyou. Do you have tricky exercises on it?
Thanks you sir
Includes some example from Robert l Boylestad book of full wave rectifier.
Nazmul Haque
Nazmul Haque .
why you are inconsistent with your explanation? During the -ve cycle if Vo = Vi, then the output waveform should contain the signal below the time axis because the Vi is below the time axis for -ve cycle.
Its true the second half output wave should be down the axis but he didnt give clarity
The current through the resistor is in the same direction for both the cases. Hence the positive cycles in the output.
Is it possible to keep all the negative polarity after AC is rectified to DC ?
Your query is not clear....
Please complete MOsfets jfets..
Nd thanks fr wonderful videos :)
thank you so much
Please can I know what you change the sign of the bridge terminal for the analyse of the negative ac wave?
did you know the answer? if yes explain it to me please.
why output of both cycles comes in only positive half cycle
because of the polarity of diodes...
Through load resistor, current flows only in one direction during positive and negative half cycles
@@circuitsanalytica4348 what about Vo = Vi for negative half cycle
@@mohamedkalith5965 for the negative half cycle Vo = - Vi not as he explained in the video, since the output voltage should be in both cycles positive and being Vo = -Vi in the negative part makes sense ! Since the input will be negative and the negative from the rule will make the output voltage positive ...
What is Ripple factor?
please upload more fet ,etc please
Thank sir, i have a question. Can you kindly explain sir what is the main advantage of bridge over center tapped? Thank sir from india
For center tapped, the secondary winding is double the size of secondary of transformer in a bridge rectfier
Center tapped rectifier is expensive and bulky bcoz it uses center tapped transformer
Nice explanation, but he should be louder
what will e the efficiency if a resistor is connected with every diode?
Output voltage falls, so efficiency falls....
excellent explaination...good voice
Thank u 💞
Nice video
Why the D1 is reversed biased
how is diode D3, .. (FB)?
Woooow your the best
thanks
nganong naay resistor sa tunga ?
Tq sir
great
Whats your age ?
Pitaji aap achay pitaji hein
I make that circuit and then it blow my circuit and my house turn off all light whyyyyyyyy
chalak...
aami kichu bujhte paarbe na
aami akdom bokkaa , aami kichu jaani na